ページ1に含まれる内容の要旨
CHAPTER11
Change Card Settings
This chapter explains how to change transmission settings on cards in a Cisco ONS 15600.
Before You Begin
As necessary, complete the “NTP-E57 Document Existing Provisioning” procedure on page 7-2.
Before performing the following procedures, investigate all alarms and clear any trouble conditions.
Refer to the Cisco ONS 15600 Troubleshooting Guide as necessary.
This section lists the chapter procedures (NTPs). Turn to a procedure for applicable tasks (DLPs).
1.
ページ2に含まれる内容の要旨
Chapter 11 Change Card Settings NTP-E157 Provision a Multirate PPM NTP-E157 Provision a Multirate PPM Purpose This procedure provisions a multirate pluggable port modules (PPMs) in CTC. Tools/Equipment None Prerequisite Procedures NTP-E147 Install the ASAP Card, page 2-5 DLP-E211 Install the ASAP 4PIO Modules, page 18-12, as needed DLP-E215 Install an SFP, page 18-14, as needed Required/As Needed Required Onsite/Remote Onsite or remote Security Level Provisioning or higher Step 1 Complete
ページ3に含まれる内容の要旨
Chapter 11 Change Card Settings NTP-E151 Provision an Optical Line Rate NTP-E151 Provision an Optical Line Rate Purpose This procedure provisions the line rate on a multirate pluggable port module (PPM). Single-rate small-form factor pluggables (SFPs) or 4-port I/O modules (4PIOs) do not need line rate provisioning. Tools/Equipment None Prerequisite Procedures NTP-E148 Preprovision an SFP Slot, page 2-8 or NTP-E157 Provision a Multirate PPM, page 11-2 Required/As Needed Required Onsite/R
ページ4に含まれる内容の要旨
Chapter 11 Change Card Settings NTP-E150 Change the Optical Line Rate Step 9 Click OK. The row on the Pluggable Ports pane turns light blue until the actual SFP is installed and then the row turns white. Stop. You have completed this procedure. NTP-E150 Change the Optical Line Rate Purpose This procedure changes PPM port rates for the ASAP card. Perform this procedure if you want to change the port rate on a multi-rate SFP that is already provisioned. Tools/Equipment None Prerequisite Pr
ページ5に含まれる内容の要旨
Chapter 11 Change Card Settings NTP-E149 Delete Pluggable Port Modules NTP-E149 Delete Pluggable Port Modules Purpose This procedure deletes PPM provisioning for SFPs on the ASAP card. Tools/Equipment None Prerequisite Procedures NTP-E157 Provision a Multirate PPM, page 11-2 Required/As Needed As needed Onsite/Remote Onsite or remote Security Level Provisioning or higher Step 1 Complete the “DLP-E26 Log into CTC” task on page 16-39 to log into an ONS 15600 on the network. Step 2 Click the
ページ6に含まれる内容の要旨
Chapter 11 Change Card Settings NTP-E66 Modify Line and Status Thresholds for Optical Ports Note If you need to remove the SFP, see the “DLP-E216 Remove an SFP” procedure on page 18-15. If you need to remove the 4PIO, see the “DLP-E217 Remove a 4PIO Module” procedure on page 18-16.” Stop. You have completed this procedure. NTP-E66 Modify Line and Status Thresholds for Optical Ports Purpose This procedure changes line settings (line type, coding, and length), line status (in service or ou
ページ7に含まれる内容の要旨
Chapter 11 Change Card Settings NTP-E66 Modify Line and Status Thresholds for Optical Ports Table 11-2 OC-N Card Line Settings (continued) Heading Description Options SD BER Sets the signal degrade bit error rate 1E-5 1E-6 1E-7 (default) 1E-8 1E-9 Provides Sync Indicates that the port has been Read-only provisioned as a network element timing Yes (checked) reference on another node (ONS 15600, No (unchecked) ONS 15454, or ONS 15327) Send Do Not When checked, sends a DUS (do
ページ8に含まれる内容の要旨
Chapter 11 Change Card Settings NTP-E66 Modify Line and Status Thresholds for Optical Ports Table 11-2 OC-N Card Line Settings (continued) Heading Description Options Service State Identifies the autonomously generated IS-NR—(In-Service and Normal) state that gives the overall condition of The port is fully operational and the port. Service states appear in the performing as provisioned. format: Primary State-Primary State OOS-AU,AINS—(Out-Of-Service Qualifier, Secondary State. and
ページ9に含まれる内容の要旨
Chapter 11 Change Card Settings NTP-E66 Modify Line and Status Thresholds for Optical Ports Step 7 Click the Thresholds subtab. The default selection is Near End, 15 Min, and Line (Figure 11-1). Figure 11-1 Provisioning Thresholds for the OC-48 Card Step 8 As needed, complete the following: a. Click Line, Section, Path, or Physical to provision the line, section, path, and physical options in Table 11-3 for each OC-N port. b. Change the selection to Near End/Far End, 15 Min/1Day as nece
ページ10に含まれる内容の要旨
Chapter 11 Change Card Settings NTP-E66 Modify Line and Status Thresholds for Optical Ports Table 11-3 OC-N Threshold Options (Line, Section, and Path) Heading Description Options Port Port number 1 – 16 for an OC-48 card, 1 – 4 for an OC-192 card CV Coding violations Numeric. Defaults (15 min/1 day): Line 21260/212600 (OC-48 Near and Far End) 85040/850400 (OC-192 Near and Far End) Section 10000/100000 (Near End); 0/0 (Far End) 10000/500 (OC-192 Near and Far End) Path 15/12
ページ11に含まれる内容の要旨
Chapter 11 Change Card Settings NTP-E66 Modify Line and Status Thresholds for Optical Ports Table 11-3 OC-N Threshold Options (Line, Section, and Path) (continued) Heading Description Options FC Failure count Numeric. Defaults (15 min/1 day): Line 10/40 (OC-48/OC-192 Near and Far End) Path 10/10 (OC-48/OC-192 Near and Far End) UAS Unavailable seconds Numeric. Defaults (15 min/1 day): Line 3/10 (OC-48/OC-192 Near and Far End) Path 10/10 (Near and Far End) PSC Protection Switching
ページ12に含まれる内容の要旨
Chapter 11 Change Card Settings NTP-E105 Change an Optical Port to SDH Table 11-4 OC-N Threshold Options (Physical) Heading Description Options Port Port number 1 – 16 for an OC-48 card, 1 – 4 for an OC-192 card LBC-HIGH Laser bias current–maximum Default (15 min/1 day): 150 percent LBC-LOW Laser bias current–minimum Default (15 min/1 day): 50 percent OPT-HIGH Optical power transmitted–maximum Default (15 min/1 day): 120 percent OPT-LOW Optical power transmitted–minimum Default (15 min/1
ページ13に含まれる内容の要旨
Chapter 11 Change Card Settings NTP-E125 Change Card Service State Step 6 You can repeat Steps 4 and 5 for any other ports on that card. Stop. You have completed this procedure. NTP-E125 Change Card Service State Purpose This procedure changes card service state. Tools/Equipment None Prerequisite Procedures Chapter 2, “Install Cards and Fiber-Optic Cable” Required/As Needed As needed Onsite/Remote Onsite or remote Security Level Provisioning or higher Step 1 Complete the “DLP-E26 Log into
ページ14に含まれる内容の要旨
Chapter 11 Change Card Settings NTP-E125 Change Card Service State Table 11-5 Cisco ONS 15600 Card State Transitions (continued) Admin State Original Service State Next Service State OOS,MT OOS-AU,AINS & UEQ OOS-AUMA,MT & UEQ (Out-of-Service and Autonomous,Auto (Out-of-Service and Autonomous In-Service and Unequipped) Management,Maintenance and Unequipped) OOS,MT OOS-AU,AINS & MEA OOS-AUMA,MEA & MT (Out-of-Service and Autonomous,Auto (Out-of-Service and Autonomous In-Service and Mismatch
