Bedienungsanleitung AT&T E2525

Inhaltszusammenfassung zur Seite Nr. 1

91-5661-20-00.E250.R0.qxd 02/13/1950 19:21 Page 1
User Manual (Part 2)
2.4 GHz Expansion
Handset E250
For use with AT&T models
E2555 • E2525 • E2600B

Inhaltszusammenfassung zur Seite Nr. 2

91-5661-20-00.E250.R0.qxd 02/13/1950 19:21 Page 2 You must charge See page s 2 - 3 batteries and register the hand- S TOP! for easy instructions. set before use. For customer service or product Please also read information, visit our web site at Important Product Information ww w.telephones.att.com Enclosed in product package. or call 1-800-222-3111. Table of contents Before you begin........................................1 Parts checklist.............................................1 Batte

Inhaltszusammenfassung zur Seite Nr. 3

91-5661-20-00.E250.R0.qxd 02/13/1950 19:21 Page 1 Before you begin This cordless telephone operates with If you move out of range during a the maximum power allowed by the phone conversation, you might hear Federal Communications Commission noise or interference. To improve (FCC). Even so, this handset and base reception, move closer to the base. can communicate over only a certain If you move out of range without distance — which can vary with the pressing OFF, your phone will be left locat

Inhaltszusammenfassung zur Seite Nr. 4

91-5661-20-00.E250.R0.qxd 02/13/1950 19:21 Page 2 Battery installation & charging Install batteries as shown, then place the handset in the charger for at least 8 hours before use. You can keep batteries charged by returning the handset to the charger after each use. When battery power is fully depleted, a full recharge takes about 6 hours. LOW BATTERY REDIAL MENU MEM Low battery indicator Return handset to charger to recharge when this symbol flashes. (Handset will beep when battery is low.)

Inhaltszusammenfassung zur Seite Nr. 5

91-5661-20-00.E250.R0.qxd 02/13/1950 19:21 Page 3 Registering the handset Enter base ID, then press OK. Before using your new handset, you must register it with R the base. During registration, you must enter the 15-digit ENTER BASE ID ID number of the telephone base. To find this number, go 123456789012345 to the base, press MENU, scroll down to select DISPLAY OK < BASE ID, then press OK. The handset provided with your telephone is automatically registered as Handset 1. Additional handsets

Inhaltszusammenfassung zur Seite Nr. 6

91-5661-20-00.E250.R0.qxd 02/13/1950 19:21 Page 4 Belt clip & optional headset Install belt clip as shown below if desired. For hands-free telephone conversations, you can use any industry standard 2.5 mm headset (purchased separately). For best results use an AT&T 2.5 mm headset. Snap belt clip into notches on side of handset. Rotate and pull to remove. Plug 2.5 mm headset into jack on side of handset (beneath small rubber cap). 4

Inhaltszusammenfassung zur Seite Nr. 7

91-5661-20-00.E250.R0.qxd 02/13/1950 19:21 Page 5 Quick reference guide For complete instructions, please refer to the manual provided with your telephone. Softkeys Press a softkey to select a menu item displayed just above the key. Off/Clear During a call, press to hang up. Item 1 Item 2 Item 3 While using menus, press to cancel an operation, back up to the previous menu, or exit the menu display. Phone/Flash Press to begin a call, then dial a number. Xfer/Intercom During a call, press to

Inhaltszusammenfassung zur Seite Nr. 8

91-5661-20-00.E250.R0.qxd 02/13/1950 19:21 Page 6 www.telephones.att.com Copyright © 2004 Advanced American Telephones. All Rights Reserved. AT&T and the Globe Design are trademarks of AT&T Corp., licensed to Advanced American Telephones. Printed in China. Issue 2 AT&T 06/04. 91-5661-20-00