Bedienungsanleitung AT&T E2662B

Inhaltszusammenfassung zur Seite Nr. 1

91-5676-10-00_E262Manual_R0FEB2704.qxd 2/27/2004 12:41 PM Page 1
User Manual (Part 2)
2.4 GHz Expansion
Handset E262
For use with AT&T
model E2562 / E2662B

Inhaltszusammenfassung zur Seite Nr. 2

91-5676-10-00_E262Manual_R0FEB2704.qxd 2/27/2004 12:41 PM Page 2 You must charge the See pages 2-3 battery and register the STOP! for easy instructions. handset before use. For customer service or product Please also read information, visit our web site at Important Product Information www.telephones.att.com Enclosed in product package. or call 1-800-222-3111. Table of contents Before you begin........................................1 Parts checklist...........................................

Inhaltszusammenfassung zur Seite Nr. 3

91-5676-10-00_E262Manual_R0FEB2704.qxd 2/27/2004 12:41 PM Page 1 Before you begin This cordless telephone operates with If you move out of range during a the maximum power allowed by the phone conversation, you might hear Federal Communications Commission noise or interference. To improve (FCC). Even so, this handset and reception, move closer to the base. E2562 / E2662B base can communicate If you move out of range without over only a certain distance — which pressing OFF, your phone will b

Inhaltszusammenfassung zur Seite Nr. 4

91-5676-10-00_E262Manual_R0FEB2704.qxd 2/27/2004 12:41 PM Page 2 Battery & charger installation After installation, place the handset in the charger and allow the battery to charge for 12 hours before use. You can keep the battery charged by returning the handset to the charger after each use. When battery power is fully depleted, a full recharge takes about 8 hours. LOW BATTERY RDL MENU MEM Low battery indicator Return handset to charger when this symbol flashes. (Handset will beep Press coi

Inhaltszusammenfassung zur Seite Nr. 5

91-5676-10-00_E262Manual_R0FEB2704.qxd 2/27/2004 12:41 PM Page 3 Registering the handset Enter base ID, then press OK. Before using your new handset, you must register it with R the E2562 / E2662B base. During registration, you must ENTER BASE ID enter the 15-digit ID number of the telephone base. To 123456789012345 find this number, go to the base, press MENU, scroll OK < down to select DISPLAY BASE ID, then press OK. The handset provided with your telephone is automatically registered as Ha

Inhaltszusammenfassung zur Seite Nr. 6

91-5676-10-00_E262Manual_R0FEB2704.qxd 2/27/2004 12:41 PM Page 4 Belt clip & optional headset Install belt clip as shown below if desired. For hands-free telephone conversations, you can use any industry standard 2.5 mm headset (purchased separately). For best results use an AT&T 2.5 mm headset. Snap belt clip into notches on side of handset. Rotate and pull to remove. Plug 2.5 mm headset into jack on side of handset (beneath small rubber cap). 4

Inhaltszusammenfassung zur Seite Nr. 7

91-5676-10-00_E262Manual_R0FEB2704.qxd 2/27/2004 12:41 PM Page 5 Quick reference guide For complete instructions, please refer to the manual provided with your E2562 / E2662B telephone. Softkeys Off/Clear Press a softkey to select a menu item During a call, press to hang up. displayed just above the key. While using menus, press to cancel an operation, back up to the previous menu, or exit the menu display. Item 1 Item 2 Item 3 L1/Flash, L2/Flash Press L1 to make or answer a call on line 1.

Inhaltszusammenfassung zur Seite Nr. 8

91-5676-10-00_E262Manual_R0FEB2704.qxd 2/27/2004 12:41 PM Page 6 www.telephones.att.com Copyright © 2004 Advanced American Telephones. All Rights Reserved. AT&T and the Globe Design are trademarks of AT&T Corp., licensed to Advanced American Telephones. Printed in China. Issue 1 AT&T 02/04. 91-5676-10-00