Руководство по эксплуатации Toshiba MK1233GAS

Краткое содержание страницы № 1

TOSHIBA AMERICA INFORMATION SYSTEMS
STORAGE DEVICE DIVISION
IRVINE, CALIFORNIA







MK1233GAS (HDD2A05)
2.5-INCH HARD DISK DRIVE
USER MANUAL








Rev 02
11/2006

Краткое содержание страницы № 2

CONTENTS Introduction..............................................................................1 Setup ........................................................................................2 Using the HDD .........................................................................4 Troubleshooting.......................................................................5 Specifications ..........................................................................6 Drive Connectors......

Краткое содержание страницы № 3

INTRODUCTION - MK1233GAS (HDD2A05) General Features • 2.5" sized drive • 120 Gigabytes * • 9.5mm High • 12ms Average Seek Time • ATA-2,3,4,5,6 Interface • Supports high transfer rates of 100 MB/sec • 8MB Buffer • Rotational speed of 4,200rpm • MTTF 300,000 Hours *Toshiba defines a megabyte (MB) as 1,000,000 bytes and a gigabyte (GB) as 1,000,000,000 bytes. 1

Краткое содержание страницы № 4

SETUP – MK1233GAS (HDD2A05) Caution: Your Hard Disk Drive is a precision device and even a small drop onto any surface can cause damage. Electronstatic discharge can also damage the drive. You should ground yourself prior to handling the drive. Master/Slave Settings Your Toshiba Hard Disk Drive can be configured as either a "Master" or "Slave" unit. Master configuration is used for all single drive applications, and master or slave configuration (only one of each per port) is

Краткое содержание страницы № 5

Placing Hard Drive inside your Computer • Determine mounting configuration (the drive can be mounted in either a horizontal or vertical orientation) • Configure drive for system application. • Configure the adapter board for the specific system application (if required). • Install adapter board into an unused PC/AT 16 bit slot (if required). • Install the I/F cable to the system's 44 pin connector port or adapter board. Ensure pin 1 is oriented correctly, (pin 1 on the cable is us

Краткое содержание страницы № 6

USING THE HARD DISK DRIVE – MK1233GAS (HDD2A05) Backing up Data Files To avoid data loss, regularly back up the data files on the hard disk drive. 4

Краткое содержание страницы № 7

TROUBLESHOOTING – MK1233GAS (HDD2A05) Problem Solution My system is not able to recognize all available capacity There are some systems that are unable to recognize the on my Hard Disk Drive. What do I need to do to utilize new larger Hard Drives on the market. 3rd party software the complete hard drive? is available that breaks the "capacity barrier". Some suggestions are EZ Drive by Micro House and Disk Manager DiskGo by Ontrack. Check with your local computer/software supplie

Краткое содержание страницы № 8

SPECIFICATIONS –MK1233GAS (HDD2A05) General Model MK1233GAS (HDD2A05) Interface ATA-2/3/4/5/6 Functionality Formatted Capacity 120.034GB* Rotational Speed 4200rpm Avg. Rotational Latency 7.14/ms Spin-up Time 4sec (typical) Buffer 8MB Seek Time (Average) 12 Internal Transfer Rate 183.6 ~ 383.2 Mbits/sec (max) Host Transfer Rate 100Mbytes/sec *Toshiba defines a megabyte (MB) as 1,000,000 bytes and a gigabyte (GB) as 1,000,000,000 bytes. Internal Drive Characteristics Num

Краткое содержание страницы № 9

Physical Height 0.37" (9.5mm) Width 2.75" (69.85mm) Depth 3.94" (100mm) Weight 3.46oz (98g) typ Regulatory The drive satisfies the following standards: Underwriters Laboratories (UL) 1950 Canadian Standard Association (CSA) C22.2 No.220 No. 950 TUV Rheinland EN 60 950 EMC - EN50081-1 EN55022: 1988 Class B EN60555-2: 1987+ A1 EN60555-3: 77A (Co) 38 EMC - EN50082-1 IEC 801-2: 1991 EIC 801-3: 1994 IEC 801-4: 1988 7

Краткое содержание страницы № 10

DRIVE CONNECTORS –MK1233GAS (HDD2A05) Figure 1.MK1233GAS HDD Rear View - Connectors Interface Connector Drive Side Connector Yamaichi GAP050K11617 or equivalent Recommended Host Side Connector Board Straight type: Berg 86455-044 86456-044 or equivalent Cable Berg 89361-044 or equivalent Recommended Cable Characteristics Standard diameter 0.32mm (28AWG) Characteristics impedance 100 - 132ohm Max Length 0.46mm (max) Capacitance 35pF (max) * cable is not included wit

Краткое содержание страницы № 11

Interface Pin Assignment DRIVE INTERFACE SIGNALS PIN SIGNAL PIN SIGNAL 1 RESET 2 GROUND 3 DD 7 4 DD 8 5 DD 6 6 DD 9 7 DD 5 8 DD 10 9 DD 4 10 DD 11 11 DD 3 12 DD 12 13 DD 2 14 DD 13 15 DD 1 16 DD 14 17 DD 0 18 DD 15 19 GROUND 20 KEY 21 DMARQ 22 GROUND 23 DIOW/STOP 24 GROUND 25 DIOR/ 26 GROUND -DMARDY HSTROBE 27 IORDY/ 28 CSEL -DMARDY/- DSTROBE 29 DMACK 30 GROUND 31 INTRQ 32 IOCS16 33 DA1 34 PDIAG 35 DA0 36 DA 2 37 CS0 38 CS1 39 DASP 40 GROUND 41 +5V (LOGIC) 42 +5V (