Краткое содержание страницы № 1
R
INSTALLATION
AND
OPERATING
INSTRUCTIONS
TM
X’Vert
Model: VSX
VERTICAL CONTACT BUN GRILL TOASTER
INTENDED FOR OTHER THAN HOUSEHOLD USE
RETAIN THIS MANUAL FOR FUTURE REFERENCE
TOASTER MUST BE KEPT CLEAR OF COMBUSTIBLES AT ALL TIMES
FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
! !
WARNING: Improper installation, adjustment, alteration, service or maintenance can
cause property damage, injury or death. Read the
Краткое содержание страницы № 2
TABLE OF CONTENTS SECTION ITEM ........ PAGE 1 Owner’s Information 2 2 Safety Information 2 3 Specifications 3 4 Operation .. 4 5 Cleaning & Release Sheet Care & Replacement 6 6 Troubleshooting 7 7 Preventative Maintenance Schedule 10 8 Wiring Diagram 13 9 Parts List & Exploded View 14 10 Procedure: Conveyor Belt Tracking 16 11 Procedure: Changing a Belt 16 12 Procedure: Splicing The Conveyor Chain 17 13 Procedure: Conveyor Belt Adjustment 19 14 Warranty 20 1. OWNER’S INFORMATION General Informa
Краткое содержание страницы № 3
Operating toaster without legs will void the warranty. Insure all accessories and exterior panels are properly installed and adjusted before applying power and operating. 3. SPECIFICATIONS Cordset Configuration: 208/240V: NEMA6-20P plug, 3 foot, 3 wire grounded cord. 208/240V: NEMA6-20P plug (90° angle), 5 foot, 3 wire grounded cord. If the supply cord is damaged, the manufacturer or an authorized service agent (or a similarly qualified person) must replace it to avoid a hazard. Failure to repla
Краткое содержание страницы № 4
4. OPERATION Operating Instructions (see figure #4) This toaster is for Dry operation only (no oil). Do not put buttered bread products in the toaster. Ensure Release Sheets are properly installed. (See page 7.) Turn Main Power Switch on. Set Temperature Control to desired temperature. (Temperature is factory set at 600°F.) Allow Pilot Light to cycle at least two times (on/off). When the light is on, the grill is heating. Heat up time is about 15 minutes. FIGURE 2: Place bun halves on fe
Краткое содержание страницы № 5
Status,Alarm, and Error Messages (See Figure 3) rdY Control is at set point and the toaster is ready for operation. Lo Actual temperature is below set point. After toaster has reached “rdY,” then this indicates that the platen is less than 50°F below the set point (too cold). Hi Actual temperature is above set point. Prb The temperature probe (sensor) is disconnected or defective. HIE Actual temperature is at least 50°F above set point, indicating that there is a controller error. FIGURE 5: FIGU
Краткое содержание страницы № 6
5. CLEANING Cleaning Instructions Toaster is for DRY BUNS ONLY. Do not put buttered bread products in FIGURE 7: the toaster. TOASTER PARTS Note: To save time at closing (it will take 15 minutes for toaster to cool (PIEZAS DE LA TOSTADORA) down), you might want to have the day shift clean the toaster. 1. Turn off (7) Main Power Switch (See Fig. 7).Allow toaster to cool down. 2. Remove (6) Bun Slide and (1) Top Cover (See Fig. 7) & wash in sink. 1 3. For ease of cleaning, turn the toaster so that
Краткое содержание страницы № 7
Release Sheet Care and Replacement A C D/E B G H F I L M N J/K u T . f f o . T R S t p T Y O T .E B H a c d a p r o s s s a c r P y b C T s A c s s R S f i t s c f I S a o t i n i t , s t , t t t I s i o t p u s o b s s c . F s a S f t S ( i t . G u T b c c T D R S t p R S t n o t t c t t S Y .E B H c r t p t t c . t s o t m t r R S t o t t p t T D 6. TROUBLESHOOTING GUIDE Always ask and check the following: c o t a p t . b Service Hotline (800) 733-2203 t s I t c o t t T p C L 7 above). Figure
Краткое содержание страницы № 8
Problem Possible Cause Corrective Action (See page 9)
Краткое содержание страницы № 9
Problem Corrective Action Possible Cause Crown and / ro heel must Release Sheet and / or Silicone Belt need Clean or replace Release Sheet or Silicone Belt according to be forced into the . toaster cleaning. The instructions in this manual. Bun Chute roperly imp installed. Review installation instructions and relocate Bun Chute. erify V that the bottom of the Bun Chute is level and setting flat on the counter or table. oaster T is overheating or Dirt and -up build no the n a F l B urn T the unit
Краткое содержание страницы № 10
7. PREVENTATIVE MAINTENANCE SCHEDULE Tools required: Daily: Heat Resistant Gloves, Standard Cleaner, Standard Sanitizer, Cleaning Pad. Weekly: Lubricant 3-6 Months: Needle Nose Pliers, Standard Cleaner, Standard Sanitizer, Cleaning Pad Yearly: Phillips Screwdriver, Standard Lubricating Oil, Needle Nose Pliers 1) Preventative Maintenance - Daily WARNING! Toaster may be hot. Allow to cool before cleaning. Use heat resistant gloves when removing the top cover, cleaning the Release Sheet, and cleani
Краткое содержание страницы № 11
