Руководство по эксплуатации Drolet EPA HT-1600

Руководство по эксплуатации для устройства Drolet EPA HT-1600

Устройство: Drolet EPA HT-1600
Категория: Плита
Производитель: Drolet
Размер: 0.42 MB
Добавлено: 5/27/2014
Количество страниц: 28
Печатать инструкцию

Скачать

Как пользоваться?

Наша цель - обеспечить Вам самый быстрый доступ к руководству по эксплуатации устройства Drolet EPA HT-1600. Пользуясь просмотром онлайн Вы можете быстро просмотреть содержание и перейти на страницу, на которой найдете решение своей проблемы с Drolet EPA HT-1600.

Для Вашего удобства

Если просмотр руководства Drolet EPA HT-1600 непосредственно на этой странице для Вас неудобен, Вы можете воспользоваться двумя возможными решениями:

  • Полноэкранный просмотр -, Чтобы удобно просматривать инструкцию (без скачивания на компьютер) Вы можете использовать режим полноэкранного просмотра. Чтобы запустить просмотр инструкции Drolet EPA HT-1600 на полном экране, используйте кнопку Полный экран.
  • Скачивание на компьютер - Вы можете также скачать инструкцию Drolet EPA HT-1600 на свой компьютер и сохранить ее в своем архиве. Если ты все же не хотите занимать место на своем устройстве, Вы всегда можете скачать ее из ManualsBase.
Drolet EPA HT-1600 Руководство по эксплуатации - Online PDF
Advertisement
« Page 1 of 28 »
Advertisement
Печатная версия

Многие предпочитают читать документы не на экране, а в печатной версии. Опция распечатки инструкции также предусмотрена и Вы можете воспользоваться ею нажав на ссылку, находящуюся выше - Печатать инструкцию. Вам не обязательно печатать всю инструкцию Drolet EPA HT-1600 а только некоторые страницы. Берегите бумагу.

Резюме

Ниже Вы найдете заявки которые находятся на очередных страницах инструкции для Drolet EPA HT-1600. Если Вы хотите быстро просмотреть содержимое страниц, которые находятся на очередных страницах инструкции, Вы воспользоваться ими.

Краткое содержание
Краткое содержание страницы № 1





OWNER`S MANUAL
DROLET EPA WOODSTOVES

HT-1600 & HT-2000




US ENVIRONMENTAL PROTECTION
AGENCY PHASE II CERTIFIED
WOODSTOVES


Vérified and tested following
ULC S627 et UL 1482 Standards by:







READ AND KEEP THIS MANUAL FOR REFERENCE


Manufactured by : STOVE BUILDER INTERNATIONAL INC.
1700, Léon-Harmel, Québec (Québec) G1N 4R9
Tel : ( 418 ) 527-3060
Fax : ( 418 ) 527-4311
www.drolet.ca


45060A

Краткое содержание страницы № 2

TABLE OF CONTENTS INTRODUCTION.................................................................................................................. 2 TECHNICAL SPECIFICATIONS .......................................................................................... 3 TIPS ON WOOD HEATING ................................................................................................. 4 ASSEMBLY..................................................................................................

Краткое содержание страницы № 3

INTRODUCTION SBI INC., one of the most important wood stove and fireplace manufacturers in Canada, congratulates you on your purchase and wishes to help you get maximum satisfaction from your wood stove. In the pages that follow, we will give you advice on wood heating and controlled combustion as well as technical specifications regarding installation, operation and maintenance of the model you have chosen. The instructions pertaining to the installation of your wood stove comply wit

Краткое содержание страницы № 4

TECHNICAL SPECIFICATIONS HT-1600 HT-2000 Combustion Type: Wood Wood 2 2 Recommended Surface 900 à 1 600 ft 1 000 à 2 000 ft 2 2 (84 à 149 m ) (93 à 186 m ) 40 000 BTU/h 60 200 BTU/h Heating Capacity : E.P.A : (11,7 kW) (17,6 kW) 70 000 BTU/h 95 000 BTU/h Real : (20,5 kW) (27,8 kW) Efficiency : 71,3% 72,2% Average Emission: 3,3 g/h 3,8 g/h Colour : Metallic Black Metallic Black Flue Pipe Diameter : 6’’ (152 mm) 6’’ (152 mm) Chimney type : 2 100°F (650 °C) 2 100°F (650 °C) M

