Inhaltszusammenfassung zur Seite Nr. 1
Safety Instructions & Operator’s Manual for
21” STEEL DECK
WALK MOWERS
SERIES 18
MODELS
216518B
P216518B
P217018BV
P217018BVE
P216018KWV
RP217018BV
RP217018BVE
RP216018KWV
MODEL NUMBER EXPLANATION
P 21 70 18 B V E
SELF-PROPELLED ENGINE OPTION
CUTTING WIDTH ENGINE DESIGNATION
ENGINE HORSE POWER * SERIES DESIGNATION
R – Recycling Model P – Self Propelled Model 18 - Series Designation
21 – 21” Cutting Width 60 – 6.0 HP (Engine Horse P
Inhaltszusammenfassung zur Seite Nr. 2
IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious injury or death to the operator or other persons. The owner of the machine must understand these instructions and must allow only persons who understand these instructions to operate machine. Each person operating the machine must be of sound mind
Inhaltszusammenfassung zur Seite Nr. 3
IMPORTANT SAFETY INSTRUCTIONS SAFE HANDLING OF GASOLINE OPERATION (Continued From Previous Page) (Continued From Previous Column) 3. DO NOT remove fuel cap or add fuel with the engine 11. Before cleaning, repairing or inspecting make running. Allow the engine to cool before refueling. certain engine, blade and all moving parts have 4. DO NOT refuel the machine indoors. STOPPED. Disconnect and secure spark plug wire 5. DO NOT store the machine or fuel container inside away from plug to p
Inhaltszusammenfassung zur Seite Nr. 4
IMPORTANT SAFETY INSTRUCTIONS MAINTENANCE AND STORAGE (Continued From Previous Page) 9. Mower blades are sharp and can cut. Wrap the blades or wear heavy leather gloves and use CAUTION when handling them. 10. DO NOT test for spark by grounding spark plug next to spark plug hole; spark plug could ignite gas exiting engine. 11. Have machine serviced by an authorized SNAPPER dealer at least once a year and have the dealer install any new safety devices. 12.
Inhaltszusammenfassung zur Seite Nr. 5
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS...................................................................... 2 - 4 TABLE OF CONTENTS......................................................................................................5 SECTION 1 - FAMILIARIZATION.......................................................................................6 SECTION 2 - OPERATING INSTRUCTIONS............................................................... 7-11 Pre-start Checklist.........
Inhaltszusammenfassung zur Seite Nr. 6
Section 1 - FAMILIARIZATION BLADE BRIGGS KAWASAKI CONTROL ENGINE ENGINE WHEEL DRIVE SPEED SPEED CONTROL CONTROL CONTROL GROUND SPEED CONTROL CHOKE FAST FAST ENGINE SPEED CONTROL SLOW SLOW ROPE START HANDLE FUEL FILL OIL FILL AND DIPSTICK GRASS BAG ENGINE PRIMER REAR HEIGHT ADJUSTMENT LATCH GRASS BAG ADAPTER FRONT HEIGHT ADJUSTMENT LATCHES FIGURE
Inhaltszusammenfassung zur Seite Nr. 7
Section 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LIST 2.1.6. Clean exterior surfaces of cutting deck and Make the following checks and perform the service engine of any accumulation of spilled fuel, dirt, required before each start-up. grass, oil, etc. Keep engine air intake screen and cooling fins clear at all times. 2.1.1. Check guards, deflectors, grass bag, adapter and covers to make sure all are in place and securely 2.2 STARTING & OPERATION tightened. 2.2.1. ENGINE & BLAD
Inhaltszusammenfassung zur Seite Nr. 8
Section 2 - OPERATING INSTRUCTIONS 2.2 STARTING & OPERATION 2.3 STOPPING 2.2.1. ENGINE & BLADE (Kawasaki Engine) Stop forward motion of mower by releasing the 1. Make sure fuel valve on engine is open. See wheel drive control. Stop engine and blade by Figure 2.5. releasing the blade control. 2.4 HANDLE HEIGHT ADJUSTMENT The height of the mower handle can be adjusted as follows: 1. Loosen the lower nuts on each lower handle as shown in Figure 2.7. FUEL VALVE HIGHER LOWER HA
Inhaltszusammenfassung zur Seite Nr. 9
Section 2 - OPERATING INSTRUCTIONS STEP 1a (Kawasaki only): Attach Bag Adapter Standoff 2. Set all wheels at the same cutting height. The between rope guide pulley assembly and engine recoil. highest cutting position is Notch 6. The lowest See Figure 2.10a. cutting position is Notch 1. See Figures 2.8 & 2.9. A. Remove right rear bolt from engine recoil cover. B. Remove torx screw and nut securing rope guide pulley to bracket on bag adapter. LATCH C. Lay standoff between bolt holes
Inhaltszusammenfassung zur Seite Nr. 10
Section 2 - OPERATING INSTRUCTIONS WARNING HOOK BAG HANDLE OVER LOWER DO NOT attempt any maintenance, adjustments or HANDLES service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. 2.8 INSTALLATION of GRASS BAG (Door Type Bag) Install grass bag by sliding connector over flange of adapter. See Figure 2.12.
