Краткое содержание страницы № 1
Owner’s Manual
ROTARY TOOL KIT
Model No.
PT302H
! WARNING
Always have one hand
firmly placed on the
tool body while
operating. Never
operate the tool by
holding only the tool
handle.
CAUTION: Safety Instructions
Before using this Rotary
Accessories
Tool, read this manual and
Assembly
follow all its Safety Rules
Operation
and Operating Instructions.
Maintenance
FANTOM, 178 West Service Road, Champlain, N.Y. 12919
Краткое содержание страницы № 2
TABLE OF CONTENTS SECTION PAGE SECTION PAGE Product Specifications …………………. 2 Carton Contents ………………………… 6, 7 Power Tool Safety ..…………………….. 3 Know Your Rotary Tool …………..….. .... 8 Rotary Tool Safety .….................…... 4 Assembly & Operation …….…………… 9 – 17 Electrical Requirements & Safety …….. 5 Maintenance …………………………….. 17 Warranty ….....................................……. 18 ! WARNING Some dust created by power sanding, sawing, grinding, drilling and other construction activities c
Краткое содержание страницы № 3
POWER TOOL SAFETY GENERAL SAFETY RULES Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing and gloves ! WARNING away from moving parts. Loose clothing, jewelry or long Read and understand all instructions. Failure to follow hair can be caught in moving parts. all instructions listed below may result in electric shock, fire and/or serious personal injury. Avoid accidental starting. Be sure switch is OFF before plugging in. Carrying tools with your fi
Краткое содержание страницы № 4
ROTARY TOOL SAFETY Always wear safety goggles and dust mask. Use only in well SERVICE ventilated area. Using personal safety devices and working in a Tool service must be performed only by qualified personnel. safe environment reduces risk of injury. Service or maintenance performed by unqualified personnel ALWAYS WEAR EYE PROTECTION. Any power tool could result in risk of injury. can throw foreign objects into your eyes When servicing a tool, use only identical replacement parts. which could ca
Краткое содержание страницы № 5
ELECTRICAL REQUIREMENTS & SAFETY DOUBLE INSULATION GUIDELINES FOR EXTENSION CORDS Make sure your extension cord is in good condition. This cutting tool is double insulated to protect you from When using an extension cord, be sure to use one heavy electrical shock. enough to carry the current the tool will draw. An undersized cord will cause a drop in line voltage resulting ! WARNING in loss of power and overheating. The table below shows the correct size to use according to cord length and Doubl
Краткое содержание страницы № 6
ACCESSORIES CARTON CONTENTS AVAILABLE ACCESSORIES UNPACKING AND CHECKING CARTON CONTENTS ! WARNING ! WARNING Use only accessories recommended for this rotary tool. If any part is missing or damaged, do not plug the Follow instructions that accompany accessories. Use Rotary Tool into the power source until the missing or of improper accessories may cause injury to the damaged part is replaced and assembly is complete. operator or damage to the rotary tool. Carefully unpack the Rotary Tool and al
Краткое содержание страницы № 7
CARTON CONTENTS ROTARY TOOL COMPONENTS KEY DESCRIPTION QTY A Rotary Tool 1 B Precision Handle with Sole Plate 1 C Freehand Sole Plate Attachment 1 D Circle Cutter Attachment 1 E Circle Cutter Installation Adapter 1 F Router Base Attachment 1 G1/8” Collet 1 H1/4” Collet 1 1/8” Lateral Style Drywall Cutter has I "000028 HSS 1/8" marked on the shank 2 of cutter 1/8” General Purpose Cutter has J 2 "000032" marked on the shank of cutter K Straight Router Bit 1 L Round Groove Router Bit
Краткое содержание страницы № 8
KNOW YOUR ROTARY TOOL 8
Краткое содержание страницы № 9
ASSEMBLY & OPERATION ! WARNING Remove the plug from the power source before INSTALLING CUTTING BITS – Cont’d assembly, changing accessories or cutters and making adjustments. This safety action will help 4. Insert new cutting bit (4) into the collet. prevent accidental starting of the tool which could ! WARNING result in serious injury. Insert the bit all the way into the collet and then 1 1 ON / OFF SWITCH pull it back between / ” and / ”. This creates an 16 8 air space between the motor shaf
Краткое содержание страницы № 10
ASSEMBLY & OPERATION CHANGING COLLET INSERT INSTALLING FREEHAND SOLE PLATE – cont’d The cutting bits for this tool are locked into place with a 1. Remove accessory locking knob (1) from the base of collet nut (1) and collet (see Fig. 3). The tool is the spin saw motor housing (see Fig. 4). Slide 1 assembled at the factory with a / ” collet (2) which is used freehand sole plate mounting bracket (2) onto the 8 to hold the cutting bit. An additional ¼” collet (3) is bottom of motor housing (3) u
