Краткое содержание страницы № 1
IDE 4000 Flash Disk
1.8" and 2.5"
Product Specification and User Manual
January 2005
34-PS-0304-00 Rev. 2.1
Краткое содержание страницы № 2
DOCUMENT CONTROL INFORMATION DCO No.: Title Name Date Issued by: VP Marketing, Embedded Division Ofer Tsur January 5, 2005 REVISION HISTORY Revision Date Description Reference 2.0 June 7, 2004 Added information for new 1.8” form factor -- Updated available capacity information Section 1.2.8 Updated reliability information Section 1.2.9 2.1 January 2, 2004 Updated supported temperature ranges Sections 1.3.1, 9 Update CHS settings information Section 1.2.8 2 Product Specific
Краткое содержание страницы № 3
TABLE OF CONTENTS 1. Specifications........................................................................................................................5 1.1. Critical Item Definition ....................................................................................................5 1.2. Characteristics................................................................................................................5 1.2.1. Interface Definition........................................
Краткое содержание страницы № 4
8. Warranty...............................................................................................................................21 9. Ordering Information ..........................................................................................................22 How to Contact Us ....................................................................................................................23 4 Product Specification and User Manual IDE 4000 Flash Disk 34-PS-0304-00 Rev.
Краткое содержание страницы № 5
1. SPECIFICATIONS 1.1. Critical Item Definition The dimensions of the IDE 4000 flash disk enable mounting in a standard 2.5”or 1.8” disk drive bay, as described in Section 1.2.11. Note: The information written in this document refers to both IDE 4000 2.5” and 1.8” unless otherwise stated. 1.2. Characteristics 1.2.1. Interface Definition The IDE 4000 supports the commands listed in Section 4, in compliance with ATA4 standards. 1.2.2. IDE Transfer Modes The IDE 4000 supports the fo
Краткое содержание страницы № 6
Figure 1: IDE 4000 Performance Results 1.2.4. Access Time Standby to active (typical.): 0.1 msec 1.2.5. Seek Time The IDE 4000 has no seek time, as it has no moving parts. 1.2.6. Input Voltage The IDE 4000 input voltage is 3.3VDC to 5.0VDC. 1.2.7. Current Consumption The current consumption at an input voltage of +5 VDC is described in Table 2. Table 2: IDE 4000 Input Current Consumption with +5 VDC Input Voltage Function/Mode Current (max) mA DC Read 23.0 Write 23.0 Idle/Sl
Краткое содержание страницы № 7
The current consumption at an input voltage of +3.3 VDC is described in Table 3. Table 3: IDE 4000 Input Current Consumption with +3.3VDC Input Voltage Function/Mode Current (max) mA DC Read 16.0 Write 16.0 Idle/Sleep < 1 1.2.8. Memory Capacity As of software version 1.09, the changes listed in Table 4 apply to the CHS (Cylinder, Heads, Sectors) settings for the IDE 4000, capacities 128MB to 512MB (there are no changes for other capacities). Table 4: CHS Settings for Low-Capacity
Краткое содержание страницы № 8
1.2.9. Endurance The IDE 4000 provides 2,000,000 write/erase cycles and an unlimited number of read cycles. Performance is enhanced by the following features: • Wear-Leveling Algorithm: This algorithm guarantees the use of all flash components at the same level of the write/erase cycle. • EDC/ECC (Error Detection Code/Error Correction): The enhanced Reed-Solomon EDC/ECC extends disk endurance by detecting and then fixing flash blocks. 1.2.10. Mean Time Between Failures (MTBF) Tabl
Краткое содержание страницы № 9
Recommended Tightening Tourqe is 6.0 in-lb (0.675 N-m) Recommended Tightening Tourqe is 6.0 in-lb (0.675 N-m) Figure 2: IDE 4000 2.5” Assembly Figure 3: IDE 4000 1.8” Assembly Notes: 1. All dimensions are in mm [in]. 2. General tolerance is ±0.25 mm [±0.01 in]. 9 Product Specification and User Manual IDE 4000 Flash Disk 34-PS-0304-00 Rev. 2.1
Краткое содержание страницы № 10
1.2.11.3 Connector Interface The pinout for the IDE 4000 interface connector is detailed in Table 9 and in Figure 4. Table 9: J1 Pin Assignment Pin Number Signal Name Pin Number Signal Name 1 RESET- 2 GND 3 HD7 4 HD8 5 HD6 6 HD9 7 HD5 8 HD10 9 HD4 10 HD11 11 HD3 12 HD12 13 HD2 14 HD13 15 HD1 16 HD14 17 HD0 18 HD15 19 GND 20 KEY 21 N.C. 22 GND 23 HIOW- 24 GND 25 HIOR- 26 GND 27 IORDY 28 CSEL 29 N.C. 30 GND 31 INTRQ 32 IOCS16- 33 HA1 34 PDIAG- 35 HA0 3
Краткое содержание страницы № 11
