ページ1に含まれる内容の要旨
Dust Collector
MODEL 410
INSTRUCTION MANUAL
SPEC IF I CAT I 0 N S
No load
Peak air flow when
Dimensions 1 Net
hose and dust bag 1 Sealed suction 1 1
weight
IL Hj
are installed
8.7 mJ/min. 510 mm (20") ,o,ooo 287 mm x 285 mm x 280 mm 9.3 kg
1307 cu. ft./min.) of water (1 1-114'' x 11.114" x 11") 120.4 Ibs)
~
* Manufacturer reserves the right to change specifications without notice
* Note: Specifications may differ from country to country.
;;;;dl
ページ2に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS Wh n sing an electrical appliance, basic precaution sha rld always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE WARNING -TO reduce the risk of fire, electric shock, or injury: 1. Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing. 2. Electric shock could occur if used on wet surfaces. Do not expose to rain. Store indoors. 3. Do not allow to be used as a toy. Close at
ページ3に含まれる内容の要旨
14. Use extra care when cleaning on stairs. 15. Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present. 16. EXTENSION CORDS: Use only three-wire extension cords which have three- prong grounding-type plugs and three-pole receptacles which accept the tool's plug. Replace or repair damaged or worn cord immediately. 17. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so
ページ4に含まれる内容の要旨
GROUNDING INSTRUCTIONS This appliance must be grounded. If it should malfunction or breakdown, ground- ing provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment- grounding conductor and grounding plug. The plug must be plugged into an ap- propriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. DANGER - Improper connection of the equipment-
ページ5に含まれる内容の要旨
1. When using this tool to collect dust into the dust bag Installing hose Attach the end of hose (the metal end) to the inlet. To attach it, align the protrusions on the inside of hose with the slots in the inlet, push the hose in and turn it clock- wise. Switch action This tool is equipped with a main switch and a sub-switch. To start the tool, both switches should be turned on. Main switch: To turn on the main switch, press the "ON" button. Press the "OFF" button to turn it off.
ページ6に含まれる内容の要旨
Overload protector The overload protector automatically cuts out to break the circuit whenever heavy work is prolonged. If this occurs, first turn off the main switch and unplug the tool. Then de- tach the hose and the inlet from the tool and remove the foreign matter clogging the fan. Now attach the inlet and the hose and press the restart button. CAUTION : Before pressing the restart button, always be sure to wait 20 seconds after the tool stopped. Operation Avoid using the tool with
ページ7に含まれる内容の要旨
2. When exhausting dust from indoors to outdoors Installing hoses Attach one hose to the inlet and another hose to the outlet in the same manner as mentioned in page. 5. CAUTION : The total length of exhaust hose and suc- ” tion hose should be less than 10 meters (32 feet). Otherwise the tool may become c I ogged. MAINTENANCE CAUTION : Always be sure that the tool is switched’off and unplugged before attempting to perform inspection or maintenance. The tool will stop when the carb
ページ8に含まれる内容の要旨
ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. When using this tool as blower Nozzle 81 Cover Part No. 191716-9 Installing cover and nozzle Attach the cover to the inlet and the hose to the outlet in the same manner as men- tioned i
ページ9に含まれる内容の要旨
If you connect this dust collector to a Makita planer or planer-jointer, you can perform clean, dust-free operation. To do so, use shaving hoods. CAUTION: .When dust or shavings exhausted from the planer or planer-jointer are large or wet, run the planer or the planer-jointer under light load. Otherwise the tools may become clogged. .The total length of exhaust hose and Table suction hose should be tess than the max. Max, length of hoses For Model length shown in the Table right. Other-
ページ10に含まれる内容の要旨
0 Y-joint assembly 0 Hood for Model 2012 Part No. 122342-3 Part No. 19201 0-2 (For Model 2030, 2030N) Can be used to collect chips and sawdust from auto-planer or jointer feed side by switching. 0 Hood for Model 2030N 0 Hood for Model 2004 Part No. 191 71 9-3 Part No. 191717-7 0 Hood for Model 2040 0 Hood for Model 2030 Part No. 191720-8 Part No. 191721-6 10
ページ11に含まれる内容の要旨
Oct -31-85 EN DUST COLLECTOR Model 410 Note: The switch, noise suppressor and other part configurations may differ from country to country. 11
ページ12に含まれる内容の要旨
July-17-'86 US ",'OM $.D DESCRIPTION ':,'OM ,& DESCRIPTION MACHINE ~ 1 1 Name Plafe 33 4 Mount 34 1 Over Current Relay KM 152 2 2 Rivet 0-5 3 2 Hex Nut M12 35 1 Relay Holder 36 2 Hex Nut M12 4 2 Washer 12 5 1 Switch Protector 37 1 Switch 1 38 1 Pan Head Screw M4x6 IWith Washeri 6 Relay Cover 7 1 Cowling 40 1 Sponge Sheet 1 41 1 Scroll '8 Inlet 1 9 4 Pan Head Screw M4x6 IWifh Washeri 42 Seal 10 1 Torsion Spring 10 43 1 Fan 130 44 1 11 1 Hex Nut M12 Lock Washer 12 12 1 Switch
