ページ1に含まれる内容の要旨
model g0634Xp
polar bear series
12" Jointer/planer
manual insert
Congratulations on your purchase of the Model g 0634Xp 12" Jointer/planer! t he Model g 0634Xp is the
same machine as the Model g 0634 but with a "cool" new look, a different type of spiral cutterhead, and
a new end-mounting fence. Except for the differences noted in this insert, all other content in the Model
g 0633/g 0634 manual applies to this machine. Before operating your new machine, you MUst read and
understand this ins
ページ2に含まれる内容の要旨
stand assembly parts breakdown REF PART # DESCRIPTION REF PART # DESCRIPTION 1 P0634XP001 FRAME 5 P0634XP005 SIDE OPENING COVER 1-1 P0634XP001-1 HINGE SHAFT BRACKET RIGHT 44 P0634XP044 HEX WRENCH 3/32 1-2 P0634XP001-2 HINGE SHAFT BRACKET LEFT 802 P0634XP802 MACHINE ID LABEL 2 P0634XP002 DRIVE SHAFT COVER 808 PPAINT-24 PB WHITE TOUCH-UP PAINT 3-1 P0634XP003-1 COVER 810 P0634XP810 MODEL # LABEL 4 P0634XP004 DOOR 811 PLABEL-75 POLAR BEAR LOGO 2-1/2 X 9-1/2 table assembly parts breakdown
ページ3に含まれる内容の要旨
cutterhead & motor parts breakdown REF PART # DESCRIPTION REF PART # DESCRIPTION 201 P0634Z201V2 SP CUTTERHD 12" 10-32 V2.09.09 204-1A P0634XP204-1A PLANER DUST PORT 201-1 H9893 INDEXABLE CUTTER 15 X 15 X 2.5 215 P0634XP215 DUST CHUTE 201-2 PFH32 FLAT HEAD TORX 10-32 X 1/2 215-6 P0634XP215-6 BRACKET 201-3 P0634Z201-3 TORX T-HANDLE WRENCH 1/4 215-7 P0634XP215-7 PLATE 201-4 P0634Z201-4 TORX BIT T-25 225 P0634XP225 GUARD -3- Model g 0634Xp (Mfg. 4/11+)
ページ4に含まれる内容の要旨
fence/guard parts breakdown REF PART # DESCRIPTION REF PART # DESCRIPTION 600 P0634XP600 COMPLETE FENCE ASSEMBLY 618 PW07 FLAT WASHER 5/16 601 P0634XP601 FENCE 619 P0634XP619 FENCE ANGLE SUPPORT 602 P0634XP602 FENCE FIXED PLATE 620 PCAP03 CAP SCREW 5/16-18 X 1 603 P0634XP603 LEFT FENCE CAP 621 P0634XP621 STUD-UDE 3/8-16 X 2-1/2 1/2 / 3/4RH 604 P0634XP604 RIGHT FENCE CAP 623 PN05 HEX NUT 1/4-20 605 PHTEK23 TAP SCREW #10 X 1/2 624 PSS10 SET SCREW 1/
ページ5に含まれる内容の要旨
MACHINE DATA SHEET MODEL G0634XP POLAR BEAR SERIES JOINTER/PLANER w/SPIRAL CUTTERHEAD Product Dimensions: Shipping Dimensions: Electrical: Motors: Main Main Specifications: Fence Information Cutting Capacities (Jointer) Model G0634XP Page
ページ6に含まれる内容の要旨
Cutting Capacities (Planer) Cutterhead Information Table Information (Jointer) Table Information (Planer) Construction Other Infomation Other Specifications: Features: Model G0634XP Page 2 of
ページ7に含まれる内容の要旨
section 2: po Wer supply availability circuit requirements for 220v nominal voltage .............................. 220v /240v c ycle ..........................................................60 hz p
ページ8に含まれる内容の要旨
grounding instructions
ページ9に含まれる内容の要旨
f ence t ilting: t he tilt knob (f igure 5) secures basic Jointer the fence at any position in the available range. Fence stops set the fence at 90° or 45° outward. c ontrols t he tilt knob must be tightened before jointing. see page 10 in this insert for more detail on adjusting the fence stops. All basic controls used during routine jointer oper- ations on the g 0634Xp are the same as those t o move the fence to 45° outward, loosen the tilt described on pages 22–23 of the manual except
ページ10に含まれる内容の要旨
l ubrication setting f ence stops Follow all lubrication instructions outlined on the fence stops simplify the task of adjusting the pages 35–36 of the manual. l ubricate the fence to 45˚ and 90˚. g 634Xp fence with multi-purpose grease, as shown in f igures 7–8. t ools needed Qty 45° square ........................................................ 1 90° square ........................................................ 1 sliding Bevel ...................................................... 1 Wr
ページ11に含まれる内容の要旨
to set the 45° fence stop: r eplacing c arbide 1. loosen the fence tilt knob and position the inserts fence against the 45° stop bolt. 2. loosen the lock nut on the 45˚ fence stop t ools needed: Qty screw (see figure 10). t-handle Wrench w/t-25 torx Bit ..................... 1 the cutterhead is equipped with 32 indexable car- 45° stop screw bide inserts. Each insert can be rotated to reveal any one of its four cutting edges. therefore, if one cutting edge becomes dull or damaged, simply r
ページ12に含まれる内容の要旨
4. Clean all dust and dirt off the insert and the a ccessories cutterhead pocket from which the insert was removed, and replace the insert so a fresh, sharp edge is facing outward. h9893—carbide inserts (10 pk) for g0634Xp t hese indexable carbide inserts can be rotated to note: Proper cleaning is critical to achieving provide four factory sharp edges before replace- a smooth finish. Dirt or dust trapped between ment. size: 15 x 15 x 2.5mm. the insert and cutterhead will slightly raise th
