ページ1に含まれる内容の要旨
PNEUMATIC DUST COLLECTOR PNEUMATIC DUST COLLECTOR PNEUMATIC DUST COLLECTOR PNEUMATIC DUST COLLECTOR PNEUMATIC DUST COLLECTOR
2448
ASSEMBLY AND OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
®
Copyright © 2003 by Harbor Freight Tools . All rights reserved. No portion of this manual or any
artwork contained herein may be reproduced in any shape or form without the express written consent
®
of Harbor Freight Tools .
For tec
ページ2に含まれる内容の要旨
Specifications ITEM DESCRIPTION Max. Working Pressure 125 PSI Overall Dimensions 21-1/2” Triangulation at Wheels x 30-3/4”H Castor Dimensions Qty 3, Swivel Housing w/2” Dia. x 7/8” Wheels Tank Dimensions 2-7/8” Dia. to 11-1/2” Dia. x 20-1/2”H x 3/16” Thick at top Filter Paper, 30 Micron capacity, one year lifespan if cleaned with blow gun after each use Compatibility Can be used with any 10-60 Gallon Abrasive Blast Cabinets with a 1-1/4” Dia. Outlet Net Weight 18.8 Lbs. Save This Manual You will
ページ3に含まれる内容の要旨
8. Disconnect power. Unplug product when not in use. 9. Avoid unintentional starting. Be sure the switch is in the Off position when not in use and before plugging in. 10. Stay alert. Watch what you are doing, use common sense. Do not operate any product when you are tired. 11. Check for damaged parts. Before using any product, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment and binding
ページ4に含まれる内容の要旨
3. Do not vacuum toxic, carcinogenic, combustible or other hazardous materials. There are specialized products that are specifically designed to pick up these types of materials. 4. Do not use this product without a filter installed. 5. Disconnect this product from its power source before changing the filter or adjusting the hose. 6. It is recommended that you empty the Tank after each use, or when it is 3/4 full of materials. Warning: The warnings, cautions, and instructions discussed in this i
ページ5に含まれる内容の要旨
7. Fit Suction Hose [1] over the Vacuum Body with Air Switch Assembly [10]. 8. To connect the Hose to an Abrasive Blast Cabinet (not included), unscrew the Connecting Nut [2-2] and remove the O-Ring [2-1]. Fit the Connecting Hose [2] into the 1-1/4” Dia. outlet in the Blast Cabinet. Reaffix the O-Ring and the Connecting Nut to the Hose from the inside of the Blast Cabinet. Be sure the Hose is tightly connected before use. Air Connection DUST COLLECTOR Note: Air Compressor is not supplied. 1. You
ページ6に含まれる内容の要旨
4. Disconnect the product from the Air Compressor when not in use and store in a dry location, away from children. Cleaning and Replacing the Filter 1. Disconnect Dust Collector from power source. 2. Loosen the Cover Nut and remove the Screen Cover as shown on the Assembly Diagram on page 7. Lift the Filter from the Screen and clean with a blow gun. The Filter will last approximately one year if cleaned properly with a blow gun after each use. 3. Replace the Filter, Screen Cover and Cover Nut.
ページ7に含まれる内容の要旨
Parts List and Assembly Diagram ITEM DESCRIPTION QTY 1 Suction Hose 1 2 Connecting Hose 1 2-1 O-Ring 1 2-2 Connecting Nut 1 3 Castor 3 4 1/4” Nut 6 5 1/4” x 3/4” Screw 3 6 1/4” x 5/8” Screw 6 7 1/2” Valve 1 8 Leg 3 9 Connecting Plate 3 10 Vacuum Body with Air Switch Assembly 1 11 Tank 1 12 Tank Cover 1 13 Filter 1 14 Screen 1 15 Screen Cover 1 16 Cover Nut 1 17 Sand Buffering Device 1 NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as repla
