ページ1に含まれる内容の要旨
MODEL G0677
24" PLANER/SANDER
OWNER'S MANUAL
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
Table of Contents INTRODUCTION ............................................... 2 SECTION 7: SERVICE ................................... 39 SECTION 1: SAFETY ....................................... 8 SECTION 2: CIRCUIT REQUIREMENTS ...... 11 SECTION 3: SETUP ....................................... 13 SECTION 8: WIRING ...............................
ページ4に含まれる内容の要旨
INTRODUCTION Manual Accuracy Functional Overview ON your machine may not exactly match the manual www.grizzly.com OFF Contact Info
ページ5に含まれる内容の要旨
Controls & Features Figure 1. A. J. B. Page 24 K. C. L. D. M. E. N. F. O. G. P. H. Q. I.
ページ6に含まれる内容の要旨
Figure 2. Figure 3. A. J. B. K. C. L. D. M. E. N. F. O. G. P. H. I.
ページ7に含まれる内容の要旨
Machine Data Sheet MACHINE DATA SHEET MODEL G0677 24" DOUBLE HEAD PLANER SANDER Product Dimensions: Shipping Dimensions: Electrical: Motors: Sanding Drum/Cutterhead Conveyor Feed
ページ8に含まれる内容の要旨
Table Elevation Feed Main Specifications: Operation Information Drum Information Cutterhead Information Construction Other Related Infomation
ページ9に含まれる内容の要旨
Other Specifications: Features:
ページ10に含まれる内容の要旨
Safety Instructions for Machinery
ページ11に含まれる内容の要旨
ページ12に含まれる内容の要旨
Additional Safety for Planer/Sanders 1. INSTRUCTION MANUAL. 8. CLEAN STOCK. 2. REACHING INSIDE MACHINE. 9. REMOVING JAMMED WORKPIECES. 10. DULL/DAMAGED INSERTS. 3. INFEED/OUTFEED AREA. 11. POWER AND AIR DISCONNECT. 4. LOOKING INSIDE PLANER. 12. WORKPIECE FEEDING.
ページ13に含まれる内容の要旨
SECTION 2: CIRCUIT REQUIREMENTS Minimum Cord Requirements 220/440V Operation Serious personal injury could occur if you Power Connection Device connect the machine to the power source before you have completed the setup pro- cess. DO NOT connect the machine to the Figure 4 power source until instructed after setup. Electrocution or fire could result if this machine is not installed to code. You MUST ensure compliance by checking with a quali- fied electri
ページ14に含まれる内容の要旨
4. 440V Conversion Figure 6 Page 86 Accessories Page 34 Phase Converter Page 11 Set to18A Set to 1.7A Figure 6 To rewire the Model G0677 for 440V opera- 5. tion: 1. Pages 68 70. Note: The reference wiring diagrams on 2. Pages 68 70 current at the time of Figure 1 Page 3 printing, but always use the wiring diagram provided inside th
ページ15に含まれる内容の要旨
SECTION 3: SETUP Setup Safety Items Needed for Setup This machine presents serious injury hazards to untrained users. Read through this entire manu- Description Qty al to become familiar with the controls and opera- tions before starting the machine! Wear safety glasses dur- ing the entire setup pro- cess! Unpacking This machine and its com- ponents are very heavy. Use power lifting equip- please imme- men
ページ16に含まれる内容の要旨
Inventory Note: If you can't find an item on this list, check the mounting location on the machine or examine the packaging materials carefully. Occasionally we pre-install certain components for shipping purposes. Crate Contents: (Figures 7 & 8) Qty Figure 7 A. B. C. D. E. F. G. H. I. J. K. L. M. N. O. P. Figure 8
ページ17に含まれる内容の要旨
Clean Up Figure 10 Figure 9 For optimum performance, clean all moving parts or sliding contact surfaces. Gasoline and petroleum products have low flash points and can explode or cause fire if used to clean machinery. DO NOT use these products to clean the machinery. Many cleaning solvents are toxic if inhaled. Minimize your risk by only using these pro
ページ18に含まれる内容の要旨
To access the spiral cutterhead: Site Considerations 1. Figure 10 Page 15 Floor Load Machine Data Sheet 2. Figure 10 3. Placement Location 4. Figure 10 Figure 12 Figure 11 Figure 11 5. Figure 12. 6. Children and visitors may be seriously injured if unsuper- 7. vised around this ma
ページ19に含まれる内容の要旨
Moving & Placing Mounting to Shop Planer/Sander Floor The Model G0677 is a heavy machine. Serious personal injury may occur if safe moving methods are not used. To be safe, get assistance and use power equipment to move Bolting to Concrete Floors the shipping crate and remove the machine from the pallet. Figure 14 To move and place your planer/sander: 1. 2. 3. Figu
ページ20に含まれる内容の要旨
Air Hose Dust Collection To install the air line: 1. Figure 15 Recommended CFM @ Machine: 2500 CFM Do not confuse this CFM recommendation with the rating of the dust collector. To determine the CFM at the dust port, you must consider these variables: (1) CFM rating of the dust collector, (2) hose type and length between the dust col- lector and the machine, (3) number of branches or wyes, and (4) amount of other open lines throughout the system. Explaining how to cal- Figu
