Краткое содержание страницы № 1
AccuSync LCD73V
AccuSync LCD93V
LCD170V
LCD190V
User’s Manual
Краткое содержание страницы № 2
WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION RISK OF ELECTRIC SHOCK • DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS IN
Краткое содержание страницы № 3
For the Customer to use in U.S.A. or Canada Canadian Department of Communications Compliance Statement DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouiller du Canada. C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CSA C22.2 No. 60950-1. Ce produit porte la marque ‘C-UL’ et se conf
Краткое содержание страницы № 4
Contents Your new NEC LCD monitor box* should contain the following: • LCD monitor with tilt base • Power Cord • User’s Manual • CD-ROM • Base Stand • Cable Holder Cable Holder CD-ROM User’s Manual Power Cord Base Stand LCD monitor Captive type (Video signal cable is connected) * Remember to save your original box and packing material to transport or ship the monitor. Quick Start To attach the Base to the LCD Stand: 1. Insert the front of the LCD stand into the holes in the front of the Base (Fi
Краткое содержание страницы № 5
3. Connect the power cord to the power outlet. Place the Video Signal Cable and power cord to the Cable holder (Figure B.1). NOTE: Adjust position of cable that place under the Cable holder to avoid damage for cable or monitor. NOTE: Please refer to Caution section of this manual for proper selection of power cord. 4. Turn on the monitor with the front power button and the computer (Figure C.1). Power Button Cable holder Figure B.1 Figure C.1 5. No-touch Auto Adjust automatically adjusts the mon
Краткое содержание страницы № 6
Non-abrasive surface Figure R.1 Figure R.2 Figure R.3 Removing the Base NOTE: Always remove the Base when shipping the LCD. 1. Place monitor face down on a non-abrasive surface (Figure R.1). 2. While using your thumbs, press the bottom tabs upward to unlock. 3. Pull the unlocked base off the stand. Connecting a Flexible Arm This LCD monitor is designed for use with a flexible arm. Please use the screws (4pcs) as shown in the picture when installing. To meet the safety requirements, the monitor m
Краткое содержание страницы № 7
Controls OSM (On-Screen Manager) control buttons on the front of the monitor function as follows: 1. Basic function at pressing each key SELECT AUTO / RESET – + Button At No OSD Shortcut to Bright adjust Shortcut to contrast adjust “Auto adjust” operate. Showing OSM. showing window. window. At OSD showing Go to Adjustment stage. Cursor goes to left. Cursor goes to right. (Icon selection stage) At OSD showing Go to Icon selection stage. Adjust value decrease or Adjust value increase or Reset oper
Краткое содержание страницы № 8
BRIGHTNESS Adjusts the overall image and background screen brightness. CONTRAST Adjusts the image brightness in relation to the background. AUTO CONTRAST Adjusts the image displayed for non-standard video inputs. AUTO ADJUST Automatically adjusts the Image Position, the H. Size and Fine setting. LEFT/RIGHT Controls Horizontal Image Position within the display area of the LCD. DOWN/UP Controls Vertical Image Position within the display area of the LCD. H. SIZE Adjusts the horizontal size by incre
Краткое содержание страницы № 9
OSM LOCK OUT This control completely locks out access to all OSM control functions without Brightness and Contrast. When attempting to activate OSM controls while in the Lock Out mode, a screen will appear indicating the OSM are locked out. To activate the OSM Lock Out function, press “AUTO/ RESET”, then “+” key and hold down simultaneously. To de-activate the OSM Lock Out, press “AUTO/ RESET”, then “+” key and hold down simultaneously. RESOLUTION NOTIFIER If ON is selected, a message will appea
Краткое содержание страницы № 10
Recommended use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE LCD COLOUR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. • Do not spill any liquids into the cabinet or use your monitor near water. • Do not insert objects of any kind into the cabinet slots, a
Краткое содержание страницы № 11
CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for warm-up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen. • Position your monitor no closer than 40 cm and no further away than 70 cm from your eyes. The optimal distance is 50 cm. • Rest
Краткое содержание страницы № 12
Specifications AccuSync LCD73V Monitor Monitor Specifications AccuSync LCD73V Monitor Notes LCD Module Diagonal: 43 cm/17 inches Active matrix; thin film transistor (TFT) Viewable Image Size: 43 cm/17 inches liquid crystal display (LCD); 0.264 mm dot 2 Native Resolution (Pixel Count): 1280 x 1024 pitch; 270 cd/m white luminance, 500:1 contrast ratio, typical, response time: 8 ms. Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Sync: Separate sync.TTL Level (Positive/Negative) Horizontal sync. Positi
Краткое содержание страницы № 13
Specifications AccuSync LCD93V Monitor Monitor Specifications AccuSync LCD93V Monitor Notes LCD Module Diagonal: 48.3 cm/19 inches Active matrix; thin film transistor (TFT) Viewable Image Size: 48.3 cm/19 inches liquid crystal display (LCD); 0.294 mm dot 2 2 Native Resolution (Pixel Count): 1280 x 1024 pitch; 300 cd/m * white luminance, 700:1 contrast ratio, typical, response time: 8 ms. Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Sync: Separate sync.TTL Level (Positive/Negative) Horizontal sync
Краткое содержание страницы № 14
Specifications LCD170V Monitor Monitor Specifications LCD170V Monitor Notes LCD Module Diagonal: 43 cm/17 inches Active matrix; thin film transistor (TFT) Viewable Image Size: 43 cm/17 inches liquid crystal display (LCD); 0.264 mm dot 2 Native Resolution (Pixel Count): 1280 x 1024 pitch; 300 cd/m white luminance, 500:1 contrast ratio, typical, response time: 8 ms. Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Sync: Separate sync.TTL Level (Positive/Negative) Horizontal sync. Positive/Negative Vert
Краткое содержание страницы № 15
Specifications LCD190V Monitor Monitor Specifications LCD190V Monitor Notes LCD Module Diagonal: 48.3 cm/19 inches Active matrix; thin film transistor (TFT) Viewable Image Size: 48.3 cm/19 inches liquid crystal display (LCD); 0.294 mm dot 2 2 Native Resolution (Pixel Count): 1280 x 1024 pitch; 300 cd/m * white luminance, 700:1 contrast ratio, typical, response time: 8 ms. Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Sync: Separate sync.TTL Level (Positive/Negative) Horizontal sync. Positive/Negat
Краткое содержание страницы № 16
Features Reduced Footprint: Provides the ideal solution for environments requiring superior image quality but with size and weight limitations. The small footprint and low weight allow it to be moved or transported easily from one location to another. Colour Control Systems: Allows you to adjust the colours on your screen and customize the colour accuracy of your monitor to a variety of standards. OSM (On-Screen Manager) Controls: Allow you to quickly and easily adjust all elements of your scree
Краткое содержание страницы № 17
Troubleshooting No picture • The signal cable should be completely connected to the display card/computer. • The display card should be completely seated in its slot. • Check front power Switch and computer power switch should be in the ON position. • Check to make sure that a supported mode has been selected on the display card or system being used. (Please consult display card or system manual to change graphics mode.) • Check the monitor and your display card with respect to compatibility and
Краткое содержание страницы № 18
TCO’03 Congratulations! The display you have just purchased carries the TCO’03 Displays label. This means that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirements in the world. This makes for a high performance product, designed with the user in focus that also minimizes the impact on our natural environment. Some of the features of the TCO’03 Display requirements: Ergonomics • Good visual ergonomics and image quality in ord
Краткое содержание страницы № 19
Manufacturer’s Recycling and Energy Information NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally- friendly products, and always strive to help define and comply with the latest independent standards from agencies such as ISO (International Organisation for Standardization) and TCO (Swedish Trades Union). Disposin