ページ1に含まれる内容の要旨
Enterprise Networking Solution
Installation Guide
Gigabit Unmanaged Switch
TL-SG1048
TL-SG1024/TL-SG1024D
TL-SG1016/TL-SG1016D
TL-SG1008/TL-SG1008PE
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2013 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. ht
ページ4に含まれる内容の要旨
Related Document This Installation Guide is also available in PDF on our website. To obtain the latest documentation and product information, please visit the official website: http://www.tp-link.com About this Installation Guide This Installation Guide describes the hardware characteristics, installation methods and the points that should be attended to during the installation. This Installation Guide is structured as follows: Chapter 1 Introduction. This chapter describes the external c
ページ5に含まれる内容の要旨
Contents Chapter 1 Introduction ——————————— 01 1.1 Product Overview ...................................................................01 1.2 Features ......................................................................................01 1.3 Appearance ...............................................................................02 Chapter 2 Installation ———————————— 08 2.1 Package Contents ...................................................................08 2.2 Safety Precautions ..........
ページ6に含まれる内容の要旨
Gigabit Unmanaged Switch ChaCter C Introduction C1C Product Overview The Gigabit Unmanaged Switch provides you with a high-performance, low-cost, easy- to-use, seamless and standard upgrade to boost your old network to 1000Mbps. By increasing the speed of your network server and backbone connections, the Gigabit Unmanaged Switch makes Gigabit a reality. Power users in the home, office, workgroup, or creative production environment can now move large, bandwidth- intensive files faster. Graphics,
ページ7に含まれる内容の要旨
Gigabit Unmanaged Switch • Supports IEEE802.3x flow control for full-duplex mode and backpressure for half- duplex transfer mode • Non-blocking switching architecture that forwards and filters packets at full wire- speed for maximum throughput • Supports MAC address auto-learning and auto-aging • Desktop and rack-mountable steel case • Internal power supply For TL-SG1008PE: • Complies with IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3x, IEEE802.3af and IEEE802.3at standards • 8 10/100/1000Mbps A
ページ8に含まれる内容の要旨
Gigabit Unmanaged Switch 10/100/1000Mbps RJ45 Port Designed to connect to the device with a bandwidth of 10Mbps, 100Mbps or 1000Mbps. Each has a corresponding Link/Act LED. The front panel of TL-SG1024 is shown as the following figure. LEDs 10/100/1000Mbps RJ45 Port Figure 1-2 Front Panel of TL-SG1024 The front panel of TL-SG1016 is shown as the following figure. LEDs 10/100/1000Mbps RJ45 Port Figure 1-3 Front Panel of TL-SG1016 The front panel of TL-SG1024D is shown as the following figure. LE
ページ9に含まれる内容の要旨
Gigabit Unmanaged Switch The front panel of TL-SG1008 is shown as the following figure. LEDs 10/100/1000Mbps RJ45 Port Figure 1-6 Front Panel of TL-SG1008 LEDs LED Status Indication On The switch is powered on. Power Off The switch is powered off or power supply is abnormal. There is a device linked to the corresponding port but no On activity. Link/Act Flashing The corresponding port is transmitting or receiving data. Off There is no device linked to the corresponding port. On A 1000Mbps devic
ページ10に含まれる内容の要旨
Gigabit Unmanaged Switch LED Status Indication The power of all the connected PoE ports is between On (red1 118W and 124W. No power may be supplied if additional PDs are connected. PoE MAX Flashing (red1 The power of all the connected PoE ports is >=124W. The power of all the connected PoE ports is <118W, or Off there is no PD connected to the corresponding port. There is a 1000Mbps device connected to the On (green1 corresponding port. 1000Mbps There is a 10/100Mbps device connected to the
ページ11に含まれる内容の要旨
Gigabit Unmanaged Switch Rear Panel The rear panel of TL-SG1048 is shown as the following figure. Power Socket Grounding Terminal Figure 1-8 Rear Panel of TL-SG1048 The rear panel of TL-SG1024/TL-SG1016 is shown as the following figure. Power Socket Grounding Terminal Figure 1-F Rear Panel of TL-SG1024/TL-SG1016 The rear panel of TL-SG1024D/TL-SG1016D is shown as the following figure. Grounding Terminal Power Socket Figure 1-10 Rear Panel of TL-SG1024D/TL-SG1016D The rear panel of TL-SG1008 is s
ページ12に含まれる内容の要旨
