Краткое содержание страницы № 1
Ramsey Electronics Model No. RB1
Got a problem with furry intruders in your yard or garden? Here
is a professional strength repeller designed to send those pesky
critters running with their tails between their legs. A convenient,
nature friendly method of keeping animals away from where you
don’t want them
• Around 4 watts of screaming high frequency audio. Inaudible
to humans, but a terror to animals.
• 3 settings for different levels of coverage
• Built-in piezo high efficiency
Краткое содержание страницы № 2
PARTIAL LIST OF AVAILABLE KITS RAMSEY TRANSMITTER KITS • FM25B FM Stereo Transmitter • AM1 AM Transmitter • TV6 Television Transmitter • FM100B Professional FM Stereo Transmitter RAMSEY RECEIVER KITS • FR1 FM Broadcast Receiver • AR1 Aircraft Band Receiver • SR2 Shortwave Receiver • AA7 Active Antenna • SC1 Shortwave Converter RAMSEY HOBBY KITS • SG7 Personal Speed Radar • SS70A Speech Scramb
Краткое содержание страницы № 3
Ramsey Publication No. MRB1 Price $5.00 KIT ASSEMBLY AND INSTRUCTION MANUAL FOR RB1 RAT BLASTER TABLE OF CONTENTS Introduction .....................................4 How Does It Work? .........................5 Learn As You Build .........................6 Parts List .........................................7 Parts Layout Diagram .....................8 Construction ....................................9 Schematic Diagram ......................10 Initial Testing ..................
Краткое содержание страницы № 4
INTRODUCTION TO THE RB1 RAT BLASTER This is a practical project for people with problems with furry intruders in their yard, not just rats. The Rat Blaster is useful in repelling all kinds of wildlife. The list includes deer, dogs, cats, all rodents, and even some insects. This is the safest, most effective way to repel animals from eating your shrubbery or burrowing in your carrot patch. It is also a great help at keeping little surprises out of your lawn left by the neighbor’s pets. I
Краткое содержание страницы № 5
HOW DOES IT WORK? Here is where we get into a little circuit analysis. If you just want to plug it in and start scaring off critters, you can skip this section. Otherwise here is some insight into why and how this RB1 works. We will use the schematic located at the center of the manual to analyze the circuit. We will begin with the IC marked NE555, U1. This is a simple, free running oscillator circuit which is used to generate the lower frequency warble rate of the signal. This rate var
Краткое содержание страницы № 6
NOTE TO NEWCOMERS: If you are a first time kit builder you may find this manual easier to understand than you may have expected. Each part in the kit is checked off as you go, while a detailed description of each part is given. If you follow each step in the manual in order, and practice good soldering and kit building skills, the kit is next to fail-safe. If a problem does occur, the manual will lead you step by step through the troubleshooting guide until you find the problem and are ab
Краткое содержание страницы № 7
RAMSEY RB1 PARTS LIST Semiconductors ❒ 1 4001 Quad dual input NOR gate (U3) ❒ 1 XR-2209 voltage controlled oscillator (U2) ❒ 1 NE555 timer (U1) ❒ 2 2N3904 NPN transistors (TO92 package marked 3904) (Q3,4) ❒ 2 221-334 PNP transistors (Flat TO92 package marked 221-334) (Q1,2) ❒ 1 1N4002 rectifier diode (D1) ❒ 1 Large red LED (D2) Resistors ❒ 4 6.2 ohm resistors [blue-red-gold](R12,R13,R14,R15) ❒ 1 2.2K ohm resistor [red-red-red](R16) ❒ 1 3.9K ohm resistor [orang
Краткое содержание страницы № 8
RB1 PARTS LAYOUT DIAGRAM RB1 8
Краткое содержание страницы № 9
CONSTRUCTION OF THE RAT BLASTER: Sort out your parts to begin with, making sure you have all of the parts required. You can use old egg cartons to hold various parts to make them easier to find. We will begin building the kit starting with the lower profile parts to make it easier for us to mount them. You will want to use the parts layout diagram to assist you in finding where the components go. For each part, our word "install" always means these steps: 1. Pick the correct part valu
Краткое содержание страницы № 10
RB1 SCHEMATIC DIAGRAM RB1 10
Краткое содержание страницы № 11
RB1 11
