ページ1に含まれる内容の要旨
MODEL G0675
10" JOINTER/PLANER
COMBO MACHINE
OWNER'S MANUAL
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
Table of Contents SECTION 6: MAINTENANCE ......................... 32 INTRODUCTION ............................................... 2 SECTION 7: SERVICE ................................... 37 SECTION 1: SAFETY ....................................... 6 SECTION 2: CIRCUIT REQUIREMENTS ...... 10 SECTION 3: SETUP ....................................... 11 SECTION 8: WIRING ..................
ページ4に含まれる内容の要旨
INTRODUCTION Manual Accuracy Functional Overview your machine may not exactly match the manual www.grizzly.com Contact Info
ページ5に含まれる内容の要旨
Identification Figure 1. A. M. B. N. C. O. D. P. E. Q. F. R. G. S. H. T. I. U. J. V. K. W. L. X. Y.
ページ6に含まれる内容の要旨
Machine Data Sheet MACHINE DATA SHEET MODEL G0675 JOINTER/PLANER COMBINATION MACHINE Product Dimensions: Shipping Dimensions: Electrical: Motors: Main Main Specifications: Fence Information Cutting Capacities (Jointer) Cutting Capacities (Pla
ページ7に含まれる内容の要旨
Knife Information (Jointer) Cutterhead Information Table Information (Jointer) Table Information (Planer) Construction Other Infomation Other Specifications: Features:
ページ8に含まれる内容の要旨
Safety Instructions for Machinery
ページ9に含まれる内容の要旨
ページ10に含まれる内容の要旨
Additional Safety Instructions for Jointers 7. CUTTING LIMITATIONS. 1. JOINTER KICKBACK. DO NOT 8. JOINTING WITH THE GRAIN 2. CUTTERHEAD ALIGNMENT. 9. KEEPING GUARDS IN PLACE. 3. PUSH BLOCKS. 10. PROPER CUTTING. 4. WORKPIECE SUPPORT. 11. USING GOOD STOCK.
ページ11に含まれる内容の要旨
Additional Safety Instructions for Planers 1. KICKBACK. 8. CUTTING LIMITATIONS. DO NOT 2. REACHING INSIDE PLANER. 9. CLEAN STOCK. 3. INFEED CLEARANCE SAFETY. 4. BODY POSITION WHILE OPERATING. 10. REMOVING JAMMED WORKPIECES. 5. PLANING CORRECT MATERIAL. 11. DULL/DAMAGED KNIVE
ページ12に含まれる内容の要旨
SECTION 2: CIRCUIT REQUIREMENTS Power Connection Device 220V Operation Figure 2 Serious personal injury could occur if you connect the machine to power before com- pleting the setup process. DO NOT connect the machine to the power until instructed later in this manual. Electrocution or fire could result if machine is not Figure 2 grounded and installed in compliance with electrical Extension Cords codes. Compliance MUST be verified by a qualified
ページ13に含まれる内容の要旨
SECTION 3: SETUP Items Needed for This machine presents Setup serious injury hazards to untrained users. Read through this entire manu- al to become familiar with the controls and opera- tions before starting the machine! Description Qty Wear safety glasses dur- ing the entire setup pro- cess! This machine and its com- ponents are very heavy. Unpacking Get lifting help or use power lifting equipment such as a forklift to move
ページ14に含まれる内容の要旨
Inventory Clean Up Figure 4 Note: If you can't find an item on this list, check the mounting location on the machine or examine For optimum performance, clean all moving the packaging materials carefully. Occasionally parts or sliding contact surfaces. we pre-install certain components for shipping purposes. Box 1: (Figure 3) Qty A. B. C. D. Gasoline and petrole
ページ15に含まれる内容の要旨
Site Considerations Moving & Placing Base Unit Floor Load Machine Data Sheet The Model G0675 is a heavy machine. Serious personal injury may occur if safe moving methods Placement Location are not used. To be safe, get assistance and use power equipment to move the shipping crate and remove the machine from Figure 5 the crate. Figure 6 Figure 6. Figure
ページ16に含まれる内容の要旨
Bolting to Concrete Floors Mounting to Shop Figure 9 Floor NOTICE To mount the base to the floor: Anchor studs are stronger and more per- manent alternatives to lag shield anchors; 1. however, they will stick out of the floor, Figure 7 which may cause a tripping hazard if you decide to move your machine. Figure 7. Figure 9 2. 3. Figure 8 Figure 8. 4. 5.
ページ17に含まれる内容の要旨
Tip: Try tightening one cap screw several turns, Assembly then repeat with other until both are tight. 3. Figure 12 Test Run Page 18 Page 22 To assemble the machine: 1. Figure 10 Figure 12. Figure 11 4. Figure 10. Figure 13 2. Figure 11 Figure 13. Figure 11.
ページ18に含まれる内容の要旨
Dust Collection DO NOT operate the Model G0675 with- out an adequate dust collection system. This machine creates substantial amounts of wood dust while operating. Failure to use a dust collection system can result in long- term respiratory illness. Recommended CFM at Dust Port: 400 CFM Figure 15. Do not confuse this CFM recommendation with the rating of the dust collector. To determine the CFM at the dust port, you must consider these Page 22 Planer variables: (1) CFM rat
ページ19に含まれる内容の要旨
6. Setting Outfeed Figure 17 Table Height Figure 17. To set the outfeed table height: 7. 1. Figure 18 . 2. Figure 3. 18 4. Replacing Flat Drive Belt, Steps 3-4 Page 33 5. Figure 16 Figure 18. Figure 16. Checking Outfeed Table Parallelism Page 39 8.
ページ20に含まれる内容の要旨
Test Run Step 10 10. Planer Operation Setup, Steps 1-5 Troubleshooting Page 37 Page 22, 11. Figure 19 To test run the machine: 1. 2. 3. 4. Figure 19. 5. ON 12. ON 6. 7. OFF