Краткое содержание страницы № 5

TIPS ON WOOD HEATING Wood is a renewable energy. It is also a very clean heat source when used with appliances that are certified by the U.S. Environmental Protection Agency (EPA), a standard accepted in Canada as well. EPA-certified wood stoves are different than conventional wood stoves. Burning with an EPA-certified wood stove may therefore require that you modify some of your heating habits. To get the most satisfaction out of your new wood-heating system, please make sure you go t

Краткое содержание страницы № 6

ASSEMBLY PEDESTAL AND DECORATIVE SIDEWALL INSTALLATION Pedestal Installation : 1. Remove all bricks and insulations in the appliance. 2. Slowly, lay down the stove on his back. 3. Install legs or the pedestal with the supplied nuts and bolts. Stand up the stove and place it with the required clearances. Note that there is eight holes in the bottom of the stove but only four will align with the pedestal. 4. Slide the front part of the pedestal base around the pedestal and

Краткое содержание страницы № 7

BRICKS AND INSULATION INSTALLATION (HT-1600) 1. Remove from the stove all bricks and insulation. 2. Install all side bricks (11 x 4 1/2" x 9" & 1 x 4 ½” x 8 3/16") as shown in drawing below. 3. Install the back bricks (6 x 4 1/2" x 9") 4. Install the bottom bricks (4 x 4 1/2" x 9") + (2 x 6 " x 8") and the ash cap. 5. Install the "T" shape support. 6. Install the baffle bricks (4 x 4 1/2" x 9") + (2 x 3" x 9") on T shape support. 7. Finally, gently slide the insulation panels over th

Краткое содержание страницы № 8

BRICK AND INSULATION INSTALLATION (HT-2000) The stove is normally supplied with secondary air tubes in position. To install the baffle bricks and white ceramic insulation, it’s necessary to remove the two front secondary air tubes. First place only one baffle brick and one white ceramic insulation. Use the same method to put the other baffle brick and insulation. Put back in place the secondary air tubes. Install the yellow insulation and the 6" x 8" or 6" x 6" bricks. Install the

Краткое содержание страницы № 9

AIR TUBES INSTALLATION (HT-2000): The secondary air tubes are painted different colours . The back tube is yellow, the middle on is red and the front is unpainted. Before installing, make sure the locating holes in the tubes (holes near one end of the tube) are on the left side. Insert one tube in the right side air channel and slide it to the right as much as possible. Bring the left end of the tube aligned with the ring welded to the left air channel. Move the tube to the left until the

Краткое содержание страницы № 10

DOOR ADJUSTMENT In order for your stove to operate properly, the door should be adjusted periodically to provide an air tight fit. To adjust: • Remove the lock pin (spring pin) by pulling and turning it using pliers ("wise grip") • Turn the handle counter clock wise one turn to increase pressure • Re-install the lock pin (spring pin) with a small hammer Figure 5: Door Adjustment 9

Краткое содержание страницы № 11

THE BENEFITS OF INSTALLING A BLOWER A blower can be installed at the back of your DROLET stove. This option is necessary if you wish to redistribute into a room the heat trapped at the back of your stove. By forcing hot air toward the front, the blower enables you to extend the radiation power of your stove. You can purchase this option through your DROLET dealer. Make sure to specify this part number: #AC02050. You can also install a thermodisc to enable the blower to start or stop au

Краткое содержание страницы № 12

INSTALLATION SAFETY NOTICE • IF THIS STOVE IS NOT PROPERLY INSTALLED, A HOUSE FIRE MAY RESULT. TO REDUCE THE RISK OF FIRE, FOLLOW THE INSTALLATION INSTRUCTIONS. FAILURE TO FOLLOW INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE, BODILY INJURY, OR EVEN DEATH. • CONSULT YOUR MUNICIPAL BUILDING DEPARTMENT OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATIONS REQUIREMENTS IN YOUR AREA. • USE SMOKE DETECTORS IN THE ROOM WHERE YOUR STOVE IS INSTALLED. • KEEP FURNITURE AND DRAPES WELL AWAY FROM

Краткое содержание страницы № 13

FLOOR PROTECTOR Your wood stove should be placed on a non-combustible surface. The floor protector should be under the stove, eighteen inches beyond the front and eight inches beyond each side of the fuel loading and ash removal opening. If there is a horizontal section of chimney connector, the floor protector should go under it and two inches beyond each side. The floor protector should exceed the stove as follows: FRONT SIDES BACK 18’’ 8’’ 8’’ (460 mm) (200 mm) (200 mm)

