Краткое содержание страницы № 1
ELECTRIC COOKTOP+MICROWAVE DRAWER
INSTALLATION MANUAL
SPECIAL WARNING
INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.
IMPORTANT: SAVE THIS INSTALLATION MANUAL FOR LOCAL ELECTRICAL
INSPECTOR’S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CLEARANCES & DIMENSIONS
For SAFETY CONSIDERATIONS do not install a appliance in any combustible cabinetry which is not
in accord with the stated clearances and dimensions on page 2. See Figures 1 and 2.
APPLIANCE MEASUREMENTS
Краткое содержание страницы № 2
INSTALLATION MANUAL APPLIANCE MEASUREMENTS CLEARANCES AND DIMENSIONS • Provide adequate clearances between the appliance and adjacent 3 1 1 / 2 " g la ss a n d combustible surfaces. co n t r o l p a n e l • Dimensions that are shown in Figures 2 and 3 must be used. 2 9 7 /8" Given dimensions provide minimum clearance. There needs w i d t h of u n it to be a 30-inch minimum clearance between the top of the cooking surface and the bottom of upper unprotected wood or 1 5" a u to metal ca
Краткое содержание страницы № 3
INSTALLATION MANUAL IMPORTANT NOTES TO THE INSTALLER IMPORTANT SAFETY INSTRUCTIONS • Read all of the Installation Manual before installing the If the information in this manual is not followed appliance. exactly, a fi re or electrical shock may result causing • Remove all packing material from the drawer and cooktop property damage, personal injury or death. before connecting the electrical supply to the appliance. • Observe all governing codes and ordinances. • ALL APPLIANCES CAN TIP
Краткое содержание страницы № 4
INSTALLATION MANUAL B ADJUSTING ANTI-TIP BRACKET INSTALLATION Measure the thickness of the counter. See Figure 7. Locate the Anti-Tip Bracket on the backside of the appliance. See Figure 8. • Review and plan ahead all safety instructions, cabinet Loosen screws and adjust space between the glass cooktop and clearances and dimensions, power supply placement and bracket to match the counter thickness plus 1/16”. See Figure 9. electrical requirements before installing. Tighten the screws to
Краткое содержание страницы № 5
INSTALLATION MANUAL C INSTALL THE STOP SCREWS F PUSH THE UNIT BACK UNTIL IT HITS THE STOP SCREWS INSTALLED IN STEP “C” See Figure 12. I M P O R T A N T Confirm all cut-out openings and clearances as indicated on page 2 before installing the appliance. These two stop screws prevent the appliance from sliding out of position during S top scr ew operation. Attach the stop screws (supplied in the screw bag) to the installe d right and left sides of the cabinet opening as specified. See Figure
Краткое содержание страницы № 6
INSTALLATION MANUAL National Electrical Codes, ANSI/NFPA No. 70-Latest Edition. I MAKE SURE THE EDGE OF THE COUNTERTOP FITS FLUSH AGAINST THE END OF THE FRONT CONTROL Effective January 1, 1996, the national Electrical Code requires that new, but not existing, construction utilize a four-conductor connec- PANEL. See Figure 15. tion for this appliance class. When installing this appliance in new construction, a mobile home, recreational vehicle or an area where local codes prohibit grounding
Краткое содержание страницы № 7
INSTALLATION MANUAL 3-WIRE CONNECTION POWER CONNECTIONS When local codes permit connecting the cabinet-grounding conduc- This appliance is manufactured with a neutral (white) power supply tor to the neutral (white) wire. wire and a cabinet-connected green grounding wire. 1 Disconnect the power supply. Connect the appliance cable to the junction box through the UL- listed conduit connector. Complete electrical connection according 2 In the junction box connect the appliance and residence
Краткое содержание страницы № 8
INSTALLATION MANUAL MODEL AND SERIAL NUMBER LOCATION BEFORE YOU CALL FOR SERVICE The Rating Plate, including model and serial number, is located on Read the BEFORE YOU CALL and operating instruction sections the faceplate behind the Microwave Drawer front. in your Operation Manual. It may save you time and expense. The list includes common occurrences that are not the result of defective workmanship or materials in this appliance. CARE, CLEANING AND MAINTENANCE Refer to the warranty in you
