ページ1に含まれる内容の要旨
MODEL G1033X
20" 5HP SPIRAL CUTTERHEAD
PLANER
OWNER'S MANUAL
Copyright © FEB r UAry , 2006 By g rizzly ind Ustri Al, in C., rE vis Ed April, 2010 (tr)
WARNING: NO PORTION Of THIS MANUAL MAy b E REPRODUCED IN ANy SHAPE
OR fORM WITHOUT THE WRITTEN APPROvAL Of G RIzz Ly INDUSTRIAL, INC.
For mod Els m An UFACt Ur Ed s in CE 4/10 #Bl 7969 print Ed in Chin A
ページ2に含まれる内容の要旨
This manual provides critical safety instructions on the proper setup, operation, maintenance and service of this machine/equipment. Failure to read, understand and follow the instructions given in this manual may result in serious personal injury, including amputation, electrocution or death. The owner of this machine/equipment is solely responsible for its safe use. This responsibility includes but is not limited to proper installation in a safe environment, personnel training and usage
ページ3に含まれる内容の要旨
Table of Contents INTRODUCTION ............................................... 2 SECTION 5: ACCESSORIES ......................... 22 manual Accuracy ........................................... 2 SECTION 6: MAINTENANCE ......................... 24 Contact info.................................................... 2 schedule ...................................................... 24 identification ................................................... 3 Cleaning .........................................
ページ4に含まれる内容の要旨
INTRODUCTION Manual Accuracy Contact Info We are proud to offer this manual with your new We stand behind our machines. If you have any machine! We've made every effort to be exact service questions, parts requests or general ques- with the instructions, specifications, drawings, tions about the machine, please call or write us at and photographs of the machine we used when the location listed below. writing this manual. However, sometimes we still make an occasional mistake. Grizzly Industri
ページ5に含まれる内容の要旨
Identification A B C J d A E h F o v g i i h K l figure 1. g1033X identification. A. Control Box and panel b. return rollers C. table height handwheel D. gearbox E. table height scale f. speed Control Knob G. table locks H. lifting Bar I. Extension Wing J. dust hood K. v-Belt Cover L. motor and magnetic switch Access panel -3- model g 1033X (mfg. since 4/10)
ページ6に含まれる内容の要旨
Machine Data Sheet MACHINE DATA SHEET Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G1033X 20" 5 HP SPIRAL CUTTERHEAD PLANER Product Dimensions: Weight.............................................................................................................................................................. 875 lbs. Length/Width/Height...............................................................................................................
ページ7に含まれる内容の要旨
Cutterhead Info Cutterhead Type........................................................................................................................................ Spiral Cutterhead Dia....................................................................................................................................... 3-1/4 in. No. Of Cutter Spirals......................................................................................................................................... 4 No.
ページ8に含まれる内容の要旨
SECTION 1: SAf ETy For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. Indica
ページ9に含まれる内容の要旨
safety instructions for m achinery 7. Only allOw trained and prOp- 16. remOve chucK K eys O r adJustinG erly supervised pers Onnel t O tOOls. Make a habit of never leaving Operate machinery. Make sure chuck keys or other adjustment tools in/on operation instructions are safe and clearly the machine—especially near spindles! understood. 17. damaGed machinery. Check for bind- 8. Keep children /visit Ors away . ing or misaligned parts, broken parts,
ページ10に含まれる内容の要旨
Additional Safety for Planers 1. INSTRUCTION MANUAL: t his machine 7. CUTTING LIMITATIONS: the planer may presents significant safety hazards to kick out a workpiece at the operator or be untrained users. read/understand this entire damaged if pushed beyond these limits: 5 manual before starting the planer. • maximum depth of Cut .................... ⁄64" 1 • minimum Board l ength ....................7 ⁄2" 1 2. INfEED CLEARANCE SAfETy: the infeed • minimum Board t hickness ................ ⁄4"
ページ11に含まれる内容の要旨
SECTION 2: CIRCUIT REQUIREMENTS Power Connection Device 220v Single-Phase t he type of plug required to connect your machine to power depends on the type of service you cur- rently have or plan to install. We recommend using the plug shown in f igure 2. Serious personal injury could occur if you connect the machine to the power source L6-30 LOCKING before you have completed the set up pro- RECEPTACLE cess. DO NOT connect the machine to the power source until instructed to do so. Before plac
ページ12に含まれる内容の要旨
SECTION 3: SET UP Items Needed for This machine presents Set Up serious injury hazards to untrained users. Read through this entire manu- t he following items are needed to complete the al to become familiar with set up process, but are not included with your the controls and opera- machine: tions before starting the machine! Description Qty • straightedge 4' (or longer) .......................... 1 • r otacator (see Page 21) ............................ 1 • phillips s crewdriver .......
ページ13に含まれる内容の要旨
Inventory A After all the parts have been removed from the crate, you should have the following items: box Inventory (f igure 3) Qty B d A. planer Unit .................................................. 1 C b. d ust h ood .................................................. 1 C. t able Extension Wings ............................... 2 D. h andwheel ................................................. 1 figure 3. planer box inventory. E. h ardware and t ools (n ot s hown) • t -h andle Wrench t -25 ..
ページ14に含まれる内容の要旨
Hardware Recognition Chart -12- model g 1033X (mfg. since 4/10)
ページ15に含まれる内容の要旨
Cleanup Gasoline and petroleum products have low flash The unpainted surfaces of your machine are points and can explode coated with a heavy-duty rust preventative that or cause fire if used to prevents corrosion during shipment and storage. clean machinery. Avoid using these products This rust preventative has been your machine's to clean machinery. close ally and guardian since it left the factory. If your machine arrived to you free of rust, then be thankful that the rust preventat
ページ16に含まれる内容の要旨
Site Considerations Weight Load Physical Environment Refer to the Machine Data Sheet for the weight The physical environment where your machine of your machine. Make sure that the surface upon is operated is important for safe operation and which the machine is placed will bear the weight the longevity of its components. For best results, of the machine, additional equipment that may be operate this machine in a dry environment that is installed on the machine, and the heaviest work- free fr
ページ17に含まれる内容の要旨
Moving & Placing Extension Wings Planer Components and Hardware Needed: Qty t able Extension Wings ...................................... 2 h ex Bolts m8-1.25 x 25 ..................................... 6 set s crews m8-1.25 x 20 .................................. 6 The Model G1033X is a To attach the table extension wings: heavy machine. Serious personal injury may occur 1. With the help of an assistant, attach the table if safe moving methods extension wings to the planer table (figure 7)
ページ18に含まれる内容の要旨
Handwheel Dust Hood Components and Hardware Needed: Qty Components and Hardware Needed: Qty h andwheel......................................................... 1 d ust h ood ......................................................... 1 h andwheel Bushing .......................................... 1 Flange Bolts m6-1 x 12 ..................................... 6 h andwheel h andle ............................................ 1 h ex nut m12-1.75 .............................................. 1 Flat W
ページ19に含まれる内容の要旨
Gearbox Oil Level Connecting to Power now is the time to connect your planer to the Before starting your machine for the first time, power source. make sure you have read CIRCUIT make sure the gearbox has oil. the proper oil REQUIREMENTS on Page 9, before doing so. level is just even with the bottom of the fill plug hole. the gearbox uses 80W-90W gear oil. To check the gearbox oil level: Test Run 1. Using a 14mm wrench or socket, remove the gearbox fill plug (figure 11). Loose hair and clo
ページ20に含まれる内容の要旨
Tighten v-belts Recommended Adjustments the final step in the set up process must be done after approximately 16 hours of operation. during For your convenience, the adjustments listed this first 16 hours, the v-belts will stretch and seat below have been performed at the factory and into the pulley grooves. After this 16 hours, the v- no further setup is required to operate your belts must be tensioned or your belts will slip and machine. burn out. refer to Page 23 when you are ready t
