Руководство по эксплуатации InFocus CR 18DMR

Краткое содержание страницы № 1

Cordless Reciprocating Saw
CR 18DMR

HANDLING INSTRUCTIONS

Read through carefully and understand these instructions before use.

Краткое содержание страницы № 2

12 5 2 4 1 3 6 2 1 1 1 34 8 7 7 9 9 8 56 0 A 0 78 B B C C 910 0 B 0 1

Краткое содержание страницы № 3

11 12 0 F E D 0 C 13 14 0 H B G 15 16 I K JJ J 17 18 O L L N M 19 20 O 2

Краткое содержание страницы № 4

21 22 23 24 25 26 27 28 29 30 P 3 mm 11.5 mm 3

Краткое содержание страницы № 5

31 32 33 Q R S 1 Rechargeable battery 2 Latch 3 Pull out 4 Insert 5 Handle 6 Push 7 Insert 8 Pilot lamp 9 Hole for connecting the rechargeable battery 0 Lever A Front cover B Blade C Plunger slit D Another blade E Blade holder F Machine oil G Rubber Cap H Blade hole I Hexagonal bar wrench J Base K Set screw 12 mm L Lock-off button M Free N Lock O Stroke P Wear limit Q Nail of carbon brush R Protrusion of carbon brush Contact portion outside brush tube S 4

Краткое содержание страницы № 6

° ° ° ° 5

Краткое содержание страницы № 7

12 3 4 1 2 3 4 6

Краткое содержание страницы № 8

7

Краткое содержание страницы № 9

° ° ° ° °


8

Краткое содержание страницы № 10

9

Краткое содержание страницы № 11

10

Краткое содержание страницы № 12

11

Краткое содержание страницы № 13

12

Краткое содержание страницы № 14

° 13

Краткое содержание страницы № 15

23. Do not touch movable parts or accessories unless GENERAL OPERATIONAL PRECAUTIONS the battery has been removed. 24. Always charge the battery before use. 1. Keep work area clean. Cluttered areas and benches 25. Never use a battery other than that specified. Do not invite accidents. connect a usual dry cell, a rechargeable battery other 2. Avoid dangerous environment. Don’t expose power than that specified or a car battery to the power tool. tools and charger to rain. Don’t use power tools 2

Краткое содержание страницы № 16

SPECIFICATIONS POWER TOOL Model CR18DMR 1 - No-Load Speed 0 – 2100 min Stroke 28 mm Capacity Mild Steel Pipe: O.D. 90 mm Vinyl Chloride Pipe: O.D. 90 mm Wood: Depth 90 mm Mild Steel Plate: Thickness 10 mm EB1820L Ni-Cd battery, 18 V (2.0 Ah 15 cells) Rechargeable battery EB1826HL Ni-MH battery, 18 V (2.6 Ah 15 cells) EB1830HL Ni-MH battery, 18 V (3.0 Ah 15 cells) Weight 3.8 kg CHARGER Model UC24YFA UC18YG Charging voltage 7.2 – 24 V 7.2 – 18 V Weight 0.6 kg 0.3 kg STANDARD ACCESSORIES 3 12 4 CR1

Краткое содержание страницы № 17

1. Connect the charger’s power cord to a receptacle BATTERY REMOVAL/INSTALLATION When the power cord is connected, the charger’s pilot lamp will blink in red (At 1-second intervals). CAUTION 2. Insert the battery into the charger Be sure to keep the switch turned off and the lock- Firmly insert the battery into the charger till it off button moved to right position (lock position) contacts the bottom of the charger and checking (See Fig. 17). the polarities as shown in Fig. 3. 1. Battery removal

Краткое содержание страницы № 18

(2) Regarding recharging time Regarding electric discharge in case of new batteries, Depending on the combination of the charger and etc. batteries, the charging time will become as shown As the internal chemical substance of new batteries in Table 5. and batteries that have not been used for an extended period is not activated, the electric Table 5 Charging time (At 20°C) discharge might be short when using them the first Charger and second time. This is a temporary phenomenon, UC18YG Battery a

Краткое содержание страницы № 19

(1) Turn on and off the switching trigger several times NOTE so that the lever can jump out of the front cover Continued use of the tool without cleaning and completely. Thereafter, turn off the switch and lubricating the area where the saw blade is installed remove the battery (Fig. 5). can result in some slack movement of the lever due CAUTION to accumulated sawdust and chips. Under the Be absolutely sure to keep the switch turned off circumstances, pull a rubber cap provided on the and the ba

Краткое содержание страницы № 20

(2) Trigger switch do so, the blade can easily be damaged when it This tool is equipped with a variable speed controlled collides with the material. trigger switch. The tool can be turned "ON" or "OFF"
Make absolutely sure that you cut slowly while by squeezing or releasing the trigger. The blade holding the body firmly. If you apply any plunger stroke rate can be adjusted from the unreasonable force to the saw blade during the minimum to maximum nameplate stroke rate by cutting operation, the