Краткое содержание страницы № 11
ASSEMBLY & OPERATION PRACTICE CUTS USING FREEHAND SOLE PLATE ! WARNING 6. Turn the switch ON. Have you read “POWER TOOL SAFETY”, “ROTARY 7. When the motor is up to full speed, slowly tip the tool TOOL SAFETY” and “ELECTRICAL SAFETY” on to an upright position, letting the bit cut into the pages 3, 4 and 5 of this Manual? If not, please do it workpiece (see Fig. 7). Once the tool has reached now before you operate this ROTARY TOOL. Your the upright position and the bit has cut through the safe
Краткое содержание страницы № 12
ASSEMBLY & OPERATION CUTTING OUTLET OPENINGS IN DRYWALL CUTTING OUTLET OPENINGS IN DRYWALL – cont’d 6. Move the bit slowly to the right until you feel and hear ! DANGER the bit contacting the inside of the box. Do not attempt to use this tool to make cut-outs around any fixture or opening which has live electrical 7. Pull the bit out far enough to slip it over the edge of wires or on any wall which may have electrical wiring the box. Once the bit is outside the box, push it back behind it. If
Краткое содержание страницы № 13
ASSEMBLY & OPERATION ADJUSTING FREEHAND SOLE PLATE – Cont’d PRECISION HANDLE INSTALLING PRECISION HANDLE The precision handle is designed for use when precision control over the tool movement is desired. The comfortable handle can be used with either the right or left hand. Fig. 11 1. Remove accessory locking knob (1) from the base of the Rotary Tool motor housing (see Fig. 10). Slide CIRCLE CUTTER precision handle mounting bracket (2) onto the bottom of motor housing (3) until the mounting ho
Краткое содержание страницы № 14
ASSEMBLY & OPERATION CIRCLE CUTTER CIRCLE CUTTER OPERATION CIRCLE CUTTER OPERATION – cont’d 5. Turn the switch ON. ! WARNING Unplug the tool from the power source before 6. When the motor is up to full speed, slowly tip the tool changing accessories, changing bits and making and circle cutter assembly to an upright position, adjustments. letting the bit cut into the workpiece (see Fig. 14). Be careful to keep the pivot point located at the center of Before turning the tool ON, check to make sur
Краткое содержание страницы № 15
ASSEMBLY & OPERATION SETTING ROUTER DEPTH ROUTER BASE The router accessory converts your Rotary Tool into a Depth of cutting is controlled by sliding the router base up small hobby router that is capable of handling small ¼” and down in the adjusting sleeves. shank router bits as well as the spiral cutting bit. The tilting base is ideal for bevel cutting. 1. Loosen both height adjusting knobs (1) by turning them counter clockwise (see Fig. 16). ! WARNING 2. Slide router base (2) up or down to
Краткое содержание страницы № 16
ASSEMBLY & OPERATION ROUTER BASE FREEHAND CUTTING AND ROUTING CUTTING STRAIGHT LINE WITH STRAIGHT EDGE When the router base accessory is installed on the To cut a straight line, you can use a straight edge Rotary Tool, it will function as a small router to be used for template to guide the router base. freehand cutting of irregular shaped patterns. You can cut patterns out of the workpiece with the cutting bit or route 1. Draw a line on the workpiece where you wish to make patterns into the wor
Краткое содержание страницы № 17
OPERATION & MAINTENANCE MAINTENANCE ROUTER BASE CUTTING CURVED LINE WITH A TEMPLATE EXTERNAL CLEANING To cut a curved line, you can use a curved template to ! WARNING guide the router base. DO NOT use solvents when cleaning plastic parts. 1. Make a template from hardboard or other similar Most plastics are susceptible to damage from various material to the shape you require (see Fig. 20). types of commercial solvents and may be damaged by NOTE: Radius of curve must be greater than 2 ½” for their
Краткое содержание страницы № 18
Model PT302H TWO (2) YEAR LIMITED WARRANTY FANTOM warrants this product to be free from defects in material and workmanship for a period of two (2) years from the date of the original purchase, when utilized for normal household use, subject to the following conditions, exclusions and exceptions. If your appliance fails to operate properly while in use under normal household conditions within the warranty period, return the complete appliance and accessories, freight prepaid to FANTOM, 178 W. Se