Figure 4: IDE 4000 Pin Configuration 1.3. Environmental Conditions The IDE 4000 meets the performance requirements specified below, after exposure to non-operating environmental conditions, or during and after exposure to operating environmental conditions. 1.3.1. Temperature 1.3.1.1 Operating The IDE 4000 operates without degradation at a pressure of 1 atm over the following ambient temperature range: • Commercial temperature version: 0 °C to +70 °C : for IDE 4000 2.5” and 1.8”
Краткое содержание страницы № 12
1.3.1.3 Airflow Requirements General airflow guideline: 3-5 cu.feet/min. 1.3.2. Altitude The IDE 4000 sustains full operation at altitudes ranging from sea level to 80,000 feet above sea level. It is also capable of full operation during air transportation via non-pressurized flights at altitudes greater than 80,000 feet above sea level. 1.3.3. Relative Humidity The IDE 4000 withstands conditions of 8% to 95% non-condensing relative humidity (operation and non-operation). 1.3.4. S
Краткое содержание страницы № 13
2. DRIVE CONFIGURATION The IDE 4000 must be configured as shown in Figure 5 before being mounted in the system’s drive bay. Figure 5: IDE 4000 Disk Address Setting by Jumper 13 Product Specification and User Manual IDE 4000 Flash Disk 34-PS-0304-00 Rev. 2.1
Краткое содержание страницы № 14
3. INTERFACE CONNECTORS The IDE 4000 has a 2-mm pitch interface connector located on the rear panel. It accesses the DC power source and the IDE bus through a non-shielded 44-pin flat cable. Figure 6 provides an example of a connector that can be used to interface with this connector, but any compatible connectors may be used. Figure 6: IDE 4000 Interface Connector In order to prevent damage to the disk by connecting the cable with a 180º rotation, ensure that the special plastic
Краткое содержание страницы № 15
4. SUPPORTED IDE COMMANDS The IDE 4000 supports the commands listed in Table 11. Table 11: IDE Commands Command Name Command Code CHECK POWER MODE 98h E5h EXECUTE DEVICE DIAGNOSTIC 90h FORMAT TRACK 50h IDENTIFY DEVICE Ech IDLE 97h E3h IDLE IMMEDIATE 95h E1h INITIALIZE DEVICE PARAMETERS 91h READ BUFFER E4h READ DMA (with retry) C8h READ DMA (without retry) C9h READ MULTIPLE C4h READ SECTOR(S) (with retry) 20h READ SECTOR(S) (without retry) 21h READ LONG 22h 23h READ VERIFY
Краткое содержание страницы № 16
5. CE AND FCC COMPATIBILITY The IDE 4000 complies with the following CE requirements and FCC standards: • FCC Part 15 Class B • EN 55022 Class B, CISPR 22 Class B (MIC) • V-3/2001.04 Class B (Japan), AS/NZS 3548 Class B (Australia/NZ) • BSMI CNS 13438 Class B (Taiwan) • CAN/CSA-CISPR 22-96 Class B (Canada) CFR 47 FCC Class B • EN 55024, EN 61000 (EMC) 16 Product Specification and User Manual IDE 4000 Flash Disk 34-PS-0304-00 Rev. 2.1
Краткое содержание страницы № 17
6. LABEL INFORMATION The outside label contains the following information: 5 5 1 1 6 6 7 7 8 8 2 2 3 3 4 4 9 9 Figure 7: Outside Label 1. CE and FCC logos 2. Product name 3. Unformatted capacity value 4. M-Systems logo 5. Ordering information 6. Serial number, including date code 7. Part number 8. Declaration 9. ESD warning logo and statement 17 Product Specification and User Manual IDE 4000 Flash Disk 34-PS-0304-00 Rev. 2.1
Краткое содержание страницы № 18
7. USING THE IDE 4000 FLASH DISK The IDE 4000 is shipped with the following components: • Warranty certificate indicating M-Systems’ 36-month warranty • Four screws and one jumper, in kit no. 48-PK-001-00 If any of these items is missing, please contact your dealer. 7.1. Unpacking the Drive Before unpacking or handling a drive, take all proper electrostatic discharge (ESD) precautions, including personnel and equipment grounding. Before you begin installing the IDE 4000 in your sy
Краткое содержание страницы № 19
3. Connect a 44-pin ribbon cable between the IDE 4000 and the adapter. Make sure to orient the cable so that pin 1 of the IDE 4000 is connected to pin 1 of the host adapter. 4. Mount the IDE 4000 in a free drive bay. 5. Close the PC cover and power on the PC. The host BIOS sign-on message appears and displays a key sequence to enter the BIOS setup. Set up the BIOS to recognize the IDE 4000. 7.4. Using the IDE 4000 in an MS-DOS-Based Platform After installing the IDE 4000, it must be
Краткое содержание страницы № 20
7.6. How to Get Help If you need technical assistance with the installation and configuration of your IDE 4000, please contact your customer support representative and have the following information available: • Product and serial number of your IDE 4000 • Description of your computer hardware (manufacturer, model, attached devices, etc.) • Description of your IDE host adapter and associated drivers • Description of your software (operating system, version, application software, etc.