Inhaltszusammenfassung zur Seite Nr. 11
Section 2 - OPERATING INSTRUCTIONS 2.12 INSTALLATION of RECYCLING COVER WARNING (Optional Accessory on Some Models) It will be necessary to remove bag adapter and grass bag DO NOT attempt any maintenance, adjustments or or discharge deflector before installing recycling cover. service with engine and blade running. STOP engine See previous section for instructions. Install the recycling and blade. Disconnect spark plug wire and secure cover and secure to the side and top of the deck
Inhaltszusammenfassung zur Seite Nr. 12
Section 3 – MAINTENANCE 3.1 INTRODUCTION 3.2.2. CHECK GREASE LEVEL IN TRANSMISSION To retain the quality of the mower, use genuine 1. Remove transmission fill plug. Roll machine SNAPPER replacement parts only. Contact a local forward or backward while looking down into plug SNAPPER dealer for parts and service assistance. hole. For the correct part or information for a particular 2. If liquid grease IS NOT visible on the input gear mower, always mention model and serial number. (the s
Inhaltszusammenfassung zur Seite Nr. 13
Section 3 – MAINTENANCE 3.4 STORAGE PROCEDURE WARNING Refer to the Engine Owner’s Manual for directions DO NOT attempt any maintenance, adjustments or regarding engine storage preparations. Prepare the service with engine and blade running. STOP engine mower for “end of season” storage as follows: and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are 1. Drain fuel from fuel tank and let engine run until HOT. Avoid serious burns, allow suf
Inhaltszusammenfassung zur Seite Nr. 14
Section 4 - REPAIR & ADJUSTMENTS 2. Replace the blade if it is badly chipped, bent, WARNING noticeably out of balance or has cracks or notch in DO NOT attempt any maintenance, adjustments or either tip. See Figure 4.1 & 4.1A. Replace with new service with engine and blade running. STOP engine blade. and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are WARNING HOT. Avoid serious burns, allow sufficient time for DO NOT use a cutting blade
Inhaltszusammenfassung zur Seite Nr. 15
Section 4 - REPAIR & ADJUSTMENTS CLUTCH CABLE WARNING DO NOT attempt any maintenance, adjustments or VINYL SPRING service with engine and blade running. STOP engine 1/16” TO 1/8” CLUTCH CABLE and blade. Disconnect spark plug wire and secure CLEARANCE EYE away from spark plug. Engine and components are UPPER SPRING HOT. Avoid serious burns, allow sufficient time for SPRING HOOK all components to cool. LOWER SPRING 4. Sharpen blade on a grinding wheel at an angle of 22 to 28 d
Inhaltszusammenfassung zur Seite Nr. 16
Section 4 - REPAIR & ADJUSTMENTS USE WARNING NEEDLE DO NOT attempt any maintenance, adjustments or NOSE PLIERS TO service with engine and blade running. STOP engine INSTALL and blade. Disconnect spark plug wire and secure DRIVE away from spark plug. Engine and components are SPRING HOT. Avoid serious burns, allow sufficient time for all components to cool. 4.3 DRIVEN AND DRIVE DISC SERVICE If the mower does not propel itself properly, See Figure 4.6. Check for the followin
Inhaltszusammenfassung zur Seite Nr. 17
Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any maintenance, adjustments or 1/8” MEASUREMENT TO service with engine and blade running. STOP engine OUTSIDE EDGE OF DRIVE and blade. Disconnect spark plug wire and secure DISC away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for DRIVE SLIDE DRIVEN DISC all components to cool. DISC ASSEMBLY TOWARD OUTSIDE EDGE 4.3.3. DRIVEN DISC ADJUSTMENT (Continued From Previous
Inhaltszusammenfassung zur Seite Nr. 18
Section 4 - REPAIR & ADJUSTMENTS WARNING 4.3.5. Replacing Bearing In Driven Disc Assembly DO NOT attempt any maintenance, adjustments or IMPORTANT: The bearing on these machines is staked into the thrust plate. The bearing will have to be driven service with engine and blade running. STOP engine out with a mallet and a large punch. A new bearing with and blade. Disconnect spark plug wire and secure four retaining screws will have to be purchased to away from spark plug. Engine and c
Inhaltszusammenfassung zur Seite Nr. 19
Section 4 - REPAIR & ADJUSTMENTS 4.4 BELT SERVICE WARNING On self-propelled mowers, the engine belt transmits DO NOT attempt any maintenance, adjustments or power from engine to drive disc. The drive disc powers the poly-v belt, which engages the service with engine and blade running. STOP engine transmission that powers the rear wheels. Should and blade. Disconnect spark plug wire and secure these belts become worn, they could cause slippage, away from spark plug. Engine and compone
Inhaltszusammenfassung zur Seite Nr. 20
Section 4 - REPAIR & ADJUSTMENTS PULLEY POSITION WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine DRIVE DISC and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are SLOT IN END HOT. Avoid serious burns, allow sufficient time for OF DRIVE DISC all components to cool. BOLT BUSHING 4.4.1. Engine Drive Belt Replacement (Stretch Type Belts) DECK BRACKET (Contin