4) Preventative Maintenance Yearly A. In addition to the daily cleaning described above, remove the silicone belts according to the instructions described in (3), and inspect the metal conveyor chain. Check the tension to make sure that drive sprockets are engaging all the wires in the metal conveyor chain. If the sprockets are not engaging all the wires, if the metal belt is too loose, making noise, or exhibits any other indication of being unusually loose, remove a link from the chain. See ins
Краткое содержание страницы № 12
IMPORTANT FOR FUTURE REFERENCE Please complete this information and retain this manual for the life of the equipment. For Warranty Service and/or Parts, this information is required. Model Number Serial Number Date Purchased Notes 12
Краткое содержание страницы № 13
BLACK BLACK 115 208 230 8. WIRING DIAGRAMS FIGURE 9: WIRING DIAGRAM - VSX-10 TOASTER COOLING FAN ELEMENT 7 6 BLK MANUAL 4 PILOT LIGHT LIMIT SW MOMENTARY N.C. BLK PUSH BUTTON THERMOSTAT 5 TOP VIEW 3 FRONT SCOTCHLOCK 1 SWITCH MAIN 2 POWER UNUSED WIRE WHITE OR BLUE WIRE ORANGE OR RED FROM CORD 240V 60HZ ORANGE BLACK OR BROWN WIRE 208V 60HZ RED BLK FROM CORD GREEN WIRE FROM CORD CONVEYOR MOTOR FIGURE 10: WIRING DIAGRAM - VSX-20 TOASTER COOLING FAN 5 8 4 ELEMENT 2 1 SSR MANUAL RELAY 4 3 LIMIT SW - +
Краткое содержание страницы № 14
11 43 46 22 45 22 48 32 3 2 47 42 51 5 6 18 1 52 22 50 12 28 21 29 13 19 10 22 55 53 17 23 49 25 34 7 54 9 20 39 10 24 27 37 56 40 14 44 16 36 30 47 33 35 26 81603366 with Supplied 15 41 4 38 31 4 8 9. PARTS LIST & EXPLODED VIEW FIGURE 11: EXPLODED VIEW VSX-10/20 TOASTER 29 VSX-10 VSX-20 14 37 33 47 16 26 39 15 4 8 22 25 23 46 2 31 49 10 13 3 22 50 41 11 48 43 38 45 55 4 51 34 28 47 9 40 1 42 36 54 53 12 19 22 6 24 52 5 10 30 35 20 44 56 27 7 17 22 32 21 18
Краткое содержание страницы № 15
PARTS LIST VSX-10/20 TOASTER ITEM ART P NUMBER DESCRIPTION Used On 1 30201 Terminal Block VSX-20 Indicator Light, Amber 2 56530 VSX-10 Knob, Black 3 56740 VSX-10 Label, CAUTION HOT 4 58081 VSX Solid State Relay 5 69146 VSX-20 6 69147 Thermal Pad for Solid State Relay VSX-20 7 81600025 Bronze Bushing VSX 8 81600050 VSX Bun Thickness Knob 9 81600204 Motor Mount Bracket VSX 10 81600223 Plain Bearing VSX 11 81600224 Keeper Plate for Bearing VSX 12 Drive Chain #25 x 26.75" Lg. 81600235 VSX-20 13 8160
Краткое содержание страницы № 16
10. PROCEDURE FOR CONVEYOR BELT TRACKING Conveyor belt tracking is checked at the . factory New toasters FIGURE 12: should not need adjusting. If, ter af replacing the silicone belt Silicone Belt Tracking Adjustment as described under the periodic maintenance procedure, it begins to "walk" toward one end of the conveyor or , another use the Belt racking T Screw to align the belt to the center of the conveyor (See Figure 13 and age p 19). Keeping the belt centered, along with regular cleaning, s
Краткое содержание страницы № 17
12. PROCEDURE FOR SPLICING THE CONVEYOR CHAIN OOLS T NEEDED: Needle-nose pliers, cord or wire, heavy duty wire cutters, wire ties, pliers, straight edge, safety glasses The Conveyor Chain on your toasters should give you a very long life. ou Y should see very little chain elongation over the life of your . toaster , However if you should have to replace the or conveyor chain remove a link from the , please follow the following instructions. conveyor chain It may be possible that your toaster has
Краткое содержание страницы № 18
1. Begin plicing S In The Center Confirm that the edge s loop are curving back away from the direction of conveyor chain travel as shown in Diagram 1. If not, check to be sure that the conveyor chain is not threaded backwards on the . conveyor Hold the strand up between the two conveyor chain edges and check to see that the edge s loop are going in the same direction as the conveyor s chain edge s. loop (The strand must also be right side up for it to lay flat. uo Y will know immediately
Краткое содержание страницы № 19
Ye CAUTION!!! hand. by Ye Ye Ye the clock- in you YAM If it sprockets screw turn. sprocket, over put half the BT walked to the a has right of need about belt YOU Turn wise the the will center EXTREMELHOT YOURSELF Y. . Right s 2 s i c turn conveyor While sprockets, clock-wise. Left s THE CAUTION!!! 5 the about which is walking Within minutes, sprocket conveyor toward? No sprocket stays walk center belt the minutes? It . the Neither in 5 . Did off in s s t i s 2 e 5 the the turn T screw wise. spro
Краткое содержание страницы № 20
14. APW WYOTT EQUIPMENT LIMITED ARRANTY W APW yott W Foodservice Equipment Company warrants it ’s equipment against defects in materials and workmanship, subject to the following conditions: This warranty applies to the original owner only and is not assignable. Should any product fail to function in its intended manner under normal use within the limits defined in this , warranty at the option of APW yott W such product will be repaired or replaced by APW yott W or its Authorized Service . Agen
