ページ1に含まれる内容の要旨
MINUET 300
User’s Manual
1
ページ2に含まれる内容の要旨
TABLE OF CONTENTS Minuet 300 ...................................................... 2 Setting Up ........................................................ 2 Motherborad Installation .................................. 2 Power/LED Connections .................................. 3 Connecting Th e USB Ports .............................. 3 Connecting Th e IEEE 1394 (FireWire®, i.Link®) Port ................................... 4 Connecting Th e Audio Ports ............................ 4 Drive Installat
ページ3に含まれる内容の要旨
The high quality of our products is assured by a continuous process of refi nement of their techni- cal features. Therefore, it is possible that your product may differ in some respect from the descrip- tions contained in this manual. This is not a problem– it is an improvement. All features, descrip- tions and illustrations contained herein are valid as of the date of publication. Disclaimer This manual is intended only as a guide for Antec’s Computer Enclosures. For more comprehensive instruct
ページ4に含まれる内容の要旨
2. Line up your motherboard with the standoff holes, and determine which ones line up and remember where they are. Not all motherboards will match with all of the provided screw holes, and this is not necessary for proper functionality. (In other words there will likely be extra holes.) Some standoffs may be pre-installed for your convenience. 3. Lift up and remove your motherboard. 4. Screw in the brass standoffs to the threaded holes that line up with your motherboard’s mount
ページ5に含まれる内容の要旨
CONNECTING THE IEEE 1394 (FIREWIRE , I.LINK ) PORT ® ® You will fi nd a single 10-pin connector on a cable attached to the front IEEE 1394 connection. This is an Intel standard connector, which is keyed so that it can’t be accidentally reversed as long as it is connected to a proper Intel standard motherboard header. Connect the 10-pin connector to your motherboard header so that the blocked pin fi ts over the missing header pin. Note: Please check your motherboard manual for your IEEE 1394 hea
ページ6に含まれる内容の要旨
2. Lift up and slide the drive cage from the case. 3. Place the cage upside down on a fl at surface. 4. Note: You must install the external devices fi rst, before installing the internal 3.5” device. 5. Slide the external 5.25” device into the drive cage from the front. Since the drive cage is upside down, your drive should be too so that it will be properly orientated once the cage is installed in the Minuet II. 6. Align the bottom rear screw holes (one at each side) o
ページ7に含まれる内容の要旨
Specifi cations: Size: 80 x 80 x 25.4mm Rated Voltage: 12V Operating Voltage: 10.2V ~ 13.8V Speed Input Current Air Flow Static Pressure Acoustical Input Power Noise High 0.2A 0.96 m³ / min 3.04 mm-H2O 30 dBA 2.4W 2600 RPM (Max.) (34 CFM) (0.12 inch-H2O) Medium 0.15A 0.74 m³ / min 1.79 mm-H2O 24 dBA 1.8W 2000 RPM (26 CFM) (0.07 inch-H2O) Low 0.1A 0.55 m³ / min 1.00 mm-H2O 18 dBA 1.2W 1500 RPM (20 CFM) (0.03inch-H2O) Top Panel: Minuet 300 comes with a vented top panel for maximum cooling capacity
ページ8に含まれる内容の要旨
1 2 3 4 14 13 12 5 6 7 8 11 9 Minuet 300 - Explorer Description # Description # Description 1 Thumbscrews 8 3.5” Drive Bay Cover 2 Top Panel with Vent 9 Front Bezel 3 Power Supply 10 5.25” Drive Bay Cover 4 Flip Up Drive Cage 11 Front PCB Assembly 5 Power Switch/Cable 12 Case 6 Power LED/Cable 13 Expansion Slot Covers 7 HD LED/Cable 14 I/O Panel 7
ページ9に含まれる内容の要旨
Antec, Inc. 47900 Fremont Blvd. Fremont, CA 94538 tel: 510-770-1200 fax: 510-770-1288 Antec Europe B.V. Sydneystraat 33 3047 BP Rotterdam The Netherlands tel: +31 (0) 10 462-2060 fax: +31 (0) 10 437-1752 Customer Support: US & Canada 1-800-22ANTEC customersupport@antec.com Europe +31 (0) 10 462-2060 europe.techsupport@antec.com www.antec.com Antec Quality 3-Year parts and labor warranty (A3Q) See details at: http://www.antec.com/warranty.php © Copyright 2005Antec, Inc. All rights reserved. All
