Bedienungsanleitung Graco Inc. DURON 308-646

Bedienungsanleitung für das Gerät Graco Inc. DURON 308-646

Gerät: Graco Inc. DURON 308-646
Kategorie: Malpistole
Produzent: Graco Inc.
Größe: 1.22 MB
Datum des Hinzufügens: 8/19/2013
Seitenanzahl: 36
Anleitung drucken

Herunterladen

Wie kann man es nutzen?

Unser Ziel ist Ihnen einen schnellen Zugang zu Inhalten in Bedienungsanleitungen zum Gerät Graco Inc. DURON 308-646 zu garantieren. Wenn Sie eine Online-Ansicht nutzten, können Sie den Inhaltsverzeichnis schnell durchschauen und direkt zu der Seite gelangen, auf der Sie die Lösung zu Ihrem Problem mit Graco Inc. DURON 308-646 finden.

Für Ihre Bequemlichkeit

Wenn das direkte Durchschauen der Anleitung Graco Inc. DURON 308-646 auf unserer Seite für Sie unbequem ist, können sie die folgende zwei Möglichkeiten nutzen:

  • Vollbildsuche – Um bequem die Anleitung durchzusuchen (ohne sie auf den Computer herunterzuladen) können Sie den Vollbildsuchmodus nutzen. Um das Durchschauen der Anleitung Graco Inc. DURON 308-646 im Vollbildmodus zu starten, nutzen Sie die Schaltfläche Vollbild
  • Auf Computer herunterladen – Sie können die Anleitung Graco Inc. DURON 308-646 auch auf Ihren Computer herunterladen und sie in Ihren Sammlungen aufbewahren. Wenn Sie jedoch keinen Platz auf Ihrem Gerät verschwenden möchten, können Sie sie immer auf ManualsBase herunterladen.
Graco Inc. DURON 308-646 Handbuch - Online PDF
Advertisement
« Page 1 of 36 »
Advertisement
Druckversion

Viele Personen lesen lieber Dokumente nicht am Bildschirm, sondern in gedruckter Version. Eine Druckoption der Anleitung wurde ebenfalls durchdacht, und Sie können Sie nutzen, indem Sie den Link klicken, der sich oben befindet - Anleitung drucken. Sie müssen nicht die ganze Graco Inc. DURON 308-646 Anleitung drucken, sondern nur die Seiten, die Sie brauchen. Schätzen Sie das Papier.

Zusammenfassungen

Unten finden Sie Trailer des Inhalts, der sich auf den nächsten Anleitungsseiten zu Graco Inc. DURON 308-646 befindet. Wenn Sie den Seiteninhalt der nächsten Seiten schnell durchschauen möchten, können Sie sie nutzen.

Inhaltszusammenfassungen
Inhaltszusammenfassung zur Seite Nr. 1

INSTRUCTIONS–PARTS LIST 308–646
Rev. B
This manual contains important
Supercedes Rev. A
warnings and information.
READ AND RETAIN FOR REFERENCE
ELECTRIC, 120 VAC
Performance 390
Airless Paint Sprayer
2750 psi (195 bar) Maximum Working Pressure
Model 231–553, Series A
Complete sprayer with hoses, gun, RAC IV DripLess
Tip Guard and SwitchTip

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
COPYRIGHT 1996, GRACO INC.
Graco Inc. is registered to I.S. EN ISO 9001

Inhaltszusammenfassung zur Seite Nr. 2

Table of Contents Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ON/OFF Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Component Identification and Function . . . . . . . . . . . 5 Drive Housing, Connecting Rod, Crankshaft . . . . . . 28 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Pressure Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Operation . . . . . . . .

Inhaltszusammenfassung zur Seite Nr. 3

WARNING WARNING INJECTION HAZARD Spray from the gun, leaks or ruptured components can inject fluid into your body and cause ex- tremely serious injury, including the need for amputation. Fluid splashed in the eyes or on the skin can also cause serious injury.  Fluid injected into the skin is a serious injury. The injury may look like just a cut, but it is a serious injury. Get immediate medical attention.  Do not point the gun at anyone or at any part of the body.  Do not put your hand or fin

Inhaltszusammenfassung zur Seite Nr. 4

WARNING WARNING EQUIPMENT MISUSE HAZARD Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury. INSTRUCTIONS  This equipment is for professional use only.  Read all instruction manuals, tags, and labels before operating the equipment.  Use the equipment only for its intended purpose. If you are not sure, call your distributor.  Do not alter or modify this equipment.  Check equipment daily. Repair or replace worn or damaged parts immediately.  Do not

Inhaltszusammenfassung zur Seite Nr. 5

Component Function and Identification B N C A H E K  G D M L F J  Fig. 1 A Motor DC motor, 120 Vac, 15A, 1 phase B Drive Assembly Transfers power from DC motor to the displacement pump C Pressure Adjusting Knob Controls fluid outlet pressure D ON/OFF Switch Power switch that controls 120 Vac power to sprayer E Fluid Outlet Hose and spray gun is connected here F Displacement Pump Pressurizes fluid to be sprayed through spray gun G 50 ft (15 m) Main Hose 1/4 in. ID, grounded, nylon hose

Inhaltszusammenfassung zur Seite Nr. 6

Setup 2. Fill the wet–cup (102). Pry off the wet-cup seal. WARNING Fill the cup 1/3 full with Graco Throat Seal Liquid (TSL), supplied. Install the wet-cup seal. If you supply your own hoses and spray gun, be sure the hoses are electrically conductive, that the 3. Plug in the sprayer. Be sure the ON/OFF switch gun has a tip guard, and that each part is rated for (52) is OFF. Plug the cord into a grounded outlet at at least 2750 psi (195 bar) Working Pressure. This least 20 feet away from the spr

Inhaltszusammenfassung zur Seite Nr. 7

Operation How to use the gun trigger safety  Open or drain, position When engaged, the gun safety latch prevents the gun  Closed, or spray position from accidental triggering. See Fig. 3. WARNING INJECTION HAZARD If the gun still sprays when the gun trig-  ger safety is locked, repair the gun. See manual 308–235, supplied.  Gun safety latch  shown engaged 04646 Gun safety latch Fig. 4  shown disengaged How to use the pressure control. The pressure control controls the motor operation so th

Inhaltszusammenfassung zur Seite Nr. 8

Operation How to use the RAC IV tip guard. WARNING   INJECTION HAZARD To reduce the risk of serious injury, Tip handle shown in whenever you are instructed to relieve  spraying position. pressure, follow the Pressure Relief Turn handle 180,  Procedure on page 9. trigger gun to clear clog  Fig. 6 How to remove a tip clog. 1. Release the gun trigger. Lock the safety latch. Ro- The tip guard alerts you to the risk and helps prevent tate the RAC IV tip handle 180. See Fig. 6. placing an

Inhaltszusammenfassung zur Seite Nr. 9

Startup NOTE: If this is a first-time startup, flush the sprayer. WARNING See page 13. INJECTION HAZARD NOTE: Refer to Fig. 9 and the other figures referenced The system pressure must be manually in the text as you start the sprayer. relieved to prevent the system from starting or spraying accidentally. Fluid 1. Open the pressure drain valve (42). See Fig. 7. under high pressure can be injected through the skin and cause serious injury. To reduce the risk of 2. Don’t install the spray tip until

Inhaltszusammenfassung zur Seite Nr. 10

Startup b. If more coverage is needed, use a larger tip WARNING rather than increasing the pressure. FIRE AND EXPLOSION HAZARD To reduce the risk of static sparking and c. Adjust the direction of the spray pattern. See splashing when priming or flushing the Fig. 8. Engage the gun safety latch. Loosen system, hold a metal part of the gun the retaining nut (A). Position the tip guard for firmly to the side of a grounded metal pail before a horizontal or vertical pattern. Hold the tip triggering th

Inhaltszusammenfassung zur Seite Nr. 11

Startup 32  1/4 npsm(m) fluid outlet 33  Do not install any shutoff device here  Rotate clockwise to increase pressure  64  Shown in closed or spray position  Fill 1/3 full with TSL   28 74 52  102  67  Fig. 9  

Inhaltszusammenfassung zur Seite Nr. 12

Shutdown and Care WARNING WARNING INJECTION HAZARD INJECTION HAZARD See the warning section INJECTION To reduce the risk of serious injury, HAZARD on page 3 for information on whenever you are instructed to relieve the hazard of using damaged hoses. pressure, follow the Pressure Relief Procedure on page 9. Shutdown and Care Turn packing  nut clockwise to tighten 1. Check the packing nut/wet-cup daily (102). Re- lieve pressure first. Keep the wet-cup 1/3 full of TSL at all times to help prevent

Inhaltszusammenfassung zur Seite Nr. 13

Flushing 3. Pour one-half gallon (2 liters) of compatible solvent When to Flush into a grounded metal flushing pail. Put the suction 1. Before using a new sprayer: flush out the oil hose in the pail. which was left in to protect pump parts. 4. Open the pressure drain valve. See Fig. 4, page Before using water-base paint: flush with min- 7. eral spirits followed by soapy water, and then a clean water flush. 5. To save the paint still in the pump and hose, follow Step 6, except put the drain tube

Inhaltszusammenfassung zur Seite Nr. 14

Troubleshooting WARNING INJECTION HAZARD To reduce the risk of serious injury, whenever you are instructed to relieve pressure, follow the Pressure Relief Procedure on page 9. Basic Problem Solving Check everything in the troubleshooting table before disassembling the sprayer. TYPE OF PROBLEM WHAT TO CHECK WHAT TO DO If check is OK, go to next check When check is not OK, refer to this column Fluid pressure 1. Check pressure control knob setting. The pump 1. Slowly increase pressure setting to se

