Краткое содержание страницы № 1
Toledo q35T S5220
///
Version 1.1
Copyright
Copyright © TYAN Computer Corporation, 2007. All rights reserved. No part of this
manual may be reproduced or translated without prior written consent from TYAN
Computer Corp.
Trademark
All registered and unregistered trademarks and company names contained in this
manual are property of their respective owners including, but not limited to the
following.
TYAN, Toledo q35T are trademarks of TYAN Computer Corporation.
Inte
Краткое содержание страницы № 2
Table of Contents Check the box contents! 3 Chapter 1: Introduction 1.1 Congratulations 5 1.2 Hardware Specifications 5 Chapter 2: Board Installation 2.1 Board Image 8 2.2 Block Diagram 9 2.3 Board Parts, Jumpers and Connectors 10 2.4 Tips on Installing Motherboard in Chassis 20 2.5 Installing the Memory 21 2.6 Installing the Processor and Cooling Fan 23 2.7 Attaching Drive Cables 26 2.8 Installing Add-in Cards 27 2.9 Installing Optional SO-DIMM Modules 28 2.10 Connecting Externa
Краткое содержание страницы № 3
Check the box contents! 1x S5220 motherboard 1 x Ultra-DMA-133/100/66/33 IDE cable 3 x Serial ATA power cables 3x Serial ATA cables 1x USB2.0 cable 1 x S5220 user’s manual 1 x S5220 Quick Reference guide 1 x TYAN driver CD 1 x I/O shield If any of these items are missing, please contact your vendor/dealer for replacement before continuing with the installation process. 3
Краткое содержание страницы № 4
NOTE 4
Краткое содержание страницы № 5
Chapter 1: Introduction 1.1 - Congratulations You have purchased one of the most powerful server solutions available. The ® Toledo q35T (S5220) is a flexible Intel platform for multiple applications, based on ® the Intel Q35 memory Controller Hub (GMCH) and 82801IR I/O Controller Hub (ICH9R) chipsets. ® Designed to support the family of Intel Socket 775 processors and 8GB of DDR2 800/667 memory, the S5220 has integrated Dual Ethernet LAN’s, an integrated graphics controller from Q
Краткое содержание страницы № 6
Memory BIOS • Four 240-pin DDR2 sockets support • Phoenix BIOS on 8Mbit LPC Flash up to 8 GB ROM • Dual channel memory bus (must be • Supports boot from USB device populated in pairs) • Supports ACPI 2.0 • Un-buffered, non-ECC DDR2 667/800 • Power-on mode control for AC power MHz DIMM loss recovery • Supports 256MB, 512MB, 1GB, 2GB DIMM Power Supply • EPS 12V Power Supply (24-pin + 8- System Management pin power connectors) • Total six (6) fan headers with control and tachomet
Краткое содержание страницы № 7
Chapter 2: Board Installation You are now ready to install your motherboard. The mounting hole pattern of the Toledo q35T (S5220) matches the ATX specification. Before continuing with installation, confirm that your chassis supports an ATX motherboard. How to install our products right… the first time The first thing you should do is reading this user’s manual. It contains important information that will make configuration and setup much easier. Here are some precautions you shoul
Краткое содержание страницы № 8
2.1- Board Image Toledo q35T S5220 This picture is representative of the latest board revision available at the time of publishing. The board you receive may or may not look exactly like the above picture. 8
Краткое содержание страницы № 9
2.2 - Block Diagram Toledo q35T S5220 9
Краткое содержание страницы № 10
