Краткое содержание страницы № 1
Programming
<
Washer-Extractors
Cabinet Hardmount
B-Series Microcomputer for Coin Models
2 Speed and Variable-Speed
Refer to Page 7 for Model Identification
NORMAL PERM PRESS
WASH
HOT WARM
ADD
NORMAL PERM PRESS
BLEACH
RINSE
WARM COLD
SPIN
QUICK WH AS QUICK WASH
START
DOOR
HOT WARM
HEAVY SOIL DELICATE
HOT COLD
DOMESTIC MODELS
CHM4
CHM482R
95C 95C
60C 60C
40C 40C
30C
INTERNATIONAL MODELS
CHM488R
CHM488R
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual m
Краткое содержание страницы № 2
Краткое содержание страницы № 3
Safety Information.............................................................................. 3 Table of Explanation of Safety Messages........................................................... 3 Important Safety Instructions ............................................................... 3 Contents Safety Decals ........................................................................................ 5 Operator Safety..........................................................................
Краткое содержание страницы № 4
Temperature Probe Malfunction ...................................................... 27 Rapid Advance (For Models With Firmware ID Code “C2HL” and “CuHL”) ............................................................................................. 27 Enabling Rapid Advance ................................................................. 27 How to Rapid Advance During All Steps (Except First Fill Step)..................................................................... 27 How to Rapid Advanc
Краткое содержание страницы № 5
Safety Information Explanation of Safety Messages Important Safety Instructions Precautionary statements (“DANGER,” “WARNING,” WARNING and “CAUTION”), followed by specific instructions, are found in this manual and on machine decals. These To reduce the risk of fire, electric shock, precautions are intended for the personal safety of the serious injury or death to persons when operator, user, servicer, and those maintaining the using your washer, follow these basic machine. precautions:
Краткое содержание страницы № 6
Safety Information 9. Do not install or store the washer where it will be 20. If the supply cord is damaged, it must be replaced exposed to water and/or weather. by a special cord or assembly available from the manufacturer or its service agent. 10. Do not tamper with the controls. 21. Be sure water connections have a shut-off valve 11. Do not repair or replace any part of the washer, or and that fill hose connections are tight. CLOSE attempt any servicing unless specifically the shut-off
Краткое содержание страницы № 7
Safety Information WARNING CAUTION This machine must be installed, adjusted, Be careful around the open door, and serviced by qualified electrical particularly when loading from a level maintenance personnel familiar with the below the door. Impact with door edges construction and operation of this type of can cause personal injury. SW025 machinery. They must also be familiar with the potential hazards involved. Failure to observe this warning may result in personal injury and/or equipment
Краткое содержание страницы № 8
Safety Information Do not bypass any safety devices in the machine. Operator Safety WARNING WARNING NEVER insert hands or objects into Never operate the machine with a basket until it has completely stopped. bypassed or disconnected balance Doing so could result in serious injury. system. Operating the machine with SW012 severe out-of-balance loads could result in personal injury and serious equipment To ensure the safety of machine operators, the damage. following maintenance checks mus
Краткое содержание страницы № 9
Introduction Model Identification Information in this manual is applicable to these models: HC20BC2 HC30BY2 HC60BXF SC20BX2 SC40BL2 SC60BYF HC20BL2 HC40BC2 HC60BYF SC20BY2 SC40BX2 SC60BY2 HC20BX2 HC40BL2 HC60BY2 SC25BC2 SC40BY2 SC80BCV HC20BY2 HC40BX2 HC80BCV SC25BL2 SC50BC2 SC80BLV HC25BC2 HC40BY2 HC80BLV SC25BX2 SC50BY2 SC80BXV HC25BL2 HC50BC2 HC80BXV SC25BY2 SC60BC2 SC80BYV HC25BX2 HC50BY2 HC80BYV SC30BC2 SC60BCF SC125BCV HC25BY2 HC60BC2 HC125BCV SC30BL2 SC60BL2 SC125BYV HC30BC2 HC60BCF HC12
Краткое содержание страницы № 10
Introduction Nameplate Location Replacement Parts The nameplate is located at the rear of the machine and If literature or replacement parts are required, contact inside door. Always provide the machine’s serial the source from whom the machine was purchased or number and model number when ordering parts or contact Alliance Laundry Systems at (920) 748-3950 when seeking technical assistance. for the name and address of the nearest authorized parts distributor. 1 Customer Service For technica
Краткое содержание страницы № 11