Краткое содержание страницы № 14

CLEARANCES It is of utmost importance that the clearances to combustible material be scrupulously respected upon installation of the stove you have selected. Refer to the tables below : Figure 6: Clearances to combustibles CANADA Single pipe / Double pipe Model A B C D E F HT-1600 15/12 16/16 12/10 20.8/17.8 28.7/28.7 25.2/23.2 HT-2000 19/10 19/14 11/8 25.4/16.4 33.1/28.1 25.5/22.5 USA Single pipe / Double pipe Model A B C D E F HT-1600 15/12 16/16 12/10 20.8/17.8 28.7/28.7 25.

Краткое содержание страницы № 15

REDUCED CLEARANCES You may decrease the clearances by installing heat radiation shields between the walls or the ceiling and the stove. These heat radiation shields must be installed permanently, and can include sheet metal, a rigid non-combustible sheet or a masonry wall. Clearances of not less than 1" (25 mm) and not more than 3" (76 mm) between the bottom of the shield and the floor and not less than 3" (76 mm) between the top of the shield and the ceiling must be respected to allow

Краткое содержание страницы № 16

CHIMNEY Your wood stove may be hooked up with a factory built or masonry chimney. If you are using a factory built chimney, it must comply with UL 103 or ULC S629 standards; therefore it must be a Type HT (2100°F). It is extremely imp ortant that it be installed according to the manufacturer's specifications. If you are using a masonry chimney, it is important that it be built in compliance with the specifications of the National Building Code. It must be lined with fire clay bricks,

Краткое содержание страницы № 17

CHIMNEY CONNECTOR (STOVE PIPE) Your chimney connector and chimney must have the same diameter as the stove outlet. If this is not the case, we recommend you contact your dealer in order to insure there will be no problem with the draught. The stove pipe must be made of aluminized or cold roll steel with a minimum thickness of 0.021" or 0.53 mm. It is strictly forbidden to use galvanized steel. Your smoke pipe should be assembled in such a way that the male section of the pipe faces down

Краткое содержание страницы № 18

TYPICAL INSTALLATIONS FACTORY BUILT CHIMNEY: RAIN CAP ROOF FLASHING 18" CLEARANCE RADIATION SHIELD WALL RADIATION SHIELD WALL SUPPORT CEILING SUPPORT Wall installation Vertical installation 17

Краткое содержание страницы № 19

MASONRY CHIMNEY: Clay liner Thimb le Clean out door 18

Краткое содержание страницы № 20

FACTORY BUILT THIMBLE: 19


Скачавание инструкции
# Руководство по эксплуатации Категория Скачать
1 Drolet 1800 Руководство по эксплуатации Плита 2
2 Drolet 1800 EPA Руководство по эксплуатации Плита 0
3 Drolet 45283 Руководство по эксплуатации Плита 3
4 Drolet 58991 Руководство по эксплуатации Плита 1
5 Drolet 1500 EPA Руководство по эксплуатации Плита 0
6 Drolet 1500 Руководство по эксплуатации Плита 0
7 Drolet 75281 Руководство по эксплуатации Плита 0
8 Drolet AC02080 Руководство по эксплуатации Плита 1
9 Drolet Baron 1880 SP Руководство по эксплуатации Плита 12
10 Drolet 45521A Руководство по эксплуатации Плита 0
11 Drolet Baron 2000 SP Руководство по эксплуатации Плита 3
12 Drolet ALASKA 2000 Руководство по эксплуатации Плита 10
13 Drolet CS1200 Руководство по эксплуатации Плита 0
14 Drolet COMPAK EPA EXEMPT 45109A Руководство по эксплуатации Плита 1
15 Drolet DB02900 Руководство по эксплуатации Плита 0
16 Edelbrock 2006-2007 (N) Руководство по эксплуатации Плита 4
17 Aarrow Fires SF 50 Руководство по эксплуатации Плита 1
18 Aarrow Fires EcoBurn BK043 Руководство по эксплуатации Плита 0
19 Aarrow Fires EcoBurn AFS1221 Руководство по эксплуатации Плита 0
20 Aga Ranges Berrington Руководство по эксплуатации Плита 3