Краткое содержание страницы № 1
6” BENCH GRINDER
Model 90003
ASSEMBLY AND OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at: http://www.harborfreight.com
®
Copyright 2003 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions, please call 1-800-444-3353.
Краткое содержание страницы № 2
PRODUCT SPECIFICATIONS
!
"#$%& %' ()*(+ *(
(
*-(
/5*(6 %(((
7((8
(
:;&<:;5&$:#;= 7((/ :;=&$:;5&":#;8! /%(
( ";8 5 $ $(
+ SAVE THIS MANUAL You will need this manual for the safety warnings and precautions, assembly, operating, inspection,
Краткое содержание страницы № 3
3. Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. Protect others in the work area from debris such as chips and sparks. Provide barriers or shields as needed. ELECTRICAL SAFETY 4. Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way. Do not use any adapter plugs. Check with a qualified ele
Краткое содержание страницы № 4
11. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. 12. Avoid accidental starting. Be sure the Power Switch is off before plugging in. Carrying power tools with your finger on the Power Switch, or plugging in power tools with the Power Switch on, invites accidents. 13. Remove adjusting keys or wrenches before turning the power tool on. A
Краткое содержание страницы № 5
22. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly main- tained tools. 23. Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may become hazardous when used on another tool. SERVICE 24. Tool service must be performed only by qualified repair personnel.
Краткое содержание страницы № 6
7. Always maintain a 1/16” distance or less between the Grinding Wheels (part #64) and Left and Right Tool Rests (parts #28, #32) as the diameter of the Grinding Wheels decrease with use. 8. To avoid accidental electrical shock, do not allow the Power Switch (part #3) to become wet. Do not touch the Power Switch with wet hands. 9. When using the Bench Grinder, always maintain a firm grip on the object being ground with both hands. 10. To avoid accidental burns use caution when handling an objec
Краткое содержание страницы № 7
22. Always turn off the Bench Grinder and unplug it from its electrical outlet before changing accessories or performing any inspection, mainte- nance, or cleaning procedures. 23. WARNING! The warnings and cautions discussed in this manual cannot cover all possible conditions and situations that may occur. It must be under stood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied the the operator. 24. WARNING!
Краткое содержание страницы № 8
2. The grounding prong in the plug is connected through the green wire inside the cord to the grounding system in the tool. The green wire in the cord must be the only wire connected to the tool’s grounding system and must never be attached to an electrically “live” terminal. (See Figure A.) 3. Your tool must be plugged into an appropriate outlet, properly installed and grounded in accordance with all codes and ordinances. The plug and outlet should look like that in the following illustratio
Краткое содержание страницы № 9
EXTENSION CORDS 1. Grounded tools require a three wire extension cord. Double Insulated tools can use either a two or three wire extension cord. 2. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage. (See Figure C, next page.) 3. The smaller the gauge number of the wire, the greater the capacity of the cord. For exa
Краткое содержание страницы № 10
SYMBOLOGY Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. Volts Alternating Current V ~ Amperes A No Load Revolutions n o xxxx/min. per Minute (RPM) UNPACKING When unpacking, check to make sure all the parts shown on the Parts List on page 15 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. ASSEMBLY INSTRUCTIONS NOTE: For additional information regarding the par
Краткое содержание страницы № 11
3. Repeat Steps #1 and #2 to attach the Right Tool Rest (part #32) to the Right Wheel Guard (part #31). (See Figure D.) SCREW WITH LOCK WASHER (#25) LEFT WHEEL RIGHT WHEEL GUARD GUARD (#27) (#31) LEFT TOOL RIGHT TOOL REST REST (#28) (#32) FIGURE D To Attach The Spark Guards: 1. Align the mounting slot in the Left Spark Guard (part #62) with the threaded mounting hole in the Left Wheel Guard (#27). Insert one Screw (part #59) with one Washer (part #60) through the mounting slot in the Left Spar
Краткое содержание страницы № 12
To Attach The Eye Shield Mounting Rods: 1. Insert one Screw (part #48) with a Washer (part #13) through a Bracket (part #36) and the Left Eye Shield Mounting Rod (part #49). Then, firmly tighten the Screw to secure the Left Eye Shield Mounting Rod to the body of the Bench Grinder. (See Figure F.) 2. Repeat Step #1 to attach the Right Eye Shield Mounting Rod (part #33) to the body of the Bench Grinder. (See Figure F.) BRACKET (#36) BRACKET (#36) WASHER (#13) WASHER (#13) RIGHT EYE SCREW (#48)
Краткое содержание страницы № 13
EYE SHIELD (#26) EYE SHIELD (#26) PRESSURE PLATE PRESSURE PLATE (#50) (#50) LEFT EYE SHIELD RIGHT EYE SHIELD MOUNTING ROD MOUNTING ROD (#49) (#33) SCREW SCREW (#55) (#55) FIGURE G 2. There are two 11/32” diameter mounting holes located on the Base (part #15) of the Bench Grinder. (See Figure H.) 3. Temporarily set the Bench Grinder in the desired location on the workbench. Use the two 11/32” diameter mounting holes on the Bench Grinder as templates to mark where two 11/32” diameter holes will
Краткое содержание страницы № 14
OPERATING INSTRUCTIONS 1. WARNING! Prior to using the Bench Grinder, make sure to wear ANSI approved safety glasses, full face safety impact shield, and heavy duty work gloves. Also, always adjust the two Eye Shields (part #26) directly in line between your eyes and the object being ground. (See Figure H.) Always keep wheel covers in place when using the Bench Grinder. 2. Plug the Power Cord Plug (part #10) into the nearest grounded, 120 volt, electri- cal outlet. Then, turn the Power Switc
Краткое содержание страницы № 15
3. TO CLEAN: Use vaccum or a clean cloth and mild detergent to clean the body of the Bench Grinder. Do not use solvents. Do not immerse any part of the tool in liquid. PARTS LIST '7 @ '7 @ (( "" ]+%(
(+ ( "# / " ()) "$ ^^'(( # # ()*(+ " / $ /
" /
*!( "< 5_ " ) "` 7
{*!( <*!(* ! # 7
{)
Краткое содержание страницы № 16
ASSEMBLY DIAGRAM 58 26 33 57 13 58 36 52 53 51 62 48 13 54 61 54 59 29 53 46 52 48 50 36 1 50 60 59,60 28 30 63 55 12 55 24 64 26 51 13 56 5 63 27 57 24 25 19 50 40 31 20 18 23 25 18 25 24 32 21 20 22 12 13 9 17 5 2 16 37 45 15 7 40 39 4 44 14 3 38 6 8 10 44,45 41 35 42 47 43 48 44 34 45 NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED
