Руководство по эксплуатации Dell 1100

Краткое содержание страницы № 1

Remanufacturing Instructions
Dell 1100 / Samsung ML 1610


For Technical Support, please call Memphis, TN at (888) 757-0762 or Nashua, NH at (888) 627-6555.



Reference Information: Oasis Products:
Dell # 3106640 Toner: D3TN1070

Samsung # ML1610 Drum: D3DR305

Wiper Blade: D3WB20

OEM Yields: Fuse

Краткое содержание страницы № 2

3. Using a small flat screw driver, gently pry and remove the end cap from the cartridge (Fig. 3). Fig. 3 4. Remove the two screws that secure the waste bin to the cartridge (Fig. 4). Fig. 4 5. The waste bin is held in place by a post that sits in a slot on the end cap. Push the waste bin up towards the handle to remove the post from the slot on this end cap. Set the waste bin to the side (Fig. 5).

Краткое содержание страницы № 3

6. Remove the two screws that hold the opposite end cap in place (Fig. 6). Fig. 6 7. Use a small flat screw driver to pry up the end cap to remove it (Fig. 7). Set the toner hopper to the side. Fig. 7 8. Remove the two screws that secure the wiper blade to the waste bin (Fig. 8). Fig. 8 Remanufacturing Instructions Technical Support Memphis, TN (888) 757-0762 Dell 1100 / Samsung ML 1610 Nashua, NH (888) 6

Краткое содержание страницы № 4

9. Remove the wiper blade. Clean all residual toner from the waste bin. Inspect the recovery blade. Replace the wiper blade and set the waste bin to the side for reassembly (Fig. 9). Fig. 9 10. Remove the four gears from the side of the toner hopper (Fig 10). Fig.10 11. Remove the PCR by sliding it toward the gear end of the cartridge and lifting the post once clear from the Saddle (Fig. 11). Clean PCR and set aside for Reasse

Краткое содержание страницы № 5

12. Remove the drum and replace during reassembly (Fig. 12). Fig. 12 13. Remove the fill plug and clean out residual toner from the hopper. Using a small flat screw driver, pry up the locking tab that secures the developer roller stabilizer plate (Fig. 13). Fig. 13 14. Lift up the end of the small spring that comes in contact with the developer roller end post, and then remove the stabilizer plate (Fig.14). Fig. 14 ©

Краткое содержание страницы № 6

15. Remove the developer roller and clean with compressed air and a lint free, wax free wipe (Fig.15). Fig. 15 16. Remove the two screws that secure the doctor blade to the toner hopper (Fig. 16). Fig. 16 17. The opposite end of the spring, that rides on the developer roller post, sits in a small notch on the doctor blade. Move the spring to the end of the doctor blade, so not to damage

Краткое содержание страницы № 7

18. Remove the doctor blade, clean thoroughly, and set to the side for reassembly (Fig. 18). Fig. 18 19. Clean the adder roller thoroughly with compressed air, and then clean the toner hopper of all residual toner (Fig. 19). Fig. 19 20. Clean, inspect and replace all components. Add toner and reassemble in reverse order (Fig. 20). Fig. 20 Remanufacturing Instructions Technical Support Memphis, TN

Краткое содержание страницы № 8

Fig. 21 21. Replace or add (starter carts have no fuse) a fuse that is located on the right front corner of the cartridge for the Dell 1100 (Fig. 21). Remanufacturing Instructions Technical Support Memphis, TN (888) 757-0762 Dell 1100 / Samsung ML 1610 Nashua, NH (888) 627-6555 Oasis and You … Succeeding Together! New Hampshire Tennessee Texas Canada (603) 880-3991 (901) 433-0334 (972) 671-1307 (905) 612-9701 (888) 627-6555 Fax: (901)

Краткое содержание страницы № 9

© 1998 Oasis Imaging Products, Inc. Page 9 of 9