Inhaltszusammenfassung zur Seite Nr. 1
Bullet
IP8361 Network Camera
User’s Manual
2MP • Outdoor • Day & Night
Cable Management
Rev. 1.1
Inhaltszusammenfassung zur Seite Nr. 2
VIVOTEK Table of Contents Overview 4 Read Before Use .....................................................................................................................................4 Package Contents .....................................................
Inhaltszusammenfassung zur Seite Nr. 3
VIVOTEK Appendix 115 URL Commands for the Network Camera .......................................................................................................... 115 Technical Specifications ..................................................................................................................................... 172 Techn
Inhaltszusammenfassung zur Seite Nr. 4
VIVOTEK Overview VIVOTEK IP8361 is a high-end 2-megapixel network bullet camera surveillance. outdoor-specific features such as concealed wiring to prevent tampering, the IP8361 is the camera of choice for applications such as parking lots, gas stations, and building entrances. The IP8361 boasts high-definition 2-megapixel (1600 x 1200) resolution, allowing for the delivery of extremely detailed images and coverage 6 times larger than a VGA camera. To maximize the benefit of the 2-megapixe
Inhaltszusammenfassung zur Seite Nr. 5
VIVOTEK Revision History Rev. 1.0: Initial release Rev. 1.1: Removed DC power adapter from the package contents; added DO connection diagrams. Symbols and Statements in this Document INFORMATION: provides important messages or advices that might help prevent inconvenient i or problem situations. NOTE: Notices provide guidance or advices that are related to the functional integrity of the machine. Tips: Tips are useful information that helps enhance or facilitae an installation, functio
Inhaltszusammenfassung zur Seite Nr. 6
VIVOTEK Physical Description Lens IR LEDs Light Sensor SD/SDHC/SDXC Card Slot General I/O Terminal Block Reset Button Status LED Power Cord Socket RJ45 Cable General I/O Terminal Block This Network Camera provides a general I/O terminal block which is used to connect external input / output devices. The pin definitions are described below. Pin Name 1 Power +12V 2 Digital Output 3 Digital Input 4 Ground 5 AC 24V Input 1 2 3 4 5 6 7 8 6 AC 24V Input 7 RS-485 + 8 RS-485 - Pin Name 1 External M
Inhaltszusammenfassung zur Seite Nr. 7
VIVOTEK DI/DO Diagram Please refer to the following illustration for the connection method. 12V PIN 1 Power+12V PIN 2 Digital output +12V PIN 3 Digital input PIN 4 Ground Gnd 4 Gnd 4 VDC 1 1 Camera Power VDC Camera Power +12 3 Switch VDC 3 Switch +30 Input Input VDC Max. 2 2 Output Output BJT transistor BJT transistor Relay Relay Status LED The LED indicates the status of the Network Camera. Item LED status Description Steady Red Power on and system booting 1 Red LED Off Power off or power is
Inhaltszusammenfassung zur Seite Nr. 8
VIVOTEK Hardware Reset Reset Button Status LED The reset button is used to reset the system or to restore factory defaults. Sometimes resetting the system can return the camera to normal operation. If the system problems remain after reset, restore the factory settings and install again. Reset: Press and release the recessed reset button with a paper clip or thin object. Wait for the Network Camera to reboot. Restore: Press and hold the recessed reset button until the status LED rapidly b
Inhaltszusammenfassung zur Seite Nr. 9
VIVOTEK Cabling Assembly RJ45 Cable Connector Components of the Waterproof RJ45 Cable Dimension (unit: mm) Connector Sealing Nut (A) Seal (B) Screw Nut (C) Housing (D) Gasket (E) Assembling Steps 2 3 1 Insert the housing into the Insert the seal into the housing. Prepare an Ethernet cable screw nut. and strip part of the sheath. (C) (D) (B) Recommended cable gauge: 24AWG (0.51 mm) Insert the stripped Ethernet 4 5 6 Push the RJ45 plug into the Clamp the cable with cable through the sealin
Inhaltszusammenfassung zur Seite Nr. 10
VIVOTEK Hardware Installation 1. Attach the alignment sticker to the wall. Drill four holes into the wall. Then hammer the supplied plastic anchors into the holes and secure the plate with supplied screws. 2. Fix the intersection bracket to the side of the Network Camera with two screws. 3. Feed the RJ45 cable through the front opening of the wall mount bracket. (If you want to use external devices such as sensors and alarms, please refer to the assembling steps on the next page.) 4. Open t
Inhaltszusammenfassung zur Seite Nr. 11
VIVOTEK Waterproof Connector Components of the Waterproof Connector Pin Definition 1 Power +12V Screw Nut (A) 2 Digital Output Seal (B) 3 Digital Input Seals (C) 4 Ground 1 2 3 4 5 6 7 8 5 AC 24V Housing (D) 6 AC 24V Sealing Nut (E) 7 RS485 + 8 RS485 - 1 External MIC In 2 Ground 3 Audio Out 4 Ground Assembling Steps 1. Disassemble the components of the waterproof connector into part (A) ~ (E) as shown above. 2. Open the back cover of the Network Camera. 3. Remove the rubber stopper from the bo
