Bedienungsanleitung Avaya ALGO-3226-CM

Inhaltszusammenfassung zur Seite Nr. 1

Avaya Solution & Interoperability Test Lab

Application Notes for Algo 3226 Trunk Port FXO

Doorphone with Avaya Aura® Communication Manager
- Issue 1.0






Abstract


These Application Notes describe the steps required to integrate the Algo 3226 Trunk Port
FXO Doorphone with Avaya Aura® Communication Manager. The 3226 Trunk Port FXO
Doorphone provides hands-free intercom capability and entrance security with door unlock
control. The doorphone connects to a loo

Inhaltszusammenfassung zur Seite Nr. 2

1. Introduction These Application Notes describe the steps required to integrate the Algo 3226 Trunk Port FXO Doorphone with Avaya Aura® Communication Manager. The 3226 Trunk Port FXO Doorphone provides hands-free intercom capability and entrance security with door unlock control. The doorphone connects to a loop start trunk port on Communication Manager. The doorphone includes a Control Unit and Door Station. A visitor can press the call button on the Door Station to ring a specified

Inhaltszusammenfassung zur Seite Nr. 3

3. Reference Configuration Figure 1 illustrates a sample configuration with Communication Manager running on an Avaya S8800 Server with a G450 Media Gateway, and the Algo 3226 Trunk Port FXO Doorphone. The doorphone connected to a loop start trunk (MM711 Analog Board) on the G450 Media Gateway. LAN Avaya S8800 Server running Avaya Aura® Communication Manager Avaya 9600 Series SIP and H.323 Telephones Loop Start Trunk Avaya G450 Media Gateway Algo 3226 Trunk Port FXO Doorphone Figur

Inhaltszusammenfassung zur Seite Nr. 4

4. Equipment and Software Validated The following equipment and software were used for the sample configuration provided: Hardware Component Version Avaya S8800 Server and G450 Media Avaya Aura® Communication Manager 6.0.1 Gateway SP 3 (R016x.00.1.510.1 w/Patch 19009) Avaya 9600 Series IP Telephones 3.1 (H.323) 2.6.4 (SIP) Algo 3226 Trunk Port FXO Doorphone 1.04 5. Configure Avaya Aura® Communication Manager This section describes the steps for configuring a loop start trunk for

Inhaltszusammenfassung zur Seite Nr. 5

5.2. Configure Station Use the add station command to add a station for the door attendant that will be called when the call button on the 3226 Doorphone is pressed. The following is a basic H.323 station that was used for this purpose. Other types of stations, like SIP, may also be used. add station 77301 Page 1 of 5 STATION Extension: 77301 Lock Messages? n

Inhaltszusammenfassung zur Seite Nr. 6

Lastly, specify the loop start trunk group in route pattern 100/ change route-pattern 100 Page 1 of 3 Pattern Number: 100 Pattern Name: 3226 Doorphone SCCAN? n Secure SIP? n Grp FRL NPA Pfx Hop Toll No. Inserted DCS/ IXC No Mrk Lmt List Del Digits QSIG Dgts

Inhaltszusammenfassung zur Seite Nr. 7

7. Verification Steps The following steps can be used to verify and/or troubleshoot installations in the field. 1. Verify that the staus of the loop start trunk connected to the 3226 Trunk Port FXO Doorphone is in-service using the status trunk command on Communication Manager. Below is the output of the command. status trunk 100 TRUNK GROUP STATUS Member Port Service State Mtce Connected Ports Busy

Inhaltszusammenfassung zur Seite Nr. 8

©2011 Avaya Inc. All Rights Reserved. Avaya and the Avaya Logo are trademarks of Avaya Inc. All trademarks identified by ® and ™ are registered trademarks or trademarks, respectively, of Avaya Inc. All other trademarks are the property of their respective owners. The information provided in these Application Notes is subject to change without notice. The configurations, technical data, and recommendations provided in these Application Notes are believed to be accurate and dependable