Inhaltszusammenfassung zur Seite Nr. 1
Cordless Impact Driver
MODEL 6901D
MODEL 6901DW
With Fast Charger
INSTRUCTION MANUAL
SPEC IF I CAT1 0 N S
Capacities No load Impacts Max
Dimensions Net
speed per tightening torque
(C x W x HI
weight
Machine screw and bolt IRPM) minute (Note 1)
Battery Cartridge 9100
Model DC9700 Fast Charger
Voltage 1 Charging time 1 Input I output
9.6 V 1 1 Hr. 1 A.C. only 50Hz - 60Hz 1 D.C. 7.2V. 9.6V
~~
Note 1 After tightening high tensile bolt MlOFllT for 3 seconds while using a fully charge
Inhaltszusammenfassung zur Seite Nr. 2
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools to rain. Don't use tool in presenc
Inhaltszusammenfassung zur Seite Nr. 3
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 17. STAY ALERT. Watch what you are doing, use common sense. Don't operate tool when you are t
Inhaltszusammenfassung zur Seite Nr. 4
IMPORTANT SAFETY INSTRUCTIONS 1. SAVE THESE INSTRUCTIONS - This manual 2. 3. 4. 5. 6. 7. 8. Length of Cord (Feet) 25 50 100 150 AWG Size of Cord 18 18 18 16 9. 10. 11. 12. To reduce risk of electric shock, unplug charger from outlet before attemp- ting any maintenance or cleaning. Turning off controls will not reduce this risk. 4
Inhaltszusammenfassung zur Seite Nr. 5
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) or ABOVE 4OoC (104OF). 2. Do not attempt to use a step-up transformer, an engine generator or DC power receptacle. 3. Do not allow anything to cover or clog the charger vents. 4. Do not short the battery cartridge: (1) Do not touch the terminals with any conductive material. (2) Avoid storing battery cartridge in a container with other metal objects such as n
Inhaltszusammenfassung zur Seite Nr. 6
Installing or removing battery cartridge .Always switch off the tool before insertion or removal of the battery cartridge. *To remove the battery cartridge, pull out set plate and grasp both sides of the the cartridge while withdrawing it from the tool. 0 To install the battery cartridge, insert the battery cartridge into the housing and snap the set plate back into place. Be sure to close the set plate fully before using the tool. Charging Plug the fast charger into your power sou
Inhaltszusammenfassung zur Seite Nr. 7
Installing or removing driver bit CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the bit. Slide the sleeve toward the motor and in- sert the bit into the sleeve as far as it will sleeve to secure the go. Then release the bit. To remove the bit, slide the sleeve toward the motor and pull the bit out firmly. NOTE : If the bit is not inserted deep enough into the sleeve, the sleeve will not return to its origina
Inhaltszusammenfassung zur Seite Nr. 8
Operation The proper tightening torque may differ depending upon the kind or size of the screw, the material of the workpiece to be tightened, etc. The relation between tightening torque and tightening time is shown in the figures below. Machine screw Kg . cm Ift . lbsl for M6 (1/4") + (4) Proper tightening torque for M5 (3/16") 1 I 05 1 seconds 0 Standard bolt Kg . cm (ft . Ibs) 500 - (36) M10 (3/8") M8 (5/16"1 Proper tightenlng torque for M10 (3/8") Proper tightening to
Inhaltszusammenfassung zur Seite Nr. 9
Hold the tool firmly and place the point of the driver bit in the screw head. Apply for- ward pressure to the tool to the extent that the bit will not slip off the screw and turn the tool on to start operation. NOTE : Use the proper bit for the head of the screw that you wish to use. Hold the tool pointed straight at the screw. If you tighten the screw for a time longer than shown in the figures above, the screw or the point of the driver bit may be overstressed, stripped, damaged, etc. B
Inhaltszusammenfassung zur Seite Nr. 10
MAINTENANCE CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 10
Inhaltszusammenfassung zur Seite Nr. 11
ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Bits 0 Fast charger Model DC9700 1 Size Part NO. Phillips 0 Charger 12V for car Model DC9112 0 Keyless drill chuck Part No. 192048-7 0 Battery cartridge 9100 Part No. 192019-4 0 Ste
Inhaltszusammenfassung zur Seite Nr. 12
Jan.-l8-'89 EN CORDLESS IMPACT DRIVER Model 6901D Note: The switch and other part configurations may differ from country to country. 12
Inhaltszusammenfassung zur Seite Nr. 13
MODEL 6901D Jan.-l8-'89 EN '7;'," $.& DESCRIPTION 1 1 Name Plate 15 1 Rubber Washer 20 2 1 Housing Set IWith Item 211 16 1 Sleeve 14 3 1 Switch Lever 17 1 011 Seal 14 4 1 Switch 18 1 Compression Spring 13 5 1 Switch 19 1 Sleeve 20 1 Retaining Ring S- 12 6 1 Set Plate 7 1 DC Motor 9 6 V 21 1 Housing Set IWith Item 21 22 8 Tapping Screw 4x20 8 1 Spindle 23 1 Pan Head Screw M4x20 (With Washer) 9 2 Steel Ball 5 6 10 1 COmDreSSlOn SPrV 24 24 1 Plane Bearing 4 Gear Complete 15-51 11 1
Inhaltszusammenfassung zur Seite Nr. 14
8’ r 1 MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship
