Inhaltszusammenfassung zur Seite Nr. 1
SUNLINE 2000
SINGLE PACKAGE HEAT PUMPS
INSTALLATION INSTRUCTION 035-12984-001-A-0204
Supersedes: 511.13-N1YI (900)/035-12984-000
MODELS B3CH 048 AND 060
(WORLD 50 HZ)
GENERAL
YORK Model BCH units are single package heat pumps
• 530.18-N7.1V -Electric Heater Accessory
designed for outdoor installation on a rooftop or a slab.
• 530.18-N7.2V -Fuse Block Accessory
Supplemental electric heaters are available as field-installed
accessories. The units are manufactured under ISO 9002
Renewal Parts:
Inhaltszusammenfassung zur Seite Nr. 2
035-12984-001-A-0204 TABLE OF CONTENTS General................................................................................1 MAINTENANCE Inspection ............................................................................1 Normal Maintenance .........................................................14 Reference............................................................................1 Approvals ............................................................................1 TABLES Nomenclatu
Inhaltszusammenfassung zur Seite Nr. 3
035-12984-001-A-0204 INSTALLATION RIGGING AND HANDLING Exercise care when moving the unit. Do not remove any LIMITATIONS packaging until the unit is near the place of installation. Rig the These units must be installed in accordance with national and unit by attaching chain or cable slings to the lifting holes local or municiple safety codes: Refer to Table 1 for Unit provided in the base rails. Spreaders, whose length exceeds Application Data. the largest dimension across the unit, MUST be used
Inhaltszusammenfassung zur Seite Nr. 4
035-12984-001-A-0204 size and type. Dirty filters reduce the capacity of the unit and After this unit is installed, back out the compressor bolts until result in frosted coils or safety shutdown. Minimum filter area the sleeve clears the top grommet. and required sizes are shown in Table 3. CAUTION: Do Not loosen compressor mounting bolts. CONDENSATE DRAIN THERMOSTAT Plumbing must conform to local codes. Use a sealing compound on male pipe threads. Install a condensate drain The room thermostat
Inhaltszusammenfassung zur Seite Nr. 5
035-12984-001-A-0204 TABLE 2 - AIR FLOW LIMITATIONS NOMINAL UNIT MODEL SIZE, NOMINAL TONS HEATER 45 VOLTAGE SIZE MINIMUM SUPPLY AIR CFM KW 7 1,300 1,600 10 1,300 1,600 15 380/415-3+N-50 1,300 1,600 20 1,300 1,600 30 – 1,600 CONTROL WIRING 1 Typical 24-volt thermostat with subbase -2ET03700424 for manual changeover. 2 Only required on units with supplemental electric heat. TO REMOTE SENSOR 2ET04701324 IF USED 1 Typical Electronic programmable thermostat 2ET04701124 with subbase for either manual
Inhaltszusammenfassung zur Seite Nr. 6
035-12984-001-A-0204 heater accessory installation instruction for the heater electrical data. flange surface on each side plate. Extend gasketing 6mm ( 1 in.) beyond top and bottom of each flange to insure ade- The minimum air flow limitations across these heaters are 4 quate corner sealing. Secure this assembly to the unit back listed in Table 2. panel (upper right hand corner). First, remove screw (C) on OPTIONAL ECONOMIZER RAIN HOOD unit top cover. Then slip flange of hood cover in under fla
Inhaltszusammenfassung zur Seite Nr. 7
035-12984-001-A-0204 FIG. 5 - ENTHALPY SET POINT ADJUSTMENT TABLE 3 - PHYSICAL DATA BCH WEIGHTS (kg/lbs) MODELS 048 060 048 270 / 595 CENTRIFUGAL BLOWER (Dia. x 305 x254 305 x 254 Basic Unit SUPPLY AIR Wd.,mm/in.) 12 x 10 12 x 10 060 281 / 620 BLOWER FAN MOTOR HP (Direct-Drive Units) 0.75 NA OPTIONS / ACCESSORIES FAN MOTOR HP (Belt-Drive Units) NA 1.5 ROWS DEEP 3 3 5 - 7 kW 8.2 / 18 INDOOR FINS PER 25mm (1 inch) 15 15 Electric Heat COIL 2 2 10 - 15 kW 10.4 / 23 FACE AREA (m /ft ) 0.47 / 5.1 0.47
Inhaltszusammenfassung zur Seite Nr. 8