Краткое содержание страницы № 12
❒ 11. Install D1, the 1N4002 power diode. This diode prevents the possibility of someone using the incorrect power supply and inadvertently connecting the power backwards. Make sure the banded end of the diode (cathode) is installed in the same direction as shown in the parts layout diagram. ❒ 12. Install R16, a 2.2K ohm resistor (red-red-red). ❒ 13. Install R1, a 22K ohm resistor (red-red-orange). ❒ 14. Install R12, R13, R14, and R15 all 6.2 ohm resistors (blue-red-gold). ❒ 15.Install R1
Краткое содержание страницы № 13
❒ 23. Install C3, a .1uF disc capacitor (marked .1 or 104). ❒ 24. Install C8, another .1uF disc capacitor (marked .1 or 104). ❒ 25. Install C2, the last .1uF disc capacitor (marked .1 or 104). ❒ 26. It is time to install the transistors, starting with Q3, a 2N3904. Transistors have three legs and must be mounted correctly. Notice that the part has a flat side. Orient the flat side as shown on the parts layout. To install, slide the legs through the circuit board and push the component as
Краткое содержание страницы № 14
Bend the capacitor over so that it is lying down on the board and solder both leads (with the cap lying down you should have plenty of room to solder it in). ❒ 35. Flip the board back over and locate S1, the SPDT power switch. It is the smaller of the two switches and has six leads. Press it firmly into the board and solder all six leads. ❒ 36. Install S2, the 3PDT power setting switch. After pushing firmly into the board, solder all eight connections. ❒ 37. It is now time to install th
Краткое содержание страницы № 15
INITIAL TESTING: ❒ Connect a suitable 12 volt supply to J1- either 12 VAC or 12 VDC ( positive tip). ❒ Set the frequency range switch to LOW. ❒ BEFORE turning on the power, please read the WARNING below (also on the back of the case) WARNING TO ELIMINATE ANY POSSIBLE RISK OF HEARING LOSS, AVOID NEARBY EXPOSURE TO THE “RAT BLASTER” SOUNDS. THIS UNIT CAN CAUSE PERMANENT HEARING DAMAGE. ❒ Turn on the power. The LED should light and you should hear an annoying, high pitched whine. If so,
Краткое содержание страницы № 16
TROUBLESHOOTING GUIDE: If your RB1 does not work at all, recheck the following: ❒ correct orientation of diodes, electrolytic capacitors, ICs and transistors. ❒ resistor color codes; 2.2K and 22K resistors are easily confused. The orange and red color bands look the same under certain conditions. This is also true for 4.7K and 47K resistors. ❒ soldering; solder bridges and cold solder joints are two of the most common problems we see on kits returned for repair. You shouldn’t need a mag
Краткое содержание страницы № 17
USING YOUR RAT BLASTER: Certain animals are affected by different frequency settings and other factors that you can change to repel the pests that are bothering you. The information below should help you get the best results from your Rat Blaster. DOGS: Dogs respond best to the low frequency setting. This is due to the fact that as they age, domestic dogs lose some of their high frequency hearing. (That’s why Old Yeller doesn’t seem to hear me when I whistle for him!?!) CATS: Cats are
Краткое содержание страницы № 18
RB1 18
Краткое содержание страницы № 19
The Ramsey Kit Warranty Please read carefully BEFORE calling or writing in about your kit. Most problems can be solved without contacting the factory. Notice that this is not a "fine print" warranty. We want you to understand your rights and ours too! All Ramsey kits will work if assembled properly. The very fact that your kit includes this new manual is your assurance that a team of knowledgeable people have field-tested several "copies" of this kit straight from the Ramsey inventory. I
Краткое содержание страницы № 20
RB1 Rat Blaster Pest Eliminator Kit Quick Reference Page Guide Introduction ..................................... 4 How Does It Work? ........................5 Learn As You Build .........................6 Parts List ........................................7 Parts Layout Diagram .....................8 Construction ...................................9 Schematic Diagram ......................10 Initial Testing ................................15 Troubleshooting .........................
