Краткое содержание страницы № 1
Ver 2.0
Reference Manual
R FR 5010 / R FR 5011
Series 5000 Rack Frame
© LYNX Technik AG
Brunnenweg 3
64331 Weiterstadt
Germany
www.lynx-technik.com
Series 5000
CardModule
Краткое содержание страницы № 2
Reference Manual R FR 5010 Version1.4 Information in this document is subject to change without notice. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical for any purpose, without express written permission of LYNX Technik AG. LYNX Technik AG may have patents, patent applications, trademarks, copyrights or other intellectual property rights covering the subject matter in this document. Except as expressly written by LYNX T
Краткое содержание страницы № 3
Reference Manual R FR 5010 Version1.4 WARNING Electrical supplies in excess of 50 (fifty) volts peak value are potentially hazardous or lethal. AC supplies between 100 and 250 peak volts exist within the rack frame chassis when connected to AC power. Only qualified personnel should service the rack frame assembly. Removal of technical earth may render the equipment dangerous and intentional removal is prohibited. This unit has to be separated from mains by disconnecting the
Краткое содержание страницы № 4
Reference Manual R FR 5010 Version1.4 WARNUNG! Wenn das Gerät an das Wechselstromnetz angeschlossen ist, treten innerhalb des Gerätes Wechselspannungen zwischen 100 und 250 V auf, die potentiell gefährlich oder tödlich sein können. Deshalb darf Reparatur und Instandhaltung nur von qualifiziertem Personal durchgeführt werden. Das Entfernen des Schutzleiters kann das Gerät in einen gefährlichen Zustand bringen, vorsätzliches Entfernen des Schutzleiters ist verboten. Das Gerät ist
Краткое содержание страницы № 5
Reference Manual R FR 5010 Version1.4 This Page is intentionally left blank Page 5
Краткое содержание страницы № 6
Reference Manual R FR 5010 Version1.4 Warranty LYNX Technik AG warrants that the product will be free from defects in materials and workmanship for a period of two (2) years from the date of shipment. If this product proves defective during the warranty period, LYNX Technik AG at its option will either repair the defective product without charge for parts and labor, or will provide a replacement in exchange for the defective product. In order to obtain service under this warranty, c
Краткое содержание страницы № 7
Reference Manual R FR 5010 Version1.4 Regulatory information Europe Declaration of Conformity We LYNX Technik AG Brunnenweg 3 D-64331 Weiterstadt Germany Declare under our sole responsibility that the product TYPE: R FR 5010 / R FR 5011 To which this declaration relates is in conformity with the following standards (Environments E1-E3): EN 55103-1 /1996 EN 55103-2 /1996 EN 60950 /2001 following the provisions of 89/336/EEC and 73/2
Краткое содержание страницы № 8
Reference Manual R FR 5010 Version1.4 Contents Warranty................................................................................... 6 Regulatory information ........................................................... 7 Europe .............................................................................................. 7 Declaration of Conformity........................................................... 7 USA........................................................................
Краткое содержание страницы № 9
Reference Manual R FR 5010 Version1.4 Electrical Installation. ............................................................31 Installation Instructions..........................................................32 Installations-Anweisung ........................................................33 Settings and Control ..............................................................34 Specifications (R FR 5010 / R FR 5011)..................................35 Available Options....................
