Inhaltszusammenfassung zur Seite Nr. 1
#6-3317 SINGLE BAG GRASS CATCHER for SNAPPER
REAR ENGINE RIDERS with 28/33” DECKS & LAWN TRACTORS with 33” DECKS
This grass catcher kit fits Lawn Tractors with 33” Decks and Rear Engine Riders with 28” & 33” Decks. On
Series “A” & Later Lawn Tractors, Adapter Kit #6-1334 must be installed before this grass catcher can be
installed. On Series “0-2” Lawn Tractors, Adapter Kit #6-1068 must be installed before this grass catcher can
be installed. Install adapter kit as described by instructio
Inhaltszusammenfassung zur Seite Nr. 2
NOTE: If mulching cover is installed on deck it must TUBE HANDLE be removed before going to step 5. (Also change from mulching blade to regular blade.) STEP 5: ADAPTER TO DECK MOUNTING Loosen the three hex head deflector hinge screws. Remove the side deflector bolts & wing nut and store for future use. See Figure 5A. For riders, lift the deflector. For tractors, remove palnut, hinge pin, hinge spring & deflector; save for future use. See Figure 5A. Position the TUBE HANDLE adapter o
Inhaltszusammenfassung zur Seite Nr. 3
STEP 7: DUST SKIRT TO FRAME INSTALLATION TRACTOR MODEL SHOWN (DEFLECTOR REMOVED) Punch out or tear out the center portion of the reinforcement patches (There are two large ovals and RETAINING five small round patches) on dust skirt. Insert the legs of RIDGES the frame through the two larger holes in the skirt. ENGAGEMENT Position the five patches over the studs on the frame LUGS (make sure square shield patch on skirt is installed on muffler side). See Figure 7. Then push the fram
Inhaltszusammenfassung zur Seite Nr. 4
STEP 9: Insert the bag rod (item 4, see page 6) into the STEP 11: WEIGHT PLATE INSTALLATION (REAR upper loop of the grass catcher bag (Item 5, see page 6) ENGINE RIDER ONLY) and work the grass bag until completely around the bag IMPORTANT: Some model Riders may require the two rod. The opening should be positioned at the bag rod mounting holes to be drilled in the front frame. See Step 12 opening. Push the bag rod connector (item 12, see page for drilling instructions. The mounting holes i
Inhaltszusammenfassung zur Seite Nr. 5
SINGLE BAG GRASS CATCHER KIT ILLUSTRATION INSTALL LATCH AS SHOWN FIGURE 13 5
Inhaltszusammenfassung zur Seite Nr. 6
SINGLE BAG GRASS CATCHER KIT ILLUSTRATION #6-1777 AIR LIFT KIT 28” & 33” DECK FIGURE 14 6
Inhaltszusammenfassung zur Seite Nr. 7
SINGLE BAG GRASS CATCHER KIT PARTS LIST ITEM PART NO. DESCRIPTION - 6-1413 KIT, Single Bag Grass Catcher (Includes Items 1 thru 28) 1 5-3667 TOP, Container (Includes 2-9784 &1-9910 Decals) 2 1-6108 SKIRT, Dust 3 4-7973 FRAME 4 3-7758 ROD, Bag 5 1-9251 BAG, Grass Catcher 6 5-3669 ADAPTER, Catcher (Includes 2-9784 Decal) 7 7-1677 SHIELD, Muffler 8 1-4517 TUBE, Grass - 6-0313 BAG, Hardware (Includes Items 9 thru 23) 9 3-7745 HANDLE, Tube 10 3-1952 BA
Inhaltszusammenfassung zur Seite Nr. 8
GRASS CATCHER OPERATION Your Grass Catcher equipped SNAPPER machine will keep your lawn cleaner than it would be by raking or using any other vacuum method. The Hi-Vac models, which feature a patented rolled-lip deck design, will do an excellent job of vacuuming and bagging grass clipping, leaves, litter, and even hard to pick-up pine straw. Following are some hints for using the grass catcher. • Grass clippings and litter are picked up by the vacuum created by the cutter blade and bl
