ページ1に含まれる内容の要旨
VM8013
Installation and Operation Manual
INT
CH/
DISP
CAT
1 2
RPT RDM
3
DIM 4
DN UP
5 6
SRC PTY
BAND
A/V IN
iPod Menu
Watts Peak
Watts en Crête
Vatios el Máximo
40W x 4
160
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
VM8013 TABLE OF CONTENTS Introduction ..............................................................................................1 Installation ................................................................................................1 Wiring .......................................................................................................3 Front Panel Release ................................................................................4 Remote Control ..........................
ページ4に含まれる内容の要旨
VM8013 ii
ページ5に含まれる内容の要旨
CH/ INT DISP CAT 12 RPT RDM 3 DIM 4 DN UP 5 6 SRC PTY BAND A/V IN iPod Menu VM8013 2. Remove Transport Screws INTRODUCTION Congratulations on your purchase of the Jensen VM8013 Mobile TRANSPORT SCREWS Multimedia Receiver. It’s a good idea to read all of the instructions before beginning the installation. We recommend having your Jensen VM8013 installed by a reputable installation shop. INSTALLATION HALF SLEEVE This unit is designed for installation in cars, trucks and vans with an existing
ページ6に含まれる内容の要旨
VM8013 4. Place the radio in front of the dashboard opening so the wiring can be ISO Installation brought through the mounting sleeve. Follow the wiring diagram This unit has threaded holes in the chassis carefully and make certain all connections are secure and insulated side panels which may be used with the with wire nuts or electrical tape. See “Wiring” on page 3. After original factory mounting brackets of some completing the wiring connections, turn the unit on to confirm operation
ページ7に含まれる内容の要旨
- VM8013 (Blue) WIRING SAT R (Red) Subwoofer Out SAT L (White) Parking/Active Low Level Input (Pink) Camera In (Yellow) Video Out 1 (Yellow) Video Out 2 SAT BUS (Yellow) Fuse (15A) Camera/Active High Level Input (Green/White) + Antenna SWC (Steering Wheel Control) (Requires PAC SWI-PS Interface Adapter) Battery Rear Line out R (Red) Connect the yellow wire to the battery Gray L (White) or 12 volt power source that is always live. This wire MUST be connected for the radio to work. R (Red) Front L
ページ8に含まれる内容の要旨
VM8013 FRONT PANEL RELEASE The front panel release button (4) releases the mechanism that holds the front panel to the chassis. Detaching the Front Panel To detach the front panel, perform the following steps: 1. Press the power button (1) to turn the unit off. 2. Press the front panel release button to flip the panel down. 3. Grasp the right side to release the front panel and then pull it at an angle to remove the right side from the chassis. 4. Store the front panel it in the supplied ca
ページ9に含まれる内容の要旨
VM8013 REMOTE CONTROL The remote control will allow you to Operating Range control the advanced functions of The remote control sensor (19) is located near REMOTE SENSOR the VM8013. the bottom of the front panel, left of the LCD screen. The remote control can operate within a distance of 3~5m. Replacing the Battery When the range of operation of the remote control becomes short or stops functioning, CLEAR replace the battery with a new lithium battery. Be sure to observe the proper polar
ページ10に含まれる内容の要旨
VM8013 Table 1: Remote Control Functions # Button Tuner SAT CD iPod DVD 1 ZOOM Magnify Image 2TITLE Select Video Mode View DVD Title Screen 3 Power Power On Power On Power On Power On Power On Press and hold to Power Off Press and hold to Power Off Press and hold to Power Off Press and hold to Power Off Press and hold to Power Off 4 SETUP Display Setup Menu Display Setup Menu Display Setup Menu Display Setup Menu Display Setup Menu 5 Navigation Arrows Down/Up (Left returns to pre- Down/Up (Left
ページ11に含まれる内容の要旨
VM8013 OPERATION Power Volume Control To increase the volume, turn the VOL/SEL/MENU (rotary encoder) (2) Press the (power) button (1) to turn the unit on. Press and hold the power clockwise. To decrease the volume, turn the rotary encoder counter- button again to turn the unit off. clockwise. When volume is adjusted, the volume level will be shown on the display panel as a number ranging from “0” (lowest) to “40” (highest). 1 SWC Interface (Optional) INT The VM8013 is compatible with PAC (P
ページ12に含まれる内容の要旨
VM8013 Vol Mode The unit automatically saves your changes and exits the audio control Turn the rotary encoder to select “Last” or “Adjust”. menu after five seconds of inactivity. • Last: When the unit is turned on, the volume will resume at the level selected when last turned off. Menu Operation • Adjust: If choosing “Adjust”, use the A-VOL setting to specify a turn-on Press and hold the VOL/SEL/MENU button (2) for more than two seconds volume. to access the menu. Press the VOL/SEL/MENU but
ページ13に含まれる内容の要旨
VM8013 Reset Button The RESET button is located behind the front panel and can only be accessed with the front panel opened. Resetting the unit will erase the time and preset memories. It should only be activated upon initial installation after all wiring is complete, or if there is a malfunction of any of the switches on the unit. In these circumstances, pressing the RESET button (22) will clear the system and return the unit to default operation. 20 22 21 2 9
ページ14に含まれる内容の要旨
VM8013 SATELLITE RADIO OPERATION Displaying the Identification (ID) Code Listeners can subscribe to XM® Radio on the Web by visiting Before you listen to satellite radio, you must subscribe to the service using www.xmradio.com, or by calling (800) 967-2346. Customers should your radio’s identification number. To display the radio ID, press the DISP have their Radio ID ready (see “Displaying the Identification (ID) button three times or use the |<< tuning button (17) to tune to channel “000”
ページ15に含まれる内容の要旨
VM8013 Category Search 3. Turn the rotary encoder again to select the second digit of the desired channel (0 - 9). 1. To access Category Search mode, press the DISP button (7) twice. The 4. Press VOL/SEL/MENU to enter the second number and move to the list of available categories appears on the screen. first position. (Press and hold if channel is only 2 digits and you are ready to tune to the channel.) 01:02 SAT 5. Turn the rotary encoder again to select the first digit of the channel you
ページ16に含まれる内容の要旨
VM8013 RADIO OPERATION Select a Band 1 Press the BAND button (3) to change between three FM and two AM bands. Each band stores up to six preset stations. INT CH/ DISP CAT Tuning 12 RPT RDM Seek Tuning DIM 3 4 DN UP 5 6 Press the TUNE/TRACK >>| or |<< buttons (17) to seek the next/previous SRC PTY 18 station automatically. BAND A/V IN Manual Tuning iPod Menu Press and hold the TUNE/TRACK >>| or |<< buttons (17) to enter Manual tuning mode. Press the buttons again to move the radio frequency n
ページ17に含まれる内容の要旨
VM8013 Automatic Store (AS) Press and hold the button (16) to select six strong stations and store them in the current band using the Auto Store feature. After entering the stations into memory, the unit will automatically stop at each station for five seconds, allowing you to preview each selection. When using the Auto Store feature, the new stations replace any stations already stored in preset memory. NOTE: You can stop the Auto Store function at any time by pressing the button again.
ページ18に含まれる内容の要旨
VM8013 DISC/MP3/WMA PLAYBACK Inserting and Ejecting a Disc Loading a USB Device Insert the USB device into the USB connector (5) on the front of the unit. Press the button (4) to flip the front panel down. Insert a disc, label side The unit will read the files on the USB device automatically. up, into the disc slot (20). To remove the USB device, press the SRC button (6) to switch to another 20 22 21 2 mode and then remove the USB device from the USB connector. Notes on MP3/WMA Play MP3 and
ページ19に含まれる内容の要旨
VM8013 Acceptable Medium Formats NOTE: A file name entered with characters not on the code list may The following formats are available for the media used in this unit. The not play correctly. maximum number of characters used for file name, including the delimiter (".") and three-character extension, are indicated in parentheses. Electronic Shock Protection • ISO 9660 Level 1 (11 characters) • 10 seconds for CD-DA (CDA) • ISO 9660 Level 2 (31 characters) • >45 seconds for MP3 recorded at 44.
ページ20に含まれる内容の要旨
VM8013 Controlling Disc or File Playback 1 Pause INT CH/ DISP Press the 1/>/|| button (8) to suspend playback. Press the 1/>/|| button CAT 12 RPT RDM again to resume playback. DIM 3 4 DN UP Track Select 5 6 SRC PTY Press the TUNE/TRACK >>| or |<< buttons (17) for less than one second to 18 BAND A/V IN advance to the next track/file. The selected track number will appear on the iPod Menu display. NOTE: Press the BAND button on the front panel (3) or remote control (25) to return to the previ