Introduction 7. Supply 2 (bleach) (S2) Electronic Control Unit 8. Supply 3 (sour/softener) (S3) The “B” electronic control is composed of the electronic control unit and the control fuse board with 9. Optional 3rd (Extra) Fill Inlet (governed by the wiring harness. Only an authorized person should look configuration settings) (S4) inside the control compartment. First TURN OFF 10. Optional Heat (HT) POWER, open lid and remove any cover present. Make sure door lock circuit has fully dischar
Краткое содержание страницы № 12
Introduction Third Party Card Reader Communications (Card Reader Models Only) Central Pay System The models are usually designated by the “Prep for (Central Pay System Models Only) Card Reader” option. The model number will have a The models are usually designated by the “Prep for “Y” in the 6th digit (i.e. *C40BY2OU6001). Refer to Central Pay” option. The model number will have an Nameplate Location. The control will accept “L” in the 6th digit (i.e. *C40BL2OU6001). Refer to communication
Краткое содержание страницы № 13
Introduction Model Number Familiarization Guide Sample Model Number: *C40BY2OU60001 Model Number Prefix *C Washer-Extractor Capacity (pounds dry weight of laundry) 40 Type of Electrical Control B Actuation (Y = Prep for Card Reader) Y Washer-Extractor Speed Capability (2 = 2 speed) 2 Electrical Characteristics O Design Series U6 Option Identification (varies from machine to machine) 0001 * Denotes Brand *C40BY2OU60001 00000000000 208 – 240 7 3 60 3 3 60 18 470 N/A N/A 0 500000 EXAMPLE OF NAMEPL
Краткое содержание страницы № 14
Programming NOTE: The machines are factory programmed with basic cycles to make the units operational without programming at installation. Entering Program Mode 1. Open machine lid. 2. Locate Program/Run switch on the computer board. This is accessed through a cutout in the metal control unit cover. This switch protrudes from the rear of the electronic control unit cover. 3. Flip switch to the left (as seen from front of machine) to enter PROGRAM Mode. 4. Display will show “0000” or tempe
Краткое содержание страницы № 15
Programming 8. If model displays the message “CArd” or Programming Vend Price “COIn”, change the selection by pressing the (∧) (For Models with Firmware ID Code or (∨) keypad. “C2dS” and “CvdS”) 9. Press START (Enter) keypad to continue to the next selection. Setup Mode NOTE: Select “COIn used by accessory pay NOTE: In SETUP Mode, certain machine system. Contact the manufacturer of the accessory functions can be configured. The settings in this pay system if not working properly mode a
Краткое содержание страницы № 16
Programming 18. Display shows “con2”, “dEno” next, then a 7. Press START (Enter) keypad. Displays show a number such as 100. This means that the coin 2 number (up to 4 digits) showing how many denomination is 100 cents. This is the coin complete cycles have been operated. This denomination for coin meters that can process excludes cycles stopped because of an error. two types of coins – such as a U.S. quarter/dollar 8. Press START (Enter) keypad. coin meter. The second coin input would be
Краткое содержание страницы № 17
Programming NOTE: If neither message displays, the extra fill Programming Vend Price capability is not present. If either message displays, (For Earlier Models) changing the selection is an option by pressing the (∧) or (∨) keypad. Press START (Enter) keypad Setup Mode to continue to the next option. NOTE: In SETUP Mode, certain machine 10. If model displays the message “CArd” or functions can be configured. The settings in this “COIn”, change the selection by pressing the (∧) mode are
Краткое содержание страницы № 18
Programming NOTE: If machine is equipped with a card reader, Cycle and Error Count or interfaces with a control/remote pay system, The control logs cycle count (total of all cycles setting “con1”/ “dEno” and “con2”/ “dEno” equal completed). to the vend start amount (“Strt”/ “Ant”) will allow starting with one pulse and is recommended. The 1. To read, enter PROGRAM Mode. Refer to card or central remote pay vend amount should Entering Program Mode. match the “Strt”/ “Ant” setting. 2. Press
Краткое содержание страницы № 19
< Programming 1 1 2 2 5 5 15 15 NORMAL PERM PRESS 95C 95C 6 WASH 14 HOT WARM 6 14 ADD NORMAL PERM PRESS BLEACH 60C 60C 13 RINSE 13 WARM COLD 7 7 SPIN QUICK WH AS QUICK WASH 12 12 40C 40C START DOOR HOT WARM 8 8 11 HEAVY SOIL DELICATE 11 30C HOT COLD 10 10 CHM482R CHM488R 9 3 4 9 3 4 DOMESTIC MODELS INTERNATIONAL MODELS CHM482R CHM488R 1 Cycle 1 9 START (Enter) Keypad 2 Cycle 2 10 “Clean Filter” Indicator LED (Active only for 3 Cycle 3 C60FX, C80 and C125 Models) 4 Cycle 4/ “∧” Edit 11 Door Open
Краткое содержание страницы № 20
Programming Options for Each Segment Cycle Steps Available (NOTE: WASH, ADD BLEACH, RINSE Display Setting Options for Cycle Steps and SPIN LEDs light ONLY when a cycle formula is in operation.) Wash 1 (displayed as “USH1”) Time for Agitation (excludes fill, drain, GEnt 0 or 2-30 minutes in agitation step (increases/decreases in spin and heat) one-minute increments). Refer to Table 3 for operation of norn each agitation segment Fill valves (temperature) CFIL Cold, Hot or Both (warm) water fi