Краткое содержание страницы № 10
Reference Manual R FR 5010 Version1.4 Getting Started Packaging The shipping carton and packaging materials provide protection for the module during transit. Please retain the shipping cartons in case subsequent shipping of the product becomes necessary. Product Description The R FR 5010 / R FR 5011 is a high quality 2 RU high 19 inch rack frame enclosure for the LYNX Series 5000 CardModules, designed primarily for broadcast and professional applications. The rack frame can a
Краткое содержание страницы № 11
Reference Manual R FR 5010 Version1.4 board multifunction LED has various states to indicate different alarm conditions and a separate GPO alarm output is provided for connection to an external monitoring system. The system is convection cooled plus forced air- cooling (low noise fans) so it can be used in areas where noise level is critical. Power supplies have a small temperature controlled DC micro fan, which is only used when needed and is also low-noise when operating. The
Краткое содержание страницы № 12
Reference Manual R FR 5010 Version1.4 Rack Layout Figure 2 and 3 shows exploded views of the R FR 5010 / R FR 5011. The Front cover is removed and not shown. Caution : Do not obstruct ventialtion holes on top and bo ttom sides of rack. Refer to mounting instructions for more details. Mounting rails on rear of rack for connection panels Mid Rack Vertical Support CardModule Figure 2. Exploded rack view Page 12
Краткое содержание страницы № 13
Reference Manual R FR 5010 Version1.4 Caution : Do not obstruct ventilation holes on top and bottom sides of rack. Refer to mounting instructions for more details. Controller Mid Rack Vertical Support CardModule Rack mounting Screws Note. Exploded views are shown for reference only It is not necessary to disassemble the rack as shown Figure 3 – Exploded rack view For clarity (to show rack construction) power supplies, rear term
Краткое содержание страницы № 14
Reference Manual R FR 5010 Version1.4 Power Supply The R FR 5010 / R FR 5011 includes the primary power supply. A second identical power supply can be added for redundancy. The Power supply is a sophisticated design designed for critical applications and includes power filtering and integral microprocessor. This monitors the supply operation and reports into the control system. Should a fault develop, the errors are alarmed in the following ways: • Via the LED located on the front
Краткое содержание страницы № 15
Reference Manual R FR 5010 Version1.4 Integral Fan Handle for removal LED Alarm indicator Securing Screw Power Supply seen from Front Figure 4: Power Supply Page 15
Краткое содержание страницы № 16
Reference Manual R FR 5010 Version1.4 Rear Termination Panel The R FR 5010/ R FR 5011 has an integral termination panel on the rear of the rack for the connection of power and various other connections for expansion and interfacing. Figure 5 Figure 5 Rear Panel Connections Rack Connections Power Connection There are two power connections provided for the rack. One is for primary power and the other for the optional redundant power supply. Inp
Краткое содержание страницы № 17
Reference Manual R FR 5010 Version1.4 A stud is provided on the termination panel for the connection of an external ground. (Figure 5) Note: the chassis is permanently grounded via the AC connections. Caution Service to be performed by qualified personnel only ! Caution Please remove power before attempting to exchange a power fuse. Only replace the fuse with a correctly rated replacement. For safety DO NOT physically disconnect or isolate the rack from earth for a
Краткое содержание страницы № 18
Reference Manual R FR 5010 Version1.4 Alarm Function This function requires the controller option. The user can assign triggers for the preferred Major / Minor and No Alarm conditions using the controller and supplied software. The alarm connector provides GPO contacts for 2 alarm levels and a GPI input for future use. This allows for the connection of an external monitoring system. Alarm conditions are triggered by the optional control system and will vary depending on the configur
Краткое содержание страницы № 19
Reference Manual R FR 5010 Version1.4 Extend Connection Bus Extension. This connection is used to interface racks together when using the optional LYNX control system. This is a simple (and inexpensive) way to extend the reach of the host RCT 5020 controller into several more racks fitted with RCT 5010 bus expanders. It uses a proprietary LYNX control interface and this connection is physically daisy chained between all connected racks. Connection details can be seen in the table
Краткое содержание страницы № 20
Reference Manual R FR 5010 Version1.4 Control Connection An external Control Interface is provided on the rear termination panel. When an R CT 5020 Rack Controller (or R CT 5030 Master Controller) is fitted to the rack this port can be used for two primary functions: 1. When configured as a RS 232 serial port this can be connected directly to a PC running the LYNX control software. 2. When configured for RS 422 operation this port is used to daisy chain other racks fitted with R
