Summary of the content on the page No. 1
6022SH
Owner’s Manual
532180311 10.15.01 BY
Printed in U.S.A.
Summary of the content on the page No. 2
SAFETY RULES Safe Operation Practices for Walk-Behind Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. DO NOT: I. GENERAL OPERATION Do not trim near drop-offs, ditches or embankments. The • Read, understand, and follow all instructions on the machine operator could lose footing or balance. and in the manual(s) before starting. Be thoroughly famili
Summary of the content on the page No. 3
WARNING: Engine exhaust, some of its Look for this symbol to point out impor- constituents, and certain vehicle com- tant safety precautions. It means ponents contain or emit chemicals known CAUTION!!! BECOME ALERT!!! YOUR to the State of California to cause cancer SAFETY IS INVOLVED. and birth defects or other reproductive harm. CAUTION: Always disconnect spark WARNING: Battery posts, terminals and plug wire and place wire where it cannot related accessories contain lead and contact spark p
Summary of the content on the page No. 4
4 WARRANTY STATEMENT SECTION 4: EXCEPTIONS AND LIMITATIONS SECTION 1: LIMITED WARRANTY This warranty shall be inapplicable to defects resulting from the following: Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original purchaser to be free from defects in material and workmanship from the date of purchase for the (1) Accident, abuse, misuse, negligence and neglect, including stale fuel, dirt, abrasives, moisture, rust, “Warranty Period” of the product as set
Summary of the content on the page No. 5
ASSEMBLY Read these instructions and this manual in its entirety before HOW TO SET UP YOUR LAWN MOWER you attempt to assemble or operate your new lawn mower. TO UNFOLD HANDLE (See Fig. 1) IMPORTANT: THIS LAWN MOWER IS SHIPPED WITHOUT IMPORTANT: UNFOLD HANDLE CAREFULLY SO AS OIL OR GASOLINE IN THE ENGINE. NOT TO PINCH OR DAMAGE CONTROL CABLES. Your new lawn mower has been assembled at the factory 1. Raise handles until lower handle section locks into place with the exception of those parts left
Summary of the content on the page No. 6
OPERATION KNOW YOUR LAWN MOWER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR LAWN MOWER. Compare the illustrations with your lawn mower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your lawn mower or in literature supplied with the product. Learn and understand their meaning. OPERATOR PRESENCE CONTROL BAR THROTTLE CONTROL ENGINE ZONE CONTROL CABLE HANDLE KNOB STARTER HANDLE
Summary of the content on the page No. 7
OPERATION The operation of any lawn mower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your lawn mower or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses. HOW TO USE YOUR LAWN MOWER PLATE TAB ENGINE SPEED (See Fig. 2) The engine speed is controlled by a throttle located on the side of the upper handle. FAST position is
Summary of the content on the page No. 8
OPERATION BEFORE STARTING ENGINE ENGINE ADD OIL (See Fig. 5) OIL CAP Your lawnmower is shipped without oil in the engine. Engine holds 20 ounces of oil. For type and grade of oil to use, see “ENGINE” in the Maintenance section of this manual. 1. Be sure lawnmower is level and area around oil fill is clean. 2. Remove engine oil cap and fill to the full line on the dipstick. Pour oil slowly. Do not over fill. NOTE: Allow oil to settle down into engine for accurate GASOLINE reading. To read pr
Summary of the content on the page No. 9
OPERATION MULCHING MOWING TIPS MOWING TIPS IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER Under certain conditions, such as very tall grass, it may HOUSING FREE OF BUILT-UP GRASS AND TRASH. SEE be necessary to raise the height of cut to reduce pushing “CLEANING” IN THE MAINTENANCE SECTION OF THIS effort and to keep from overloading the engine and