035-12984-001-A-0204 OUTDOOR COIL (Direct-Drive Units) 829 32-5/8" 2090 82-1/4" RETURN AIR 64 1140 2-1/2 SUPPLY AIR 44-7/8" OUTDOOR AIR 292 11-1/2" OUTDOOR AIR (Economizer) 445 17-1/2" All dimensions are in millimeters and 137 inches. They are subject to change without 5-3/8 165 6-1/2" notice. Certified dimensions will be pro- 445 17-1/2" vided upon request. 171 200 6-3/4" 7-7/8" 206 8-1/8" 213 8-3/8" UTILITIES ENTRY DATA KNOCKOUT HOLE SIZE USED FOR (DIA.) Control Wiring A 5mm (7/8") * (Side or
Inhaltszusammenfassung zur Seite Nr. 9
035-12984-001-A-0204 DUCT COVERS - Units are shipped with all air duct openings covered. For side duct applications; 1.Remove and discard the supply and return air duct covers. 2.Connect ductwork to duct flanges on the rear of the unit. 292 For bottom duct applications; 1 “ 2 1. Remove the side supply air duct cover to gain ac- cess to the bottom supply air knockout panel. 76 3" 2. Remove and discard the bottom knockout panel. 3. Replace the side duct cover. 437 1 292 4. With filter section acce
Inhaltszusammenfassung zur Seite Nr. 10
035-12984-001-A-0204 TABLE 4 - SUPPLY AIR PERFORMANCE - BCH048 380 / 415 VOLTS - SIDE DUCT APPLICATIONS Available External Static Pressure - Pa* MOTOR MODEL SPEED 3 3 3 3 3 3 3 3 3 m /s Watts m /s Watts m /s Watts m /s Watts m /s Watts m /s Watts m /s Watts m /s Watts m /s Watts HI - - - - 0.94 1010 0.92 975 0.90 945 0.87 910 0.83 825 0.78 825 0.72 775 048 MED 0.85 910 0.84 880 0.82 850 0.80 825 0.79 800 0.76 775 0.74 740 0.70 700 0.66 660 LOW 0.77 810 0.76 780 0.75 760 0.73 740 0.73 730 0.71 71
Inhaltszusammenfassung zur Seite Nr. 11
035-12984-001-A-0204 TABLE 8 - ELECTRICAL DATA - Basic Unit VOLTAGE SUPPLY MAX. MAX. MIN. COMPRESSOR OUTDOOR TOTAL LIMITATIONS AIR FUSE HACR WIRE MODEL FAN UNIT POWER SUPPLY BLOWER SIZE, BREAKER SIZE, BCH MOTOR, AMPACITY, MOTOR, (SEE NOTE 1) SIZE, AWG MIN. MAX. RLA LRA FLA AMPS FLA AMPS AMPS (SEE NOTE 2) 2 048 380/415-3+N-50 342 457 9.6 66 1.8 4.0 18.3 25 25 10 (6MM ) 2 060 380/415-3+N-50 342 457 10.0 75 1.8 2.6 16.9 25 25 10 (6MM ) NOTES: 1. Dual element, time delay type. 2. Based on 75°C copp
Inhaltszusammenfassung zur Seite Nr. 12
035-12984-001-A-0204 OPERATION screw fully clockwise and then energize and de-energize 250 terminals “R” to “G”. With terminals “R” to “G” energized, turn the minimum position screw counterclockwise until the desired minimum position has been attained. 200 T3 - 110 Minute Setting (Factory Set Point) 11. Replace the filter section access panel. 150 COOLING SYSTEM T2 - 80 Minute Setting The unit has an air-cooled condenser and is factory-charged 100 with Refrigerant-22. The compressor is hermetica
Inhaltszusammenfassung zur Seite Nr. 13
035-12984-001-A-0204 During troubleshooting, the defrost time can be reduced to 20 seconds by shorting out the SW1 test pegs on the module. The 1 3 pegs are 13mm ( in.) long, 1mm ( in.) apart and are 2 mounted on a white base. See Figure 8. LOCKOUT CONTROL Any one of four conditions will put the system into a lock-out condition during the heating or cooling mode: 1. The discharge line temperature reaches 124°C (255°F) (102°C [215°F] reset) or, 2. The discharge pressure reaches 2770 kPa (398 PSIG
Inhaltszusammenfassung zur Seite Nr. 14
035-12984-001-A-0204 3. Using an inclined manometer, determine the pressure drop across a dry indoor coil. Since the moisture on an indoor coil may vary greatly, measuring the pressure drop across a wet coil under field conditions would be inaccurate. To ensure a dry coil, the compressors should be de-energized while the test is being run. 4. Knowing the pressure drop across a dry coil, the actual airflow through the unit can be determined from the curve in Figure 11. WARNING:Failure to properly
Inhaltszusammenfassung zur Seite Nr. 15
035-12984-001-A-0204 Unitary Products Group 15
Inhaltszusammenfassung zur Seite Nr. 16
Unitary Products Group 5005 York Drive, Norman, Ok 73069 Subject to change without notice. Printed in U.S.A. Supersedes: 511.13-N1YI (900) / 035-12984-000 035-12984-001-A-0204 Copyright by York International Corporation 2004. All Rights Reserved.