Inhaltszusammenfassung zur Seite Nr. 15

Basic Problem Solving TYPE OF PROBLEM WHAT TO CHECK WHAT TO DO If check is OK, go to next check When check is not OK, refer to this column Electrical (continued) 5. Check motor armature commutator for burn 5. Remove motor and have motor shop spots, gouges and extreme roughness. Re- resurface commutator if possible. See move motor cover and brush inspection plates page 26. to check. See page 20. 6. Check motor armature for shorts using arma- 6. Replace motor. See page 26. ture tester (growler) or

Inhaltszusammenfassung zur Seite Nr. 16

Intermediate Problem Solving TYPE OF PROBLEM WHAT TO CHECK WHAT TO DO If check is OK, go to next check When check is not OK, refer to this column Low output (continued) 3. Release gun trigger. Observe resting position of 3. If pump consistently comes to rest with pump rod (107). rod (107) fully extended, the piston pack- ings and/or piston valve may be worn. Service the pump. See page 22. 4. Check electrical supply with volt meter. Meter 4. Reset building circuit breaker; replace should read 105

Inhaltszusammenfassung zur Seite Nr. 17

Intermediate Problem Solving TYPE OF PROBLEM WHAT TO CHECK WHAT TO DO If check is OK, go to next check When check is not OK, refer to this column 1. Spray tip worn beyond sprayer pressure capa- 1. Replace spray tip. Spray Pattern Variations bility. NOTE: A smaller size tip will provide longer life. 2. Check transducer (29) for wear or damage. 2. Replace transducer. See page 31. 3. Check pressure control (64) for smooth opera- 3. Replace pressure control. See page 30. tion. 4. Check Low output se

Inhaltszusammenfassung zur Seite Nr. 18

Motor Test WARNING INJECTION HAZARD To reduce the risk of serious injury, whenever you are instructed to relieve pressure, follow the Pressure Relief Procedure on page 9. B For checking armature, motor winding and brush elec- trical continuity. Setup A Remove the drive housing. See page 28. This is to ensure that any resistance you notice in the armature test is due to the motor and not to worn gears in the drive housing. Remove the motor brush inspection covers (A). See Fig. 12.  Fig. 12 R

Inhaltszusammenfassung zur Seite Nr. 19

General Repair Information WARNING WARNING INJECTION HAZARD HOT SURFACE HAZARD During operation, the motor and drive To reduce the risk of serious injury, housing become very hot and could burn whenever you are instructed to relieve your skin if touched. Flammable materi- pressure, follow the Pressure Relief als spilled on the hot, bare motor could cause a fire Procedure on page 9. or explosion Tool List CAUTION These are the tools required to service all parts of the To reduce the risk of a pr

Inhaltszusammenfassung zur Seite Nr. 20

Motor Brushes NOTE: Replace brushes when worn to about 0.5 in.  Motor lead; do not disconnect (12.5 mm). Always check both brushes. Brush Repair  Minimum 0.5” (12.5 mm) Kit 236–967, which includes spring clip 112–766, is  Included in Brush Repair available for motors manufactured by Pacific Scientific. Kit 236–967  NOTE: Replacement brushes may last only half as  C H long as the original ones. To maximize brush life, break G in new brushes by operating the sprayer for at least  F one hour


Ähnliche Anleitungen
# Bedienungsanleitung Kategorie Herunterladen
1 Graco Inc. 1095 Premium Hi-Boy Handbuch Malpistole 11
2 Graco Inc. 12004 Handbuch Malpistole 1
3 Graco Inc. 111418a Handbuch Malpistole 1
4 Graco Inc. 12004X Handbuch Malpistole 2
5 Graco Inc. 12006 Handbuch Malpistole 2
6 Graco Inc. 12005 Handbuch Malpistole 0
7 Graco Inc. 1095 Premium Hi Handbuch Malpistole 1
8 Graco Inc. 1595 HI Handbuch Malpistole 3
9 Graco Inc. 207-945 Handbuch Malpistole 7
10 Graco Inc. 1595 Premium Hi Handbuch Malpistole 2
11 Graco Inc. 208-748 Handbuch Malpistole 0
12 Graco Inc. 208-749 Handbuch Malpistole 1
13 Graco Inc. 1595 Premium Hi-Boy Handbuch Malpistole 6
14 Graco Inc. 208-644 Handbuch Malpistole 1
15 Graco Inc. 218-026 Handbuch Malpistole 2
16 3M Series 52 Handbuch Malpistole 1
17 3M Series 56 Handbuch Malpistole 0
18 3M Series 56ZZ Handbuch Malpistole 1
19 3M Series 55ZZ Handbuch Malpistole 1
20 3M Series 57 Handbuch Malpistole 1