Inhaltszusammenfassung zur Seite Nr. 1
59757 Sub-Frame Mounting Kit
Woods Backhoe Model
mounting to
BH6500
Ford/New Holland
Tractor Models
TC18, TC21
Compatible with:
New Holland Loader
7106
or
Woods Loader
1006
MANUAL
PART NUMBER
59756
PN-59756 (Rev. 4/9/01)
Inhaltszusammenfassung zur Seite Nr. 2
TO THE DEALER: Assembly and proper installation of this product is the responsibility of the WOODS dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual are completed before releasing equipment to the owner. The dealer must complete the Warranty Registration included in this manual. Both dealer and customer must sign the registration which certifies that all Dealer Check List items have been completed
Inhaltszusammenfassung zur Seite Nr. 3
TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ii SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 PUMP KIT INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 #59757 SUB-FRAME MOUNTING KIT . . . . . . . . . . . . . . . . . . . . . .
Inhaltszusammenfassung zur Seite Nr. 4
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! a doctor familiar with this form of injury or gan- Safety is a primary concern in the design and grene, serious injury, or death will result. CON- manufacture of our products. Unfortunately, our TACT A PHYSICIAN IMMEDIATELY IF FLUID efforts to provide safe equipment can be wiped ENTERS SKIN OR EYES. DO NOT DELAY. out by an operator’s single careless act. Never allow children or untrained persons to In addition to the design and con
Inhaltszusammenfassung zur Seite Nr. 5
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! check and comply with these instructions may hoe and use extreme care Always stand between rear tire and backhoe result in serious injury or death. stabilizer arms or along side of tractor to avoid Remove seat and upper support assembly being trapped should the boom swing control before installing or removing backhoe from tractor. be accidentally activated. Failure to comply may result in equipment failure Never leave equipment
Inhaltszusammenfassung zur Seite Nr. 6
BACKHOE SUB-FRAME INSTALLATION Safety is a primary concern in the design and manufacture of our products. Unfortunately, our W ARNING efforts to provide safe equipment can be wiped out by an operator’s single careless act. Only use #59757 Sub-Frame Mounting Kit for In addition to the design and configuration of mounting Woods BH6500 backhoe on Ford/New equipment, hazard control and accident preven- Holland TC18, TC21 tractor models. Sub-Frame tion are dependent upon the awareness, concern, mu
Inhaltszusammenfassung zur Seite Nr. 7
SUB-FRAME INSTALLATION Cont’d CAUTION If you do not understand any part of this man- ual and need assistance, see your dealer. Always wear relatively tight and belted clothing to avoid entanglement in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head. * Operator’s seat must be located in the lowest and most forward position to obtain 40” minimum radius. Figure 1 Sub-Frame Clearance TRACTOR PREPARATION 3. Disconnect and rem
Inhaltszusammenfassung zur Seite Nr. 8
SUB-FRAME INSTALLATION Cont’d Install Rear Hanger Brackets 21 22 1. Install new right and left rear hanger brackets (1, 2 2), using eight 10mm bolts (20) and hardened flat washers (22). 20 1 2. Install six 10mm x 1.5P x 80mm (21) and washers 22 (22) to secure rear hangers. 3. Install cap screws (25), washers (29), and nuts 28 (28) through crossmembers welded to rear hanger 29 brackets. 4. Torque 10mm cap screws to 29 lbs-ft. 5. Torque 12mm cap screws to 50 lbs-ft. 29 25 1. 1000578 Right
Inhaltszusammenfassung zur Seite Nr. 9
SUB-FRAME INSTALLATION Cont’d Install Mid-mount Bracket GREASE FITTINGS 1. Install mid-mount bracket (3) to underside of transmission housing, using cap screws (23) and washers (29) as shown in Figure 4. NOTE: Bracket has a small notch, to be positioned on the left side the the tractor. NOTE: Leave hardware loose. 2. The mounting kit will limit access for two grease fittings on the clutch and brake pedals. Replace 6mm 23 29 straight grease fitting with a 90-degree grease fitting (not supplied
Inhaltszusammenfassung zur Seite Nr. 10
SUB-FRAME INSTALLATION Cont’d Modify Loader Mounts For tractors equipped with Woods 1006 Loader Loader mounts manufactured prior to April 2001 will NOTE: If rear mount has five slots on each side, pro- need to be modified before reinforcement brackets ceed to next section, Install Right & Left Reinforce- can be installed. Contact Woods Technical Service for ment Brackets. assistance. Install Right & Left Reinforcement Brackets 24 6 For tractors equipped with either New Holland 7106 or Woods 100
Inhaltszusammenfassung zur Seite Nr. 11
SUB-FRAME INSTALLATION Cont’d Install Crossmember 1. Attach crossmember bracket (4) to right and left reinforcement brackets, using cap screws (24) and washers (29) as shown in Figure 9. 4. 1000581 Crossmember bracket 24 24. 307301 M12–1.75P x 40mm Cap screw 29 29. 57811 1/2 Hardened flat washer, extra thick 4 Figure 9 Crossmember Bracket Installation PN-59756 (Rev. 4/9/01) Installation 9
Inhaltszusammenfassung zur Seite Nr. 12
SUB-FRAME INSTALLATION Cont’d Sub-Frame Fit-Up 1. Insert sub-frame (1) into rear mounting bracket cradle (2 & 3). 2. Secure with clevis pins (17) and safety pins (19). 3. Pivot sub-frame up and secure to front mount (6) with bent pin (7) and Klik pin (18). 4. Remove sub-frame from tractor. 5. Tighten 12mm hardware to 50 lbs.-ft. IMPORTANT DO NOT install the 3-point hitch top link on this subframe mounting kit. No top link bracket should be used on this backhoe. 6 19 18 17 7 17 19 1 1.
