ページ1に含まれる内容の要旨
IMPORTANT NOTE!
This gauge has an hour meter and
odometer preset option available only
for the first 1.0 engine hour and 10 UTV-1000
miles (16km). See “ODO/HR
Multi Gauge for
PRESET” for instructions.
2004-2006 Yamaha Rhino
Operation menu
Left switch functions
Pressing the left switch during normal gauge operation will move through the below commonly viewed functions
for convenience.
00000.0 Odometer
12:00A Clock (hold left switch to set)
Setting clock:
ページ2に含まれる内容の要旨
INSTALLATION: 1. Disconnect the battery to prevent possible damage to the electrical system or gauge during install. 2. Remove the stock gauge or indicator panel (see service manual for removal instructions). The UTV gauge will mount in this mounting location. 3. Remove the seats, console/engine cover, front engine cover, and center floor/front drive shaft cover (refer to service manual). This allows access to sensor locations on the engine and wire routing locations. 4. Temperature send
ページ3に含まれる内容の要旨
6. Fuel sender installation (optional tube sender from Dakota Digital): a. To mount the sensor you will need to drill a hole in the fuel tank. Use a 1” hole saw, and drill a hole adjacent to the small dimple on the gas tank closest to the passenger side of the vehicle. Use a fuel safe sealant and coat the supplied cork gasket to provide a leak free seal from the tank to the sensor. Secure the sensor with the supplied stainless screws. DO NOT OVER TIGHTEN THE SCREWS. b. Attach the wir
ページ4に含まれる内容の要旨
Pulls up all values on speed and speed pulses in odometer Press Right switch to finish cal and save value ADJUST Adjust speed cal while driving ADJUST Each press of left switch toggles direction of adjustment, right switch to save and exit SRV MI (SRV KM) Sets value of service odometer set when service odometer is reset OFF ( OFF) Turns off the count down service odometer (default) 500 ( 800) Sets service to 500 mi or 800 km when resetting service
ページ5に含まれる内容の要旨
CLOCK± Adjust clock speed for accuracy -7 SEC Subtract 7 seconds from clock every 24 hrs … 0 SEC No adjustment to factory clock speed (default) … +7 SEC Add seven seconds to clock every 24 hrs St odo Allows presetting of odometer value on initial install (not available after 10 miles / 16km) Set hr Allows presetting of hour meter value on initial install (not available after 1.0 hrs) MAIN Returns to info menu DONE Leaves setup menu if selected
ページ6に含まれる内容の要旨
ODO/HR PRESET Within the first 10 miles (16 km) and 1.0 engine hours after first installing the gauge, the option is available for a ONE TIME preset of the odometer and hour meter to the reading(s) of the previous gauge. If this option is not used within the first 10 miles (16 km) or 1.0 engine hours or an incorrect reading is saved, the gauge will need to be returned to Dakota Digital for any odometer/hour meter adjustment. The procedure to preset the meters is as follows: 1. If setting od
ページ7に含まれる内容の要旨
TROUBLESHOOTING PROBLEM CAUSE SOLUTION Gauge does not light up Gauge has bad ground or power Check connections to wiring harness and check wiring harness and gauge wires for pinched or broken wires. Tach always stays blank Tach wire is not connected properly Check for good connection to alternator wire. Engine value set incorrectly Set Engine value to 12 for alternator (see setup) Tach reads incorrectly Engine value set incorrectly Set Engine value to 12 for alternator connection Speed
ページ8に含まれる内容の要旨
SERVICE AND REPAIR DAKOTA DIGITAL offers complete service and repair of its product line. In addition, technical consultation is available to help you work through any questions or problems you may be having installing one of our products. Please read through the Troubleshooting Guide. There, you will find the solution to most problems. Should you ever need to send the unit back for repairs, please call our technical support line, (605) 332-6513, to request a Return Merchandise Autho