Inhaltszusammenfassung zur Seite Nr. 12
PARTITION LINK RECEIVE POWER COLLISION 1 2 3 4 5 VIVOTEK Network Deployment Setting up the Network Camera over the Internet There are several ways to set up the Network Camera over the Internet. The first way is to set up the Network Camera behind a router. The second way is to utilize a static IP. The third way is to use PPPoE. Internet connection via a router Before setting up the Network Camera over the Internet, make sure you have a router and follow the steps below. 1. Connect your Net
Inhaltszusammenfassung zur Seite Nr. 13
VIVOTEK Internet connection with static IP Choose this connection type if you are required to use a static IP for the Network Camera. Please refer to LAN on page 41 for details. Internet connection via PPPoE (Point-to-Point over Ethernet) Choose this connection type if you are connected to the Internet via a DSL Line. Please refer to PPPoE on page 42 for details. User's Manual - 13
Inhaltszusammenfassung zur Seite Nr. 14
PARTITION PARTITION LINK RECEIVE POWER COLLISION 1 2 3 4 5 LINK RECEIVE POWER COLLISION 1 2 3 4 5 VIVOTEK Set up the Network Camera through Power over Ethernet (PoE) When using a PoE-enabled switch The Network Camera is PoE-compliant, allowing transmission of power and data via a single Ethernet cable. Follow the below illustration to connect the Network Camera to a PoE-enabled switch via an Ethernet cable. power + data transmission PoE Switch When using a non-PoE switch If your switch/route
Inhaltszusammenfassung zur Seite Nr. 15
VIVOTEK Software Installation Installation Wizard 2 (IW2), free-bundled software included on the product CD, helps you set up your Network Camera on the LAN. 1. Install IW2 under the Software Utility directory from the software CD. Double click the IW2 shortcut on your desktop to launch the program. 2. The program will conduct an analysis of your network environment. After your network environment is analyzed, please click Next to continue the program. 3. The program will search for
Inhaltszusammenfassung zur Seite Nr. 16
VIVOTEK Ready to Use 1. A browser session with the Network Camera should prompt as shown below 2. You should be able to see live video from your camera. You may also install the 32-channel recording software from the software CD in a deployment consisting of multiple cameras. For its installation details, please refer to its related documents. 3. Unscrew the zoom controller to adjust the zoom factor. Upon completion, tighten the zoom controller. 4. Unscrew the focus controller to adjust the
Inhaltszusammenfassung zur Seite Nr. 17
VIVOTEK 5. Tighten the lens cover. 6. Open the back cover. 7. Tear down the aluminum foil vacuum bag and take out the silica gel. Attach the silica gel to the inner side of the back cover, then tighten the back cover. (Please replace the silica gel desiccant with a new one if you open the back cover after installation.) 6 7 5 NOTE: If you want to use the supplied sun shield for outdoor environments, please follow the steps below to install: 1. Tighten the supplied two coupler screws. 2. A
Inhaltszusammenfassung zur Seite Nr. 18
VIVOTEK Accessories VIVOTEK also provides other accessories for versatile applications as the following illustrations. Please visit VIVOTEK's official website for more purchase information. Pole Mount Bracket Corner Mount Bracket IR illuminator (distance 30m, 60°) Built-in 24 LED units (distance 25m, 35°) The 30m, 60° IR illuminator extends the coverage of the Network Camera and reduces the halo effect around captured images. 18 - User's Manual 60° 35°
Inhaltszusammenfassung zur Seite Nr. 19
VIVOTEK Accessing the Network Camera This chapter explains how to access the Network Camera through web browsers, RTSP players, 3GPP-compatible mobile devices, and VIVOTEK recording software. Using Web Browsers Use Installation Wizard 2 (IW2) to access to the Network Cameras on the LAN. If your network environment is not a LAN, follow these steps to access the Netwotk Camera: ® 1. Launch your web browser (ex. Microsoft Internet Explorer, Mozilla Firefox, or Netscape). 2. Enter the IP addres
Inhaltszusammenfassung zur Seite Nr. 20
VIVOTEK ► By default, the Network Camera is not password-protected. To prevent unauthorized access, it is highly recommended to set a password for the Network Camera. For more information about how to enable password protection, please refer to Security on page 34. ® ► If you see a dialog box indicating that your security settings prohibit running ActiveX ® Controls, please enable the ActiveX Controls for your browser. 1. Choose Tools > Internet Options > Security > Custom Level. ® 2. Loo
