Inhaltszusammenfassung zur Seite Nr. 1
Operator’s Manual
21” Mulching Mower
Model 549
Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-
covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if
any). If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required
by law (Section 444
Inhaltszusammenfassung zur Seite Nr. 2
TABLE OF CONTENTS Content Page Content Page Important Safe Operation Practices 3 Maintaining Your Lawn Mower 12 Slope Gauge 6 Servicing Your Mower 12 Assembling Your Lawn Mower 7 Troubleshooting 13 Know Your Lawn Mower 9 Illustrated Parts List 14 Operating Your Lawn Mower 10 Warranty 16 Making Adjustments 11 FINDING MODEL NUMBER This Operator’s Manual is an important part of your new lawn mower. It will help you assemble, prepare and maintain the unit for best performance. Please read and under
Inhaltszusammenfassung zur Seite Nr. 3
SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol—HEED ITS WARNING. WARNING: Engine exhaust, some of its constituents, and certain vehicle components
Inhaltszusammenfassung zur Seite Nr. 4
immediately and the blade will stop rotating within 3. Do not mow on wet grass. Unstable footing could three seconds. cause slipping. 9. Mow in daylight or good artificial light; walk, not run. 10. Stop the blade when crossing gravel drives, Children walkways or roads. Tragic accidents can occur if the operator is not alert to 11. If the equipment should start to vibrate abnormally, the presence of children. Children are often attracted to stop the engine and check immediately for the the
Inhaltszusammenfassung zur Seite Nr. 5
10. Never over fill fuel tank. Fill tank to no more than ½ 4. Mower blades are sharp and can cut. Wrap the inch below bottom of filler neck to provide space for blade or wear gloves, and use extra caution when fuel expansion. servicing them. 11. Replace gasoline cap and tighten securely. 5. Keep all nuts, bolts, and screws tight to be sure the 12. If gasoline is spilled, wipe it off the engine and equipment is in safe working condition. equipment. Move unit to another area. Wait 5 6. Never ta
Inhaltszusammenfassung zur Seite Nr. 6
FOLD ON DOTTED LINE, REPRESENTING A 15° SLOPE SIGHT AND HOLD THIS LEVEL WITH A VERTICAL TREE A POWER POLE A CORNER OF A BUILDING OR A FENCE POST 15° WARNING Do not mow on inclines with a slope in excess of 15 degrees (a rise of approximately 2-1/2 feet every 10 feet). A riding mower could overturn and cause serious injury. If operating a walk-behind mower on such a slope, it is extremely difficult to maintain your footing and you could slip, resulting in serious injury. Operate RIDING mowers u
Inhaltszusammenfassung zur Seite Nr. 7
SECTION 3: ASSEMBLING YOUR LAWN MOWER Removing Unit From Carton Lower Handle Remove staples, break glue on top flaps, or cut tape at carton end and open carton. Handle Upper Remove loose parts if included with unit (i.e., Bracket Handle operator’s manual, etc.) Cut along corners, lay the carton down flat, and remove all packing material. Roll or slide unit out of carton and check carton thoroughly for loose parts. Loose Parts in Carton Grass Bag Figure 2 Side Discharge Chute
Inhaltszusammenfassung zur Seite Nr. 8
Fasten the cable to the lower handle with the two Assembling Grass Catcher cable ties found on the lower handle. Pull the cable ties tight and trim off the excess. See Figure 5. NOTE: If the grass catcher came pre-assembled, proceed to the next section. If it came unassembled, Cable Tie follow the steps below to assemble it first, before attaching to the mower. Insert frame into grass bag with the black plastic Lower side on the bottom of bag. See Figure 8. Handle Slip the openings in
Inhaltszusammenfassung zur Seite Nr. 9
