Краткое содержание страницы № 1
MultiSync LCD2080UX+
User’s Manual
Краткое содержание страницы № 2
Index Warning, Caution .................................................................................................... English-1 Declaration .............................................................................................................. English-1 Canadian Department of Communications Compliance Statement ....................... English-2 Declaration of Conformity ....................................................................................... English-2 Contents........
Краткое содержание страницы № 3
WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PL
Краткое содержание страницы № 4
Canadian Department of Communications Compliance Statement DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950. FCC Information 1. Use the attached specified cables with the MultiSync LCD2080UX+ colour monitor so as not to interfere with radio and television reception. (1) The power supply cord you use must have be
Краткое содержание страницы № 5
Contents Your new NEC MultiSync LCD monitor box* should contain the following: • MultiSync LCD2080UX+ monitor with tilt/swivel/pivot/height adjust stand • Power Cord • Video Signal Cable (15-pin mini D-SUB male to DVI-A) • Video Signal Cable (DVI-D to DVI-D cable) • User’s Manual • CD-ROM • Cable Cover Power Cord 15-pin mini D-SUB male to DVI-A Cable Cover User’s Manual DVI-D to DVI-D cable CD-ROM * Remember to save your original box and packing material to transport or ship the monitor. English
Краткое содержание страницы № 6
Quick Start To attach the MultiSync LCD monitor to your system, follow these instructions: 1. Turn off the power to your computer. 2. For the PC or MAC with DVI digital output: Connect the DVI signal cable to the connector of the display card in your system (Figure A.1). Tighten all screws. For the PC with Analog output: Connect the 15-pin mini D-SUB to DVI-A signal cable to the connector of the display card in your system (Figure A.2). For the MAC: Connect the MultiSync Macintosh cable adapter
Краткое содержание страницы № 7
INPUT1 INPUT2 INPUT1 INPUT2 Figure C.2 Figure C.1 NEC-Mitsubishi optional product attachment. Vacation Do not use this connector unless specified. Switch Power Button Figure D.1 Raise and Lower Monitor Screen The monitor may be raised or lowered in either Portrait or Landscape mode. To raise or lower screen, place hands on each side of the monitor and lift or lower to the desired height (Figure RL.1). NOTE: Handle with care when raising or lowering the monitor screen. Figure RL.1 Screen Rotation
Краткое содержание страницы № 8
Tilt Swivel Grasp top and bottom sides of the monitor screen with your Grasp both sides of the monitor screen with your hands hands and adjust the tilt as desired (Figure TS.1). and adjust the swivel as desired (Figure TS.2). Figure TS.1 Figure TS.2 NOTE: Handle with care when tilting the monitor screen. Remove Monitor Stand for Mounting To prepare the monitor for alternate mounting purposes: 1. Disconnect all cables. 2. Place hands on each side of the monitor and lift up to the highest position
Краткое содержание страницы № 9
Controls OSM (On-Screen Manager) control buttons on the front of the monitor function as follows: To access OSM menu, press any of the control buttons (EXIT, , , –, +). To change signal input, press the SELECT button. NOTE: OSM must be closed in order to change signal input. Menu EXIT Exits the OSM controls. Exits to the OSM main menu. Moves the highlighted area left/right to select control menus. CONTROL / Moves the highlighted area up/down to select one of the controls. Moves the bar left/righ
Краткое содержание страницы № 10
FINE (Analog input only) Improves focus, clarity and image stability by increasing or decreasing this setting. If the “Auto Adjust function” and the “H.Size” function do not give you a satisfactory picture setting, a fine tuning can be performed using the “Fine” function. It improves focus, clearity and image stability by increasing or decreasing this setting. For this a Moiré test pattern could be used. If the Fine value is wrongly calibrated, the result would look like on the left drawing. The
Краткое содержание страницы № 11
