ページ1に含まれる内容の要旨
8 Port 10/100Mbit/s Ethernet
Smart Switch with Fibre Uplink
-
Product User Guide
Introduction
This compact Tyco Electronics/AMPNetconnect auto-negotiating
Ethernet workgroup smart switch enables SOHO users and small
size workgroups to have high speed, low latency LAN connections
to the main network using a fibre link.
The automatic sensing of the connected 10/100Mbit/s data rate
and the detection of either a switch/hub or PC connected to the
Ethernet copper ports el
ページ2に含まれる内容の要旨
8 Port Ethernet Smart Switch With Fibre Uplink Features 8 Auto-sensing 10/100Base-T RJ-45 Ethernet ports 1 Fibre Uplink Port (100Base-FX Format) Full auto-MDI/MDI-X on all Ethernet copper ports removes the need for cross-over cables Meets IEEE 802.3, .3u and .3x Ethernet standards Uses store-and-forward switching to separate collision domains and provide abnormal packet filtering Console port enables basic management of the switch Supports up to
ページ3に含まれる内容の要旨
8 Port Ethernet Smart Switch With Fibre Uplink Front Panel The front panel of the switch has the LED indicators, the fibre uplink port and the RJ-45 Shielded/Unshielded Ethernet Ports. Figure 1 - Switch Front Panel Rear Panel The rear panel of the switch contains the IEC style power inlet connector and the console management connector. Figure 2 –Switch Rear Panel Ports RJ-45 Ports. These Ethernet RJ-45 ports support both shielded and unshielded cabling systems
ページ4に含まれる内容の要旨
8 Port Ethernet Smart Switch With Fibre Uplink Product Models The following table shows the model numbers of the switches that are available:- Product Part Number Switch with SC multimode connector 0-1591038-x Switch with ST multimode connectors 0-1591040-x Switch with MT-RJ multimode connector 0-1591042-x Switch with SC singlemode connector 0-1591044-x Table 1 - Product Codes Where –x is the code for the country. Consult the web site for the country code table. Installation
ページ5に含まれる内容の要旨
8 Port Ethernet Smart Switch With Fibre Uplink Completing The Installation When the switch has been installed as specified above, then the unit can be configured as detailed below:- 1. Connect the AC power cable to the switch. The green Power LED on the front panel of the switch should light. 2. Connect the Cat. 5/5e twisted pair cables from the network partner devices to the RJ-45 ports on the switch. When a network connection is obtained, the green LK/ACT LED associated with the port will lig
ページ6に含まれる内容の要旨
8 Port Ethernet Smart Switch With Fibre Uplink LED Indicators The diagnostic LED indicators located on the front panel of the switch provide real-time information about switch status. The following table describes the LED status and meaning. LED Colour Function Power Green Power on Green The UTP port is operating at 100Mbit/s 10/100 The UTP port is operating at 10Mbit/s or Off no partner device is attached Green Ethernet link pulses are present LK/ACT Blin
ページ7に含まれる内容の要旨
8 Port Ethernet Smart Switch With Fibre Uplink Configuring The Console Port The switch has a console port on the rear panel that can be used to provide simple control and configuration of the unit. The following port controls are available:- • Port Data Rate • Port Duplex Mode • Port Based VLAN Assignment A PC can be used to communicate with the switch using the console port. A terminal emulation program such as Windows Terminal or HyperTerminal is configured to the following settings:- • Com P
ページ8に含まれる内容の要旨
8 Port Ethernet Smart Switch With Fibre Uplink This entry screen is displayed when the connection is first established with the switch. Select the required option. Note that the options 3 and 4 are immediate and do not have any confirmation steps. Figure 4 - Entry Screen The port setting screen is selected by entering 1 in the entry menu. The screen then shows the current state of all the switch ports similar to the image to the right. To change a port setting, enter the port number (1..9) and
ページ9に含まれる内容の要旨
8 Port Ethernet Smart Switch With Fibre Uplink This screen enables the port speed and duplex mode to be controlled. The default is auto- negotiation which is the best method for most new networks. However, some legacy systems may need to use fixed duplex and speeds, so these can be applied on the switch using this menu. Select the option 1..5 to change port settings or select 6 to return to the main menu. Figure 6 - Port Configuration - 2 Simple port based VLANs can be created by selecting opti
ページ10に含まれる内容の要旨
8 Port Ethernet Smart Switch With Fibre Uplink Trouble Shooting Power 1. Verify that the AC power is present and that the external fusing is correct and compliant with national requirements. The green Power LED should be lit to indicate that the switch is powered correctly. Data Problems 1. Ensure that the Ethernet partner device (switch, router, NIC etc) connected to the RJ-45 UTP port of the switch is set for auto- negotiation. If this Ethernet partner device does n
ページ11に含まれる内容の要旨
8 Port Ethernet Smart Switch With Fibre Uplink Fibre Uplink Port Specifications The switch has a 100Base-FX optical fibre uplink port that operates at the 1310nm optical wavelength for both the multimode and singlemode models. The fibre size used for multimode links is 50/125 or 62/125 micron. The fibre size used for singlemode links is 8/125 or 9/125 micron. The maximum distance between any two fibre optic devices is determined by a number of factors including op
ページ12に含まれる内容の要旨
8 Port Ethernet Smart Switch With Fibre Uplink Product Specifications Standards IEEE 802.3 10Base-T Ethernet Compliance IEEE 802.3u 100 BASE-TX Fast Ethernet IEEE 802.3u 100 Base-FX Fast Ethernet ANSI/IEEE standard 802.3 N-way Auto-Negotiation Max Forwarding 14,880 pps Ethernet port (10Mbit/s) Rate 148,800 pps Fast Ethernet port (100Mbit/s) Packet Size 64 to 1522 Bytes LED Indicators Power, Speed, Link Activity, Duplex/Coll. Ethernet LAN 2-pair UTP/STP Cat. 3, 4, 5 cable
