Краткое содержание страницы № 1
SyncMaster 204B
Install drivers Install programs
Краткое содержание страницы № 2
Notational Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock Power When not used for extended period of time, set your computer to DPMS. If using a screen saver, set it to the active screen mode.
Краткое содержание страницы № 3
Do not use a damaged or loose plug. This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause an electric shock or fire. Use only a properly grounded plug and receptacle. An improper ground may cause electric shock or equipment damage. Insert the power plug firmly so that it does not come loose. A bad connection may cause fire. Do not excessively bend the plug and wire nor pl
Краткое содержание страницы № 4
Installation Be sure to contact an authorized Service Center when installing your set in a location with heavy dust, high or low temperatures, high humidity, and chemical substances, or where it will be operated for 24 hours continuously such as an airport, train station or etc. Failure to do so may cause serious damage to your set. Put your monitor in a location with low humidity and a minimum of dust. Failure to do so may cause an electric shock or fire inside the monit
Краткое содержание страницы № 5
Set down the monitor carefully. The monitor could be damaged or broken. Do not place the monitor face down. The TFT-LCD surface may be damaged. Installing a wall bracket must be done by a qualified professional. Installation by unqualified personnel may result in injury. Always use the mounting device specified in the owner's manual. When installing the product, make sure to keep it away from the wall (more than 10 cm/4 inch ) for ventilation purposes. Poor ven
Краткое содержание страницы № 6
Use the recommended detergent with a smooth cloth. If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth. A dirty connector may cause an electric shock or fire. Make sure to unplug the power cord before cleaning the product. Otherwise, this may cause electric shock or fire. Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth. Do not use any chemicals such as wax, benzene, alcohol, thinn
Краткое содержание страницы № 7
If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord. Then contact the Service Center. The monitor may malfunction, causing an electric shock or fire. Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time. Failure to do so may cause an electric shock or fire. Do not try to move the monitor by pulling only the wire or the signal cable. This may cause a breakdown, electri
Краткое содержание страницы № 8
Do not insert metal objects such as chopsticks, wire and gimlet or inflammable objects such as paper and match into the vent, headphone port or AV ports. It may cause a fire or an electric shock. If an alien substances or water flows into the product, turn the product off, unplug the power connector from the wall outlet and contact Service Center. If you view a fixed screen for an extended period of time, residual image or blurriness may appear. Change the mode to energy save o
Краткое содержание страницы № 9
Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Unpacking Monitor Manual User's Guide, Monitor Driver, Warranty Card Quick Setup Guide Natural Color, MagicTune™, (Not available in all locations) MagicRotation software Cable
Краткое содержание страницы № 10
D-Sub Cable Power Cord Sold separately DVI Cable Set-Bracket Screws (4 EA) Front Opens the OSD menu. Also use to exit the OSD menu or return MENU button [ ] to the previous menu. MagicBright button MagicBright is a new feature providing optimum viewing [] environment depending on the contents of the image you are watching. Currently six different modes are available: Custom, Text, Internet, Game, Sport and Movie. Each mode has its own pre-configured brightness value. You can easily se
Краткое содержание страницы № 11
For documentations or works involving heavy text. 3) Internet For working with a mixture of images such as text and graphics. 4) Game For watching motion pictures such as a game. 5) Sport For watching motion pictures such as a sport. 6) Movie For watching motion pictures such as a DVD or Video CD. >>Click here to see an animation clip When OSD is not on the screen, push the button to adjust Brightness button [] brightness. >>Click here to see an animation clip Adjust buttons Adjust items i
Краткое содержание страницы № 12
1. POWER ON/OFF Switch : Use this button for turn the monitor on and off 2. POWER port : Power cord, plugs into monitor and wall receptacle. DVI IN port : Connect the DVI Cable to the DVI IN port on the back of your monitor. (SOURCE : Digital) : Connect the signal cable to the RGB IN port on RGB IN port the back of your monitor. (SOURCE : Analog)
Краткое содержание страницы № 13
: The Kensington lock is a device used to Kensington Lock physically fix the system when using it in a public place. (The locking device has to be purchased separately. ) For using a locking device, contact where you purchase it. Stand Stopper : Remve the fixing pin on the stand to lift the monitor up and down. Cable Fix Ring: When connecting the cable is finished fix the cables to the Cable Fix Ring. See Connecting the Monitor for further information regarding cable connections.
Краткое содержание страницы № 14
Connecting the Monitor 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2-1. Using the D-sub (Analog) connector on the video card. Connect the signal cable to the RGB IN port on the back of your monitor. 2-2. Using the DVI (Digital) connector on the video card. Connect the DVI cable to the DVI IN port on the back of your monitor. 2-3. Connected to a Macintosh. Connect the monitor to the Maci
Краткое содержание страницы № 15
Using the Stand Removing the base 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3. Remove two screws (A) and then remove the Stand from the LCD monitor. Pivot Stand / Sliding Stand
Краткое содержание страницы № 16
A.Stand Stopper The Auto Rotation may not be supported depend on the monitor model. If you rotate the screen without lifting it to its maximum height, the screen may be damaged because the edge of the screen would hit the floor. Attaching a Base This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface pad. A. Monitor B. Mounting interface pad ( Sold separately ) 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface
Краткое содержание страницы № 17
When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung.com/ (Worldwide) http://www.samsung.com/monitor (U.S.A) http://www.sec.co.kr/monitor (Korea) http://ww
Краткое содержание страницы № 18
This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage http://www.samsung.com/. 5. Monitor driver installation is completed. Installing the Monitor Driver (Manual) Windows XP | Windows 2000 |Windows Me |Windows NT | Linux When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating
Краткое содержание страницы № 19
4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab. 5. Click " " and select " " then click " " button. Update Driver.. Install from a list or.. Next 6. Select " " then click " " and then click " ". Don't search ,I will.. Next Have disk 7. Click the " " button then choose A:(D:\Driver) and choose your monitor model in the Browse model list and click the " " button. Next
Краткое содержание страницы № 20
8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certified MS logo,and this installation doesn't damage your system.The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ 9. Click the "Close" button then click "OK" button continually. 10. Monitor driver installation is completed. ® ® Microsoft Windows 2000 Operating System When you can see "Digital Sign
