Inhaltszusammenfassung zur Seite Nr. 1
Inhaltszusammenfassung zur Seite Nr. 2
VIVOTEK Table of Contents Overview3 Read Before Use �������������������������������������������������������������������������������������������������������������������������������������3 Package Contents �����������������������������������������������������
Inhaltszusammenfassung zur Seite Nr. 3
VIVOTEK Overview VIVOTEK’s FD8361L is the latest professional-series outdoor fixed dome network camera featuring superb megapixel image quality and exceptional bandwidth efficiency. With day & night functionality and a weatherproof housing, it is especially suitable for tough outdoor surveillance environments such as parking lots and streets� Featuring a 2-megapixel sensor, the FD8361L is able to provide extremely wide coverage with the finest details� Additionally, the camera is incorpor
Inhaltszusammenfassung zur Seite Nr. 4
VIVOTEK Physical Description Inner View IR LEDs (18 units, Vari-focal Lens distance 20m) (f= 3~9 mm) Light Sensor SD/SDHC Card Slot Rotation Adjustment Screw Tilt Adjustment Screw Pan Adjustment Screw NTSC/PAL Video Output Switch Status LED Recessed Reset Button Focus Controller Zoom Controller BNC Video Output General I/O Terminal Block Ethernet 10/100 RJ45 Plug Ground Operating environment: -20° ~ 50°C When the temparature inside the Network Camera reaches over 50°C, the fan will oper
Inhaltszusammenfassung zur Seite Nr. 5
VIVOTEK Outer View c IP66-rated Vandal-proof Dome Cover b a Camera Base IP66-rated Vandal-proof Bottom Base c Record the MAC address under the camera base before Network Camera V I RoHS Model No: FD8361 installing the camera� MAC:0002D1083236 CLASS A This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference
Inhaltszusammenfassung zur Seite Nr. 6
VIVOTEK Hardware Reset SD/SDHC Card Slot Status LED Recessed Reset Button The reset button is used to reset the system or restore the factory default settings� Sometimes resetting the system can return the camera to normal operation� If the system problems remain after reset, restore the factory settings and install again� Reset: Press and release the recessed reset button with a paper clip or thin object� Wait for the Network Camera to reboot� Restore: Press and hold the recessed reset b
Inhaltszusammenfassung zur Seite Nr. 7
VIVOTEK Installation Hardware Installation First, use a screwdriver to loose the three screws and detach the dome cover from the camera base� Then, follow the steps below to install the camera to either a ceiling or a wall� Ceiling mount (with the bottom base) 1� Attach the supplied alignment sticker to the ceiling� 2� Using the 10 circles on the sticker, drill at least 2 pilot holes symmetrically on each side into the ceiling� Then hammer the four supplied plastic anchors into the holes�
Inhaltszusammenfassung zur Seite Nr. 8
VIVOTEK Wall mount (with the bottom base) 1� Attach the supplied alignment sticker to the wall� 2� Using the 10 circles on the sticker, drill at least 2 pilot holes symmetrically on each side into the wall� Then hammer the four supplied plastic anchors into the holes� 3� Using the four holes on the bottom base, insert the four supplied screws to corresponding holes and secure the bottom base with a screwdriver� 4� Feed the cables through hole A or B� If you want to use hole B, remove the
Inhaltszusammenfassung zur Seite Nr. 9
VIVOTEK Drop-ceiling mount (without the bottom base) 1� Attach the supplied ceiling hole template sticker to the ceiling� 2� Open a hole along the inner circle of the sticker� 3� Using the 3 circles on the sticker, drill 3 pilot holes into the ceiling� Then hammer the three supplied plastic anchors into the holes� 4� Mount the Network Camera to the ceiling and feed the cables through� 5� Using the three holes on the side of the camera base, insert the three supplied screws into the corresp
Inhaltszusammenfassung zur Seite Nr. 10
PARTITION PARTITION LINK RECEIVE POWER COLLISION 1 2 3 4 5 LINK RECEIVE POWER COLLISION 1 2 3 4 5 VIVOTEK Network Deployment Setting up the Network Camera over the Internet This section explains how to configure the Network Camera to an Internet connection� 1� Connect the power cable to the AC 24V terminal block� 2. Use the supplied RJ45 female/female coupler to connect the Network Camera to a switch. Use a Category 5 Cross Cable when Network Camera is directly connected to PC� AC24V: Power
Inhaltszusammenfassung zur Seite Nr. 11
VIVOTEK 2� In this case, if the Local Area Network (LAN) IP address of your Network Camera is 192�168�0�3, please forward the following ports for the Network Camera on the router� ■ HTTP port ■ RTSP port ■ RTP port for video ■ RTCP port for video If you have changed the port numbers on the Network page, please open the ports accordingly on your router� For information on how to forward ports on the router, please refer to your router’s user’s manual� 3� Find out the public IP address o
