Résumé du contenu de la page N° 1
Promaster 310 Grass Catcher
Owner/Operator & Parts Manual
Model
890015*
*NOTE: Installation requires a separate mower boot kit,
p/n 04916000 for 60" decks, p/n 04916100 for 50" decks.
08493200A 12/03
Supercedes 08493200
Printed in USA
Résumé du contenu de la page N° 2
TABLE OF CONTENTS Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Mai
Résumé du contenu de la page N° 3
SAFETY SAFETY ALERTS SAFETY DECALS AND LOCATIONS Look for these symbols to point out ALWAYS replace missing or damaged Safety Decals. important safety precautions. They mean: Refer to Parts List for Safety Decal locations. Attention! Danger! - To Avoid Serious Injury Personal Safety Is Involved! ROTATING FAN! Stop grass pump and Become Alert! power unit engines before removing any part of bagger. Wait for all moving parts to Obey The Message! stop. OL0900 The saf
Résumé du contenu de la page N° 4
Dust, fog, etc. can reduce vision and cause an Warning - Engine accident. Operate unit only when there is good visibility and light. DO NOT operate in poorly ventilated area. DO NOT refuel while engine is running. Personal Safety Make sure no flame/spark around during Only trained adults may operate unit. refuel. Training includes actual operation. DO NOT touch exhaust system and NEVER operate unit after or during the use of engine while hot. medication, drugs or alcohol. Saf
Résumé du contenu de la page N° 5
DO NOT try to stabilize the machine by putting your Keep all hardware properly tightened. foot on the ground. Cleaning Know the weight of loads. Limit loads to those you can Keep unit free of debris. Clean up oil or fuel spills. safely control and the unit can safely handle. ALWAYS keep protective structures, guards and panels STORAGE SAFETY RULES in good repair, in place and securely fastened. DO NOT store grass can with grass in them. DO NOT operate in reverse unless ab
Résumé du contenu de la page N° 6
ASSEMBLY 5. Fasten catcher tube to the tube bracket. Use the WARNING: AVOID INJURY. Read and two holes nearest the tube end. understand Assembly Safety Rules in Safety 6. Fasten ring weldment (item #35) to the pivot section before attempting to assemble unit. bracket weldment. With the ring in the raised position, place the grass can on the catcher Unpacking Unit weldment (item #50). Lower the ring onto the IMPORTANT: Remove contents from carton careful
Résumé du contenu de la page N° 7
3. Remove mower boot from deck. REMOVING BAGGER 4. Replace original discharge chute deflector. 1. Disconnect hose from blower inlet and mower boot. 2. Remove klik pins from catcher weldment and remove catcher from unit. OPERATION BAGGING WARNING: AVOID INJURY. Read and understand Operational Safety Rules in Starting Safety section before operating. IMPORTANT: ALWAYS start grass catcher engine before starting unit engine. Throttle Lever 1. Start grass cat
Résumé du contenu de la page N° 8
Stop grass catcher engine, wait for all moving UNCLOGGING GRASS CATCHER parts to stop and disconnect spark plug wire. WARNING: MOVING PARTS can cut or 2. Loosen hose clamp on hose. amputate body parts. 3. Remove hose from grass blower. NEVER attempt to clear grass pump while If clog is in hose: engine is running. 1. Remove clogged grass. ALWAYS stop unit and grass catcher engines, remove key, and wait for moving parts to stop. 2. Reinstall hose and tighten hose clamp. Sharp e
Résumé du contenu de la page N° 9
5. Adjust tension. INSPECT CATCHER PARTS 6. Replace belt guard. Before each use, inspect grass catcher parts for any holes, abrasions, or structural damage. Replace any To adjust tension: worn or damaged parts. 1. Remove belt guard. 2. Loosen hardware securing bagger engine to CLEAN UNIT weldment. Clear away grass build up in catcher before and after 3. Loosen four bolts and lock nuts holding blower to each use. catcher weldment. CHECK ENGINE OIL 4. Loosen 3/8" jam nut. Check engine oil bef
Résumé du contenu de la page N° 10
CATCHER ASSEMBLY Model 890015 PF2100 GB-10
Résumé du contenu de la page N° 11
CATCHER ASSEMBLY Model 890015 Item Part No. Qty. Description 33 08981100 1 Bushing .385 x .625 x 1.00 34 08944600 1 Weldment-Pivot Bracket 1 03444800 2 Clamp 35 08944300 1 Weldment-Ring 2 05946900 2 Bolt-Hex .31-18 x 1.00 Grade 5 36 07528100 1 Strap-Hold Down 3 06437200 10 Washer-Flat .344 x .688 x .065 37 08707400 1 Can-Grass 4 06529800 6 Nut-Locking-Center .31-18 38 05421600 1 Race-Bearing-Thrust 5 09032500 1 Tube-Catcher 39 06712600 1 Pin-Center .12 x 1.25 6 08941700 1 Cover-Guard 40 05422400
Résumé du contenu de la page N° 12
BLOWER ASSEMBLY Model 890015 PF2100 Item Part No. Qty. Description 1 03422100 1 Weldment-Spindle 2 06418500 2 Washer-Flat-Steel 1.015 x 1.5 x .125 3 21082200 1 Spacer 4 05416000 2 Bearing-Ball 1.0 x 2.0 x .56 5 04914851 1 Weldment, Fan Housing 6 05234600 1 Decal-Danger 7 03021500 1 Blade-Fan 8 06529800 4 Nut-Locking-Center .31-18 9 06512000 1 Nut-Locking-Jam 1.0-14 10 05947000 4 Bolt-Hex .31-18 x .75 Grade 5 11 03422000 1 Blade-Fan GB-12
Résumé du contenu de la page N° 13
WARRANTY 2-Year Limited Warranty Gravely Division of Ariens Company (Gravely) hereby warrants to the original consumer purchaser that all Gravely Two-Wheel, Gravely Division of Ariens Company Professional G, Pro, and ProMaster products will be free from defects 655 West Ryan Street in material and workmanship for a period of two (2) years from the date P.O. Box 157 of purchase or 1000 hours, whichever comes first. Brillion, WI 54110-0157 Protection Plan 920-756-2141 Fax 920-756-2407 Gravely will
Résumé du contenu de la page N° 14
GRAVELY A Division of Ariens Company 655 West Ryan Street P.O. Box 157 Brillion, WI 54110-0157 920-756-2141 Fax 920-756-2407 www.gravely.com