hardtop cover so that the holes in the cover line up To remove the grass catcher, lift the rear discharge with the holes in the bracket. Insert the self tapping door on the mower, lift the grass catcher up and off screws down through the hardtop cover and the pivot rod. Release the rear discharge door. mounting bracket. Attaching Side-Discharge Chute Remove the grass catcher and let the discharge Attaching Grass Catcher & Chute door close. On the right side of the mower, lift the mulc
Inhaltszusammenfassung zur Seite Nr. 10
Cutting Height Adjustment Levers Mulching Plug These levers are located on each wheel and are used Instead of collecting grass clippings in a grass catcher, to adjust the cutting height. These levers have to be at this mower has the option of recirculating the clippings the same relative position to ensure uniform cut. back to the lawn. This is called mulching. Remove the grass catcher and the side-discharge chute from the Recoil Starter mower, and operate with the mulching plug only for thi
Inhaltszusammenfassung zur Seite Nr. 11
Bagging Grass Clippings WARNING: If the mower strikes a foreign You can use the grass catcher bag to collect clippings object, stop the engine. Remove spark plug while you are operating the mower. wire from the spark plug and thoroughly inspect for any damage. Repair the damage promptly Attach grass catcher following instructions on page before restarting and operating the mower. 9 of this manual. Grass clippings will automatically collect in the bag as you run the mower. For a healt
Inhaltszusammenfassung zur Seite Nr. 12
SECTION 7: MAINTAINING YOUR LAWN MOWER Put the mower back on its wheels on the ground. If WARNING: Always stop the engine and you had put plastic under the gas cap, make sure to disconnect the spark plug wire before remove it now. performing any maintenance work or adjustments on your lawn mower. Lubrication Blade Control Handle Cleaning Mower Lubricate the pivot points on the blade control The underside of the mower deck should be cleaned handle at least once a season with light oil
Inhaltszusammenfassung zur Seite Nr. 13
Follow the original angle of grind as a guide. Make Place blade bell support on blade. Make sure the sure that each cutting edge receives an equal notches on the blade bell support are aligned with amount of grinding to prevent an unbalanced blade. small holes in the blade. Replace hex bolt and tighten hex bolt to torque: 450 WARNING: An unbalanced blade will cause in. lbs. min., 600 in. lbs. max. excessive vibration when rotating at high NOTE: To ensure safe operation of your mower,
Inhaltszusammenfassung zur Seite Nr. 14
SECTION 10: PARTS LIST FOR MODEL 549 2 1 3 36 13 12 14 6 5 7 11 8 9 10 31 49 34 16 19 22 32 21 20 64 18 24 35 45 29 33 46 15 39 28 23 25 36 26 30 29 49 4 42 40 43 37 49 60 49 52 51 17 50 54 59 61 65 53 55 40 62 57 49 47 56 58 66 14
Inhaltszusammenfassung zur Seite Nr. 15
Model 549 Ref. Ref. Part No. Part Description Part No. Part Description No. No. 1. 749-1092A Upper Handle 33. 712-3005 Flange Lock Nut 3/8-16 2. 747-1161A Control Handle 34. 710-0703 Hex Carriage Screw 1/4-20 3. 731-04302 Hardtop Cover 35. 687-02033 Handle Bracket — RH 4. 731-1506 Front End Cover 687-02031 Handle Bracket — LH 5. 787-01113 Grass Bag Mounting Bracket 36. 710-1652 Self-tapping Screw 1/4-14 x.625 6. 720-0279 Handle Knob 37. 710-0216 Hex Screw 3/8-16 x 0.75 7. 710-1205 Rope Guide 3
Inhaltszusammenfassung zur Seite Nr. 16
MANUFACTURER’S LIMITED WARRANTY FOR: The limited warranty set forth below is given by MTD LLC with e. MTD does not extend any warranty for products sold or respect to new merchandise purchased and used in the exported outside of the United States, its possessions United States, its possessions and territories. and territories, except those sold through MTD’s authorized channels of export distribution. “MTD” warrants this product against defects in material and f. Replacement parts that are n
