Inhaltszusammenfassung zur Seite Nr. 1
®
Hot Water Dispenser
Installation
Instructions
AND
Use and Care
Guide
IMPORTANT:
Read and save these instructions.
IMPORTANT:
Installer: Leave this guide with
homeowner.
Homeowner: Keep this guide for
future reference. Save this guide for
local electrical inspector’s use.
A Note to You Record your model’s information
Please read the Installation Instructions
Write down the following information about your hot water dispenser to better
and Use and Care Guide. It contains
help you obtain assista
Inhaltszusammenfassung zur Seite Nr. 2
Table of Contents A Note to you . . . . . . . . . . . . Cover Using Your Hot Water Troubleshooting. . . . . . . . . . . . . 12 Dispenser . . . . . . . . . . . . . . . . . 10 Hot Water Dispenser Safety . . . . 2 Requesting Assistance Before using the first time . . . . . . 10 or Service . . . . . . . . . . . . . . . . . 13 Parts and Features . . . . . . . . . . . 3 Temperature control . . . . . . . . . . 10 Warranty . . . . . . . . . . . . . . . . . . 14 How your hot water dispenser works . . .
Inhaltszusammenfassung zur Seite Nr. 3
Parts and Features How your hot water dispenser works Water is electrically heated to a enters the bottom of the tank and brewing/cooking hot 190°F by a forces hot water out of the faucet. tank that mounts under the sink. A The system is vented so the tank is thermostat maintains it at this not pressurized. approximate temperature. When you turn the On/Off Cap, cold water Use this hot water dispenser listed to help you find more detailed illustration to help you quickly learn information about t
Inhaltszusammenfassung zur Seite Nr. 4
Before You Start Check location where hot water If spout is not to be installed in sink dispenser will be installed. Proper spray hose opening, contact a installation is your responsibility. qualified installer for the best Make sure you have everything procedure for cutting a spout necessary for correct installation. It is opening in your type of sink or the responsibility of the installer to countertop. comply with installation specifications Plumbing connections must comply and with state and
Inhaltszusammenfassung zur Seite Nr. 5
Before You Start cont. Tools and materials needed Electrical requirements ruler or measuring tape 3-prong WARNING pliers ground-type wall receptacle pencil 3-prong gloves ground flat-blade plug screwdriver safety Electrical Shock Hazard glasses ground Plug into a grounded 3 prong prong outlet. tubing cutter power Do not remove ground prong. supply cord 1/4" drill bit Do not use an adapter. Recommended ground method hand or Do not use an extension cord. electric drill For your personal safety,
Inhaltszusammenfassung zur Seite Nr. 6
Installation Instructions 3. 6. Numbers 15. correspond 2. to steps. 5. 4. 5. clear tubing 8. 13. 9. 13. 12. 7. 10. 11. 14. off position 16. NOTE: Do NOT plug power supply cord into outlet. 1.Put on gloves and safety glasses. 2.Determine where you will install NOTE: It is recommended that only your hot water dispenser. Check a licensed plumber or professional below sink to assure that reinforcing installer cut an opening in the sink ribs, support brackets or cabinet or countertop. construction
Inhaltszusammenfassung zur Seite Nr. 7
Installation Instructions cont. NOTE: Do NOT plug power supply cord into outlet. 4.Lay spout assembly on flat Slide gasket over tubing so that lip surface with coiled tubing facing up. side of gasket is seated into base of Using one hand to hold tubing just spout. below spout, carefully straighten tubing with other hand. gasket 5.Loosen square nut until it is Hold nut, bracket, gasket and tubing flush with end of the mounting screw. in position and insert into hole in sink Tip spout bracket agai
Inhaltszusammenfassung zur Seite Nr. 8
Installation Instructions cont. NOTE: Do NOT plug power supply cord into outlet. 8.Connect 1/4" spout tubing NOTE: If you need to remove tubing, (longer tubing) to the rear quick- push down on collet. Pull tubing out connect fitting on top of tank. Push of quick-connect fitting. tubing straight into fitting as far as it quick- will go. Pull on tubing. The tubing connect should not come out when properly fitting installed. collet Do Not lengthen, twist or tightly bend tubing. 9.Connect clear tubi
Inhaltszusammenfassung zur Seite Nr. 9
Installation Instructions cont. 13.Connect water supply line NOTE: If you need to remove tubing, from saddle valve to spout copper push down on collet. Pull tubing out tubing with the factory-assembled of quick-connect fitting. water supply line quick-connect fitting. Push water supply line tubing straight into fitting quick-connect as far as it will go. Pull on tubing. fitting The tubing should not come out when properly installed. Turn the copper saddle valve handle counterclockwise tubing to
Inhaltszusammenfassung zur Seite Nr. 10
Using Your Hot Water Dispenser Before using the first time Check that installation Steps 14-16 were completed. The hot water dispenser can be permanently damaged if these steps are not followed. Temperature control The water temperature is best performance. However, under thermostatically controlled. It can be certain conditions, it is possible for adjusted from “Off” to approximately the water to boil when the 190°F. Temperature Control is set at “Max.” If you see any vapor or hear boiling, To
Inhaltszusammenfassung zur Seite Nr. 11
Caring For Your Hot Water Dispenser Energy-saving tips and preparation for periods of nonuse On average, you will use your hot However, if the hot water dispenser water dispenser to heat 7 to 8 cups will not be used for an extended of water per day. This uses only 19 period of time, follow these kilowatt-hours of energy per month. instructions: So it is Not necessary to turn off the hot water dispenser each night to conserve energy. For short periods (2-30 days of nonuse): Set the Temperature Co
Inhaltszusammenfassung zur Seite Nr. 12
Troubleshooting Before calling for service... If hot water dispenser does not operate, check these points first: Has circuit breaker tripped or Is the Temperature Control set Is the electrical outlet 3 3 3 house fuse blown? to the “Off” position? controlled by a switch? Is power supply cord plugged Has the water supply been 3 3 in? turned off? If you need more help, check the chart below. This could save you the cost of a service call for a problem that is not covered by the warranty. PROBLEM CH
Inhaltszusammenfassung zur Seite Nr. 13
Requesting Assistance or Service To avoid unnecessary service calls, please check the “Troubleshooting Guide” section. It may save you the cost of a service call. If you still need help, follow the instructions below. 1. If you need assistance*… Call the Whirlpool Consumer Assistance Center If you prefer, write to: telephone number. Dial toll-free from anywhere in Consumer Assistance Representative the U.S.A. 1-800-253-1301 and talk with one of our Whirlpool Corporation trained consultants or vi
Inhaltszusammenfassung zur Seite Nr. 14
® WHIRLPOOL Hot Water Dispenser Warranty LENGTH OF WHIRLPOOL WHIRLPOOL WARRANTY: WILL PAY FOR: WILL NOT PAY FOR: ONE YEAR FULL Replacement parts and repair labor costs A. Service calls to: WARRANTY to correct defects in materials or workman- 1. Correct the installation of the Hot Water FROM DATE OF ship. Service must be provided by an Dispenser. INSTALLATION authorized Whirlpool servicing outlet. 2. Instruct you how to use the Hot Water Dispenser. 3. Replace house fuses or correct house wiring
Inhaltszusammenfassung zur Seite Nr. 15
15
Inhaltszusammenfassung zur Seite Nr. 16
Part No. 3192760 ©1999 Whirlpool, U.S.A. ®Registered Trademark of Whirlpool, U.S.A. Printed in U.S.A
