Resumen del contenido incluido en la página 1
Operator ’s Manual
R48 Recycling Mower
G008079
Code 446F , 447F
Serial No. 310000001 and Up
Manual Part No. 1 1 1-3375 Rev A
Resumen del contenido incluido en la página 2
T his product complies with all relev ant European infor mation and Note emphasizes g eneral infor mation directi v es , for details please see the se parate product w or th y of special attention. specific Declaration of Confor mity (DOC) sheet. Contents Introduction Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 T hank y ou for purc hasing a Ha yter mo w er . T he Safety . . . . . . . . . . . . .
Resumen del contenido incluido en la página 3
• If petrol is spilled, do not attempt to star t the engine Safety but mo v e the mo w er a w a y from the area of spillag e and a v oid creating any source of ignition until petrol Impr oper l y using or maintaining this mo w er can v apors ha v e dissipated. r esult in injur y . T o r educe the potential f or injur y , compl y with these safety instr uctions. • R e place all fuel tank and container caps securely . T his mo w er w as designed and tested for reasonably safe Preparation ser vice;
Resumen del contenido incluido en la página 4
– Do not mo w ex cessi v ely stee p slopes . • T o reduce the fire hazard, k ee p the engine , silencer , batter y compar tment and petrol storag e area free of – Ex ercise extreme caution when on slopes . g rass , lea v es , or ex cessi v e g rease . – Mo w across the face of slopes , nev er up and • Chec k g rass bag components and the disc harg e do wn and ex ercise extreme caution when guard frequently and re place with man ufacturer’ s c hanging direction on slopes . recommended par ts , wh
Resumen del contenido incluido en la página 5
Safety and Instructional Decals Important: Safety and instr uction decals ar e located near ar eas of potential danger . R eplace dama ged decals. Manufacturer ’ s Mark 1. Indicates the blade is identified as a part from the original machine manufacturer . 1 10-7126 1. W arning—read the 4. Cutting, dismemberment Operator ’ s Manual. hazard of hand or foot—stay away from moving parts. 5. Thrown object 2. Cutting, dismemberment hazard of hand or hazard—keep deflector in foot—remove the place. spar
Resumen del contenido incluido en la página 6
Setup Unfolding the Handle 1. Unloc k the handle loc ks , mo v e the handle sections into the operating position, and loc k the handle loc ks ( Figure 3 ). Figure 5 Filling the Engine with Oil Y our mo w er does not come with oil in the engine . Figure 3 1. R emo v e the dipstic k (Figure 6 ). 2. Unloc k the upper handle loc ks and rotate the upper handle upw ard and loc k it into a position that is comfor table to y ou ( Figure 4 ). Figure 4 Figure 6 1. Highest position 3. Lowest position 2. Mi
Resumen del contenido incluido en la página 7
Installing the Fuse (Model Charging the Battery (Model 447F Only) 447F Only) Y our mo w er comes with a 40-amp fuse that protects the R efer to Charging the Batter y in the Maintenance electric star ter . section. Important: Y ou cannot star t the mo w er with the electric star ter or charge the batter y unless y ou install the fuse. 1. R emo v e the batter y co v er and the batter y and locate the fuse holder ( Figure 7 ). Figure 7 1. Screw 3. Fuse holder 2. Battery cover 4. Battery 2. Inser t
Resumen del contenido incluido en la página 8
Product Overview Operation 5 Filling the Fuel T ank 6 7 8 P etr ol is extr emel y flamma ble and explosi v e. A 9 10 fir e or explosion fr om petr ol can bur n y ou and 4 other s. 11 3 • T o pr ev ent a static charge fr om igniting the petr ol, place the container and/or mo w er 2 dir ectl y on the g r ound bef or e filling , not in a v ehicle or on an object. 1 • Fill the tank outdoor s when the engine is 12 cold. W ipe up spills. 14 G01201 1 13 • Do not handle petr ol when smoking or Figure 9
Resumen del contenido incluido en la página 9
deterg ent oil with an API ser vice classification of Starting the Engine SF , SG , SH, SJ , SL, or higher .) 1. Hold the blade control bar ag ainst the handle 3. Install the dipstic k. (Figure 12 ). Adjusting the Cutting Height Adjusting the cutting height may bring y ou into contact with the mo ving blade, causing serious Figure 12 injur y . • Stop the engine and w ait f or all mo ving par ts to stop . 2. Pull the recoil star ter ( Figure 13 ) or tur n the ignition k ey as sho wn in Figure 14
Resumen del contenido incluido en la página 10