2.3 - Board Parts, Jumpers and Connectors This diagram is representative of the latest board revision available at the time of publishing. The board you receive may not look exactly like the above diagram. Jumper Legend OPEN - Jumper OFF, without jumper cover CLOSED – Jumper ON, with jumper cover 10
Краткое содержание страницы № 11
Jumper/Connector Function COM2 COM2 Header CPUFAN1, FAN2/3/4/5/6 4-pin Fan Connector with Tachometer USB3/USB4/USB5/USB6 USB Front Panel Connector TYFP1 Front Panel Connector TYFP2/TYFP3 Front Panel Connector for Barebone LCM LCM Connector for Barebone J13 OPMA Connector (supports TYAN M3295) Aux. Power Connector for TYAN Riser Card J24 (M2061) FP-AUDIO Front Panel Audio Connector J35 Reset Switch J36 Power Switch TYFAN/J50/J52 Fan Connector for Barebone Clear CMOS Jumper C
Краткое содержание страницы № 12
CPUFAN1 FAN5 FAN2 FAN3 J24 FAN6 FAN4 TYFP1 LCM 12
Краткое содержание страницы № 13
CPUFAN1/FAN2~FAN6: 4-pin Fan Connector with Tachometer Use these headers to connect the 4-pin cooling fans to your motherboard to keep the system stable and GND 1 reliable. +12V CPUFAN1: J7 FAN2: J6 Tac homet er FAN3: J53 FAN4: J47 PWM C ontrol FAN5: J51 FAN6: J48 These connectors support the tachometer monitoring and auto fan speed control. J24: Aux. Power Connector for TYAN Riser Card (M2061) Pin Signal Pin Signal 1 1 +12V 2 GND 3 GND 4 +5V LCM (J30): LCM Head
Краткое содержание страницы № 14
SATA1 SATA4 SATA2 SATA5 SATA3 SATA6 USB4 FP-AUDIO USB6 COM2 USB5 USB3 14
Краткое содержание страницы № 15
USB3/USB4/USB5/USB6: USB Front Panel Connector PinSignal PinSignal 1 +5V Standby 2 +5V Standby 2 10 3 USB_A- 4 USB_B- 5 USB_A+ 6 USB_B+ 7 GND 8 GND 1 9 9 Key Pin 10 GND USB3: J25 USB5: J21 USB4: J39 USB6: J22 Use these headers to connect to the USB devices via the enclosed USB cable. COM2 (J29): COM2 Header Use these pin definitions to connect a port to COM2. *TYAN does not provide cable for this header. It is designed for
Краткое содержание страницы № 16
TYFP3 J52 J50 TYFAN TYFP2 16
Краткое содержание страницы № 17
TYFP2 (J28) : Front Panel Connector for Barebone It is designed for barebone use only. 11 1 PinSignal PinSignal 1 LAN1 LED+ 2 LAN1 LED- 3 LAN2 LED+ 4 LAN2 LED- 12 2 5 NC 6 NC 7 ID LED+ 8 ID LED- 9 ID SW+ 10 ID SW- 11 Key Pin 12 NC TYFP3 (J31) : Front Panel Connector for Barebone It is designed for barebone use only. 27 1 PinSignal PinSignal 1 HDD LED+ 2 HDD LED- 3 GND 4 RESET- 5 Power LED+ 6 Power LED- 28 2 7 Warning 8 Warning LED+ LED- 9 SMBus Data 10 SMBus Clock 1
Краткое содержание страницы № 18
CMOS 18
Краткое содержание страницы № 19
CMOS (J14): Clear CMOS Jumper Use this jumper when you have forgotten your system/setup 1 password or need to clear the system BIOS settings. 3 How to clear the CMOS data: - Power off system and disconnect the power supply Normal from the AC source (Default) - Use jumper cap to close Pin 2 and 3 for several seconds to Clear CMOS 1 3 - Replace jumper cap to close Pin 1 and 2 Reconnect the power supply to the AC source Clear - Power on system 19
Краткое содержание страницы № 20
2.4 - Tips on Installing Motherboard in Chassis Before installing your motherboard, make sure your chassis has the necessary motherboard support studs installed. These studs are usually metal and are gold in color. Usually, the chassis manufacturer will pre-install the support studs. If you are unsure of stud placement, simply lay the motherboard inside the chassis and align the screw holes of the motherboard to the studs inside the case. If there are any studs missing, you will know ri