Inhaltszusammenfassung zur Seite Nr. 12
PARTITION PARTITION LINK RECEIVE POWER COLLISION 1 2 3 4 5 LINK RECEIVE POWER COLLISION 1 2 3 4 5 VIVOTEK Set up the Network Camera through Power over Ethernet (PoE) When using a PoE-enabled switch The Network Camera is PoE-compliant, allowing transmission of power and data via a single Ethernet cable� Follow the below illustration to connect the Network Camera to a PoE-enabled switch via Ethernet cable� power + data transmission PoE Switch When using a non-PoE switch If your switch/router
Inhaltszusammenfassung zur Seite Nr. 13
VIVOTEK Software Installation Installation Wizard 2 (IW2), free-bundled software included on the product CD, helps you set up your Network Camera on the LAN� 1� Install IW2 under the Software Utility directory from the software CD� Double click the IW2 shortcut on your desktop to launch the program� 2� The program will conduct an analysis of your network environment� After your network environment is analyzed, please click Next to continue the program� 3� The program will search fo
Inhaltszusammenfassung zur Seite Nr. 14
VIVOTEK Ready to Use 1� Access the Network Camera on the LAN� 2� Retrieve live video through a web browser or recording software� Adjusting the Lens Based on the live image retrieved from the camera, adjust the camera lens by doing the following: To adjust the viewing angle -- 3-axis mechanism design 1� Loosen the pan adjustment screw and then turn the lens module left and right� Upon completion, tighten the screw� 2� Loosen the tilt adjustment screws on both side of the camera and then tur
Inhaltszusammenfassung zur Seite Nr. 15
8 VIVOTEK To adjust the zoom factor and focus range 1� Loosen the zoom controller to adjust the zoom factor� Upon completion, tighten the zoom controller� 2� Loosen the focus controller to adjust the focus range� Upon completion, tighten the focus controller� Loosen W T N Tighten DO NOT over rotate the lens� Doing so will damage the camera lens module Completion 1. Rotate the black cover inside the dome cover to fit the lens shooting direction. 2� Attach the dome cover to camera� 3� Secur
Inhaltszusammenfassung zur Seite Nr. 16
VIVOTEK Accessing the Network Camera This chapter explains how to access the Network Camera through web browsers, RTSP players, 3GPP-compatible mobile devices, and VIVOTEK recording software� Using Web Browsers Use Installation Wizard 2 (IW2) to access to the Network Cameras on the LAN� If your network environment is not a LAN, follow these steps to access the Network Camera: ® 1� Launch your web browser (ex� Microsoft Internet Explorer, Mozilla Firefox, or Netscape)� 2. Enter the IP addre
Inhaltszusammenfassung zur Seite Nr. 17
VIVOTEK ► By default, the Network Camera is not password-protected. To prevent unauthorized access, it is highly recommended to set a password for the Network Camera� For more information about how to enable password protection, please refer to Security on page 30� ® ► If you see a dialog box indicating that your security settings prohibit running ActiveX ® Controls, please enable the ActiveX Controls for your browser� 1� Choose Tools > Internet Options > Security > Custom Level� ® 2. Lo
Inhaltszusammenfassung zur Seite Nr. 18
VIVOTEK Using RTSP Players To view the MPEG-4 streaming media using RTSP players, you can use one of the following players that support RTSP streaming� Quick Time Player Real Player VLC media player 1� Launch the RTSP player� mpegable Player mpegable Player 2� Choose File > Open URL� A URL dialog box will pop up� 3� The address format is rtsp://:/
Inhaltszusammenfassung zur Seite Nr. 19
VIVOTEK Using 3GPP-compatible Mobile Devices To view the streaming media through 3GPP-compatible mobile devices, make sure the Network Camera can be accessed over the Internet � For more information on how to set up the Network Camera over the Internet, please refer to Setup the Network Camera over the Internet on page 10� To utilize this feature, please check the following settings on your Network Camera: 1� Because most players on 3GPP mobile phones do not support RTSP authentication, ma
Inhaltszusammenfassung zur Seite Nr. 20
VIVOTEK Using VIVOTEK Recording Software The product software CD also contains recording software, allowing simultaneous monitoring and video recording for multiple Network Cameras� Please install the recording software; then launch the program to add the Network Camera to the Channel list� For detailed information about how to use the recording software, please refer to the user’s manual of the software or download it from http://www�vivotek�com� 20 - User's Manual
