ページ1に含まれる内容の要旨
Mo de l No.
- 8097 -
p/ n 1 0 83 2 2
Specifications
Height: 60” (22” packed)
▪
Width: 45”
▪
▪ Depth: 80” (36” packed)
Weight: 53 lbs.
▪
Instruction p/n 102476
▪
- Clam Customer Servi ce Information -
NOTICE!! Once used, this shelter cannot be returned to the store. If you have a
warranty claim, have your sales receipt ready and contact Clam Corporation
Customer Service by email inquiry or direct by calling:
Customer Service Hrs: - 9am to 4pm,
ページ2に含まれる内容の要旨
- Parts Li st - ITEM NO. PART NUMBER DESCRIPTION QTY. 1 101070 TUBE, PRO CANOPY HOOP 3 2 101079 TUBE, PRO PORCH HOOP 1 3 101096 MOLDING, PRO U-CHNL 1 4 101463 ASSY, GREY PADDED SEAT 1 5 101466 HAMMOCK, ACCESSORY 1 6 102495 BASE, PRO 08-09 1 7 102502 TUBE, PRO SEAT RAIL SUPPORT 1 8 102433 TENT, 08/09 PRO 1 9 101042 BRKT, RH CANOPY 1 10 101043 BRKT, LH CANOPY 1 11 101069 POLE CANOPY 6 12 101078 TUBE, PORCH 2 13 101146 CHANNEL, 8.78 ALUM EXT 2 14 101420 BRKT, FRONT RETAINER 1 1
ページ3に含まれる内容の要旨
- Parts Di agram - 3
ページ4に含まれる内容の要旨
- Step One - 4
ページ5に含まれる内容の要旨
- Step Two - 5
ページ6に含まれる内容の要旨
- Step Three - 6
ページ7に含まれる内容の要旨
- Step Four - 7
ページ8に含まれる内容の要旨
- Step Five - Latch Clip (p/n 102512) Rear Se at Bracket (p/n 102430) 8
ページ9に含まれる内容の要旨
- Step Six - 1” x 2” Rectan gular Support Tube (p/n 102502) Pro Base (p/n 102495) 9
ページ10に含まれる内容の要旨
- Step Seven - 10
ページ11に含まれる内容の要旨
- Step Ei ght - Slide the canopy hoop poles onto the canopy poles until the spring buttons engage the holes near the ends of each canopy hoop pole. 11
ページ12に含まれる内容の要旨
- Step Nine - Drape the tent over the supported hoops then go inside and spread out the canopy hoop poles, attaching the roof velcro as you go. Pro Tent (p/n 102433) 12
ページ13に含まれる内容の要旨
- Step Ten - Feed the length of the porch hoop pole through the porch hoop sleeve sewn on the Tent. Slide the porch hoop pole onto the porch poles, engaging the second hole position. Attach the porch velcro on each side of the tent. 13
ページ14に含まれる内容の要旨
- Step Eleven - To “ set” the tent, grasp the tent material at the rear of the shelter and pull it downward. Observe the porch area of the tent lifting accordingly as you pull. When the U-Channel molding is correctly installed, the porch hoop pole will lightly touch the floor. To achieve this condition, start by finding the center of the molding. From behind the unit, pull the midpoint of the tent downward and fold the tent material under the base lip. Press the midpoint of the moldin
ページ15に含まれる内容の要旨
- Step Tw el ve - Angle the seat assembly slightly while placing the bottom lip of the front seat bracket under the outside edge of the base lip. Tilt the complete assembly downward so that the rear seat bracket lands upon the support tube. Reach under the rear seat bracket and slide the latch clip outwards and then up against the underside of the support tube. Squeeze the latch clip into the horizontal slot of the rear seat bracket. Secure the position of the latch clip by pus
ページ16に含まれる内容の要旨
- Tips for Use - Folding and transporting your Fish Trap is easy: Unsnap the rear spreader pole and lay it in the bottom of the base. ▪ Push the spring buttons and retract each hoop, starting with the rear hoop and working towards the ▪ front. Rotate all retracted hoops to the resting position. Tuck the tent into the base and between the hoops so that no material is left hanging on the ground for transport. Cover with the Travel Cover* (an optional but recommended accessory to help pr