Inhaltszusammenfassung zur Seite Nr. 13
SUB-FRAME INSTALLATION Cont’d Attaching Sub-Frame to Backhoe 1. With sub-frame removed from tractor, attach to the backhoe using four cap screws (13), six lock washers (14), and six nuts (15). 2. Align step (12) and insert two cap screws (7) through sub-frame holes. Secure with lock washers (6) and nuts (5). 5. 7/8 NC Hex nut 6. 7/8 NC Hex lock nut 7. 7/8 NC x 2-1/2 Cap screw 12. Step 13. 3/4 NC x 2 Cap screw 14. 3/4” Lock washer 15. 3/4 NC Hex nut 15 14 5 6 12 13 7 CD4771A Figure 11 S
Inhaltszusammenfassung zur Seite Nr. 14
SUB-FRAME INSTALLATION Cont’d Mount Bracket to Pump Kit NOTE: For complete information on pump kit installa- tion, consult the Woods BH6500/7500 backhoe oper- ators manual #37541. The pump mounting bracket is designed to slip over the tractor drawbar and prevent the pump from rotat- ing. 1. Trim the bracket flush with the bottom of the trac- tor drawbar if necessary. 2. Attach pump mounting bracket #59760 (2) to pump assembly as shown in Figure 12. 3. Secure with cap screw (5) and lock nut
Inhaltszusammenfassung zur Seite Nr. 15
SUB-FRAME & BACKHOE TO TRACTOR Mount Sub-Frame & Backhoe to Tractor DANGER W ARNING W ARNING The sub-frame mount is designed to provide Remove seat and upper support assembly secure mounting and adequate operator clear- before installing or removing backhoe from trac- ance when properly installed. Check clearance tor. Failure to comply may result in equipment fail- dimensions shown in figure 1 to be sure you have ure and/or personal injury. installed sub-frame correctly. Follow all mounting
Inhaltszusammenfassung zur Seite Nr. 16
SUB-FRAME & BACKHOE TO TRACTOR Cont’d 1. Couple the backhoe hydraulic pump to the tractor Connect Hydraulic System PTO. 2. Insert the pump bracket over the tractor drawbar to prevent pump rotation. Engage the pump PTO cou- W ARNING pler pin firmly in the tractor PTO spline groove. 3. Check all hydraulic fittings and lines to be sure Keep hands and body away from pressurized they are tight and free of kinks or twists. lines. Use paper or cardboard, not hands or other 4. Make sure backhoe PT
Inhaltszusammenfassung zur Seite Nr. 17
SUB-FRAME & BACKHOE to TRACTOR Cont’d Remove Backhoe With Sub-Frame DANGER W ARNING W ARNING The only time the backhoe may be operated Remove seat and upper support assembly from a position other than the operator seat is before installing or removing backhoe from trac- during backhoe attachment and removal. Opera- tor. Failure to comply may result in equipment fail- tor must ure and/or personal injury. Read Sub-Frame Mounting Kit Manual instructions on attaching and removing back- hoe and
Inhaltszusammenfassung zur Seite Nr. 18
#59757 SUB-FRAME MOUNTING KIT 30 21 22 15 20 1 2 22 25 29 28 24 6 29 28 29 29 3 29 25 5 28 29 29 24 28 29 29 29 27 29 25 23 33 29 4 32 26 10 31 7 36 35 8 34 16 9 CD5888 Serial Number Plate Located inside sub-frame side rail, rear of cross tube MODELNO. SERIALNO. MASS (KG) ID NO. YR OF MFG. OREGON, IL U.S.A. PN-59756 (Rev. 4/9/01) 16 Parts
Inhaltszusammenfassung zur Seite Nr. 19
#59757 SUB-FRAME MOUNTING KIT PARTS LIST REF PART QTY DESCRIPTION REF PART QTY DESCRIPTION 1 1000578 1 BRACKET-REAR HANGER RT 23 62584 4 HHCS M12-1.75P X 35MM 2 1000579 1 BRACKET-REAR HANGER LT 24 307301 6 HHCS M12-1.75P X 40MM 3 1000590 1 BRACKET-MID MOUNT 25 58515 8 HHCS M12-1.75P X 45MM CL10.9ZP 4 1000581 1 BRACKET-CROSS MEMBER 26 58516 2 HHCS M12-1.75P X 50MM CL10.9ZP 5 1000594 1 BRACKET-REINFORCEMENT RT 27 307302 4 HHCS M12-1.75P X 90MM 6 1000595 1 BRACKET-REINFORCEMENT LT 28 307813 12 NUT
Inhaltszusammenfassung zur Seite Nr. 20
BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly. All torque values are given to specifications used on hardware define