OFF TIMER: Monitor will automatically power-down when the end user has selected a pre-determined amount of time. Tools 2 LANGUAGE: OSM control menus are available in seven languages. OSM POSITION: You can choose where you would like the OSM control image to appear on your screen. Selecting OSM Location allows you to manually adjust the position of the OSM control menu left, right, down or up. OSM TURN OFF: The OSM control menu will stay on as long as it is use. In the OSM Turn Off submenu, you c
Краткое содержание страницы № 12
Recommended use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE MULTISYNC LCD COLOUR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. • Do not spill any liquids into the cabinet or use your monitor near water. • Do not insert objects of any kind into the cabine
Краткое содержание страницы № 13
CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for warm-up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen. • Position your monitor no closer than 40 cm and no further away than 70 cm from your eyes. The optimal distance is 50 cm. • Rest
Краткое содержание страницы № 14
Specifications Monitor Specifications MultiSync LCD2080UX+ Monitor Notes LCD Module Diagonal: 51 cm/20.1 inches Active matrix; thin film transistor (TFT) liquid Viewable Image Size: 51 cm/20.1 inches crystal display (LCD); 0.255 mm dot pitch; 2 Native Resolution (Pixel Count): 1600 x 1200 250 cd/m white luminence; 400:1 contrast ratio, typical. Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Digital Input: DVI Sync: Separate sync.TTL Level Horizontal sync. Positive/Negative Vertical sync. Positive/N
Краткое содержание страницы № 15
Features ambix Technology: Dual input technology allowing both analog and digital inputs off of one connector (DVI-I) as well as ® additional legacy analog support off of a traditional 15-pin VGA connector. Provides traditional MultiSync technology compatibility for analog as well as DVI-based digital compatibility for digital inputs. DVI-based digital interfaces include DVI-D,DFP and P&D. DVI-I: The integrated interface ratified by the Digital Display Working Group (DDWG) that allows both digit
Краткое содержание страницы № 16
Troubleshooting No picture • The signal cable should be completely connected to the display card/computer. • The display card should be completely seated in its slot. • Check the Vacation Switch should be in the ON position. • Front Power Switch and computer power switch should be in the ON position. • Check to make sure that a supported mode has been selected on the display card or system being used. (Please consult display card or system manual to change graphics mode.) • Check the monitor and
Краткое содержание страницы № 17
Appendix If you need detailed information about the controls, please use the advanced menu. • Turn off your monitor. • Turn on your monitor by pushing the “POWER” and “SELECT” button at the same time for at least one second simultaneously. • You will see the Advanced menu. This menu is larger than the normal OSM. • Turn off and restart your monitor in the normal way. To make an adjustment, ensure that the tag is highlighted, then pre
Краткое содержание страницы № 18
Tag4 Auto Automatically adjusts the Image Position and H. Size settings and Fine settings. (Analog input only) Press “SELECT” to activate Auto Adjustment. H. Position Controls Horizontal Image Position within the display area of the LCD. Press “+” or “-” to adjust. V. Position Controls Vertical Image Position within the display area of the LCD. Press “+” or “-” to adjust. H. Size Adjusts the horizontal size of the screen. (Analog input only) If the “AUTO Adjust function” do not give you a satisf
Краткое содержание страницы № 19
Tag7 Sharpness This is a digital capability for keeping a crisp image at all signal timings. It continuously adjusts to maintain a distinct or soft image as you prefer, and is set independently according to different timings. The number of adjustment steps is different depending on whether the mode is OFF, FULL or ASPECT (1600 x 1200 is OFF Mode). Press “+” or “-” to adjust. Expansion Mode Sets the zoom method. FULL: The image is expanded to 1600 x 1200, regardless of the resolution. ASPECT: The
Краткое содержание страницы № 20
OSM Rotation To switch OSM between Landscape and Portrait modes. Press “+” or “-” to select. Resolution Notifier The optimal resolution is 1600 x 1200. If ON is selected, a message will appear on the screen after 30 seconds, notifying you that the resolution is not set to 1600 x 1200. Press “+” or “-” to select. Factory Preset Selecting Factory Preset allows you to reset all OSM control settings (BRIGHTNESS, CONTRAST, IMAGE CONTROLS, COLOR CONTROL SYSTEM, SHARPNESS, EXPANSION MODE, OFF TIMER, OS