Gigabit Unmanaged Switch Power Socket Connect the female connector of the power cord here, and the male connector to the AC (Alternating Current1 power outlet. Please make sure the voltage of the power supply meets the requirement of the input voltage. Grounding Terminal The Switch already comes with lightning protection mechanism. You can also ground the Switch through the PE (Protecting Earth1 cable of AC cord or with Ground Cable. For detailed information, please refer to Chapter 3 Light
ページ13に含まれる内容の要旨
Gigabit Unmanaged Switch ChaCter 1 Installation 11C Package Contents Make sure that the package contains the following items. If any of the listed items is damaged or missing, please contact your distributor. One Switch One Power Cord This Installation Guide Two mounting brackets and the fittings 111 Safety Precautions To avoid any device damage and bodily injury caused by improper use, please observe the following rules. ■ Safety Precautions ■ Keep the power off during the installation. ■
ページ14に含まれる内容の要旨
Gigabit Unmanaged Switch ■ Site Requirements Temperature/Humidity 40℃ 0℃ Please keep a proper temperature and humidity in the equipment room. Too high/low humidity may lead to bad insulation, electricity leakage, mechanical property changes and corrosions. Too high temperature may accelerate aging of the insulation materials and can thus significantly shorten the service life of the device. For normal temperature and humidity of the device, please check the following table. Environment Temp
ページ15に含まれる内容の要旨
Gigabit Unmanaged Switch Lightening Protection Extremely high voltage currents can be produced instantly when lightning occurs and the air in the electric discharge path can be instantly heated up to 20,000℃. As this instant current is strong enough to damage electronic devices, more effective lightning protection measures should be taken. ■ Ensure the rack and device are well earthed. ■ Make sure the power socket has a good contact with the ground. ■ Keep a reasonable cabling system and a
ページ16に含まれる内容の要旨
Gigabit Unmanaged Switch 112 Product Installation ■ Desktop Installation To install the device on the desktop, please follow the steps: 1. Set the device on a flat surface strong enough to support the entire weight of the device with all fittings. 2. Remove the adhesive backing papers from the rubber feet. 3. Turnover the device and attach the supplied rubber feet to the recessed areas on the bottom at each corner of the device. Feet Bottom of the Device Notch Figure 2-1 Desktop Installation
ページ17に含まれる内容の要旨
Gigabit Unmanaged Switch Rack Figure 2-3 Rack Installation Caution: ■ Please set 5~10cm gaps around the device for air circulation. ■ Please avoid any heavy thing placed on the device. ■ Please mount devices in sequence from the bottom to top of the rack and ensure a certain clearance between devices for the purpose of heat dissipation. Installation 12
ページ18に含まれる内容の要旨
Gigabit Unmanaged Switch ChaCter 1 Lightning Protection 11C Cabling Reasonably In the actual network environment, you may need cable outdoors and indoors, and the requirements for cabling outdoors and indoors are different. A reasonable cabling system can decrease the damage of induced lightning to devices. Note: It's not recommended using Ethernet cables outdoors. When cabling outdoors, please use a signal lightning arrester. ■ Requirements for Cabling Outdoors ■ Aerial cabling without saf
ページ19に含まれる内容の要旨
Gigabit Unmanaged Switch ■ Requirements for Cabling Indoors When cabling indoors, keep a certain distance away from the devices that may cause high-frequency interferences, such as down-conductor cable, powerline, power transformer and electromotor. ■ The main cable should be paved in the metal raceway of the access shaft. When cabling, keep the loop area formed by the cable itself as small as possible. ■ Requirements for the distance between Ethernet cable and other pipelines are shown i
ページ20に含まれる内容の要旨
Gigabit Unmanaged Switch Min Parallel Cable Pave Way Length (mm1 Parallel cabling 300 2~5kVA One is in the grounded metal raceway or metal pipe 150 powerline The both are in the grounded metal raceway or metal 80 pipe Parallel cabling 600 >5kVA One is in the grounded metal raceway or metal pipe 300 powerline The both are in the grounded metal raceway or metal 150 pipe Device Min Distance (m1 Switch case 1.00 Transformer room 2.00 Elevator tower 2.00 Air-conditioner room 2.00 111 Connect to Gr
