ページ1に含まれる内容の要旨
9. ACCEPTANCE CERTIFICATE
Image Intensifier Tube
Minimum Measured
Operation Manual
Resolution, lines/mm 30
Photocathode sensitivity, 400
integral, µA/ lm
Light amplification 20,000
Image Intensifier Tube Serial Number: _____________
Date of production: __________
Quality Inspector Signature: ____________
NIGHT VISION DEVICE
__NVS 7-2 __NVS 7-2SD __NVS 7-2HD __NVS 7-2WA
__NVS 7-2XT __NVS 7-3HD ___NVS 7-3
ページ2に含まれる内容の要旨
8. CUSTOMER SUPPORT IMPORTANT INFORMATION Should you experience any difficulties with your NEWCON OPTIK product, consult the enclosed manual. If the problem remains Read prior to activation unresolved, contact our customer support department at (416) 663-6963 You have just purchased a complicated electronic or toll free at 1-877-368-6666. Our operating hours are 9am-5pm, Monday - Friday, standard East time. At no time should equipment be device. To operate it properly, please rea
ページ3に含まれる内容の要旨
7. WARRANTY: CONTENTS NEWCON OPTIK warrants this product against defects in 1 Overview 5.1 Pre-starting procedures material and workmanship for one year from the date of the I) Application and 5.2 Testing of operation original date of consumer's purchase, but no more than 18 advantages of NVS 7 5.3 Operation at night months from the date of manufacturing. Longer warranty periods II) Warning 5.4 Optional lenses are available, subject to the terms of specific sales contract. Shoul
ページ4に含まれる内容の要旨
Precautions 6. TROUBLESHOOTING The device does not work. NVS 7 is a sophisticated precise optical instrument equipped Check that the battery is installed properly. with electronics. Check the charge of the batteries. Replace them if they are weak. Therefore, it should be handled with due care. • Try to avoid strong heat, direct sunlight, impacts, dust, moisture The image does not appear in focus. and sudden changes of temperatures. Keep in mind that, although Bring the inspected o
ページ5に含まれる内容の要旨
Press the button (2) to change the fixating point of the goggles 1. OVERVIEW during operation. Rotate the goggles with depressed button (2) until you hear the click. You can raise the unit up vertically for The NVS 7 type night vision is observational optico-electronic unobstructed vision without taking the helmet off. The unit will binoculars/goggles, intended for examining objects and orientation at automatically shut off in this position. (Note: this is an optional nighttime or d
ページ6に含まれる内容の要旨
2. COMPONENTS 5.5 Using the helmet mount (optional) NVS 7 can be equipped with an optional helmet mount. This NVS 7 is supplied with the following components: mount is customized for a particular type within the wide variety of existing helmet models. The mount is attached to a helmet PART QUANTITY with stripes. The goggles are fixed to the mount by a locking NVS 7 unit with 1x lens * 1 screw (1). Adjust the goggles position on your eye level with the Head gear* 1 screw (4).Then
ページ7に含まれる内容の要旨
OPERATION: 3. SPECIFICATIONS OF NVS 7 During daytime: It is allowed to turn on the goggles at daytime for a Model NVS 7-2 7-2SD 7-2HD 7-2XT 7-2WA 7-3HD short period of time, for testing purposes only. Lens cap must be 18 mm Gen. 2+ 25 mm 18 mm Image Intensifier Tube installed during this operation. The image will be fuzzy, and/or you will (IIT) Gen. 2+ Gen. 3 NC104322 NC064322NC064322NCXT4322 NC064331_25 N3064322 IIT model see 3 images. This is normal because of the
ページ8に含まれる内容の要旨
Main tube parameters 5.4 Installation and operation of optional lenses Image Intensifier Type 2+ / SD, 3 / HD INSTALLATION: (Generation/Grade) HD, XT Note: The following procedure is identical for 4x or 8x lenses . Unpack Photocathode operating diameter, mm 18 the 4x lens from the box. Turn off the NVS 7 goggles. Remove the Photocathode type S-25 GaAs rubber lens cap (6). Remove (unscrew) the original 1x lens, which is Photocathode sensitivity, min: included with the NVS 7 goggl
ページ9に含まれる内容の要旨
5.3 Operation at night 4. CONSTRUCTION You can use the device with the head gear or without it. 3 2 1 When used with the head gear, first adjust all the straps for 1. On-Off, I/R Switch individual head size. Take off the lens covers (6) from the lens 2. Mounting socket 4 (7). Turn on the device-using switch (1). In case of insufficient 3. Eyepiece adjustments lighting when observing an object, which is situated not far from 4. Eyepieces the viewer, turn on the I/R illuminator by tu
ページ10に含まれる内容の要旨
5. OPERATION INSTRUCTIONS 5.2 Testing of operation: When wearing the unit the eye-relief (the distance between your 5.1 Pre-starting procedures: eyes and the eyepieces) should be 15-22 mm. In order to achieve Unpack the device. In order to install the battery, first make sure this, loosen locking screw (8) and set a comfortable distance the switch (1) is in the OFF position. Unscrew the battery house between the eyes and the eyepieces; then rotate the locking cover (5), and install 2 fr