sides , and the mo w er will automatically k ee p pace with y ou. Figure 17 1. Recycling mode 2. Bagging mode Figure 15 Bagging the Clippings Stopping the Engine Use the g rass bag when y ou w ant to collect g rass and 1. R elease the blade control bar ( Figure 16 ). leaf clippings from the la wn. A w or n g rass ba g could allo w small stones and other similar de bris to be thr o wn in the operator’ s or bystander’ s dir ection and r esult in serious per sonal injur y or death to the operator o
Resumen del contenido incluido en la página 11
T he blade is shar p; contacting the blade can r esult in serious per sonal injur y . Stop the engine and w ait f or all mo ving par ts to stop bef or e lea ving the operating position. Operating T ips General Mowing T ips • Clear the area of stic ks , stones , wire , branc hes , and other debris that the blade could hit. • A v oid striking solid objects with the blade . Nev er deliberately mo w o v er any object. • If the mo w er strik es an object or star ts to vibrate , immediately stop the e
Resumen del contenido incluido en la página 12
– Raise the cutting height on y our mo w er . – Cut the g rass more frequently . – Ov erlap cutting sw aths instead of cutting a full sw ath with eac h pass . – Set the cutting height on the front wheels one notc h lo w er than the rear wheels . F or example , set the front wheels at 60 mm and the rear wheels at 70 mm. Cutting Leaves • After cutting the la wn, ensure that half of the la wn sho ws through the cut leaf co v er . Y ou ma y need to mak e more than one pass o v er the lea v es . • If
Resumen del contenido incluido en la página 13
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure Interval After the first 5 hours • Change the engine oil. • Check the engine oil level. • Ensure that the engine stops within 3 seconds after releasing the blade control bar . Before each use or daily • Clean the mower . • Charge the battery for 24 hours. (Model 447F only) Every 25 hours • Replace the blade or have it sharpened (more frequently if the edge dulls quickly). • Change the engine oil. Every 50 h
Resumen del contenido incluido en la página 14
Lubrication Engine Maintenance Lubricating the Wheel Gears Replacing the Air Filter Ser vice Inter v al : Y early —Lubricate the wheel g ears . Ser vice Inter v al : Y early —R e place the air filter (more frequently in dusty operating 1. R emo v e the wheel bolts on the r ear wheels and conditions). remo v e the rear wheels . 1. P erfor m the pre-maintenance procedures; refer to 2. Apply a lubricating oil to the g ear as sho wn in Pre paring for Maintenance . Figure 21 . 2. Open the air filter
Resumen del contenido incluido en la página 15
Electrical System Maintenance Charging the Battery (Model 447F Only) Ser vice Inter v al : Ev er y 25 hours —Charg e the batter y for 24 hours . (Model 447F only) Alw a ys use the c harg er in a sheltered area and c harg e the Figure 23 batter y at room temperature (22° C) whenev er possible . 1. Connect the c harg er to the mo w er wire har ness 4. Slo wl y pour oil into the oil fill tube until the oil located belo w the ignition k ey (Figure 24 ). lev el reac hes the Full line on the dipstic k
Resumen del contenido incluido en la página 16
Drive System Maintenance Adjusting the Self-propel Drive If y our mo w er does not self-propel properly , adjust the self-propel dri v e cable . 1. Loosen the n ut on the cable mount ( Figure 25 ). Figure 27 1. Exposed cable 4. Push the cable jac k et upw ard 3/16 inc h (5 mm) (Figure 28 ). Figure 28 1. Cable mount 2. Cable jacket Figure 25 Note: Y ou can place a r uler ag ainst the upper side 1. Nut on cable mount of the cable mount and measure ho w far the upper end of the cable jac k et mo v
Resumen del contenido incluido en la página 17
Important: A bolt torqued to 82 N-m is v er y Blade Maintenance tight. W hile holding the blade with a block of w ood, put y our w eight behind the ratchet or wr ench and tighten the bolt secur el y . T his bolt Replacing the Blade is v er y dif ficult to o v er tighten. Ser vice Inter v al : Ev er y 25 hours —R e place the blade or ha v e it shar pened (more frequently if the edg e dulls quic kly). Important: Y ou will need a torque wr ench to install the blade pr oper l y . If y ou do not ha v
Resumen del contenido incluido en la página 18
Cleaning Storage Store the mo w er in a cool, clean, dr y place . Cleaning the Mower Ser vice Inter v al : Before eac h use or daily —Clean the Preparing the Mower for mo w er . Storage Tipping the mo w er may cause the fuel to leak P etr ol v apor s can explode. fr om the carbur etor or the fuel tank. P etr ol is extr emel y flamma ble, highl y explosi v e, and • Do not stor e petr ol mor e than 30 days. under cer tain condition can cause per sonal • Do not stor e the mo w er in an enclosur e n
Resumen del contenido incluido en la página 19
Notes: 19
Resumen del contenido incluido en la página 20
Notes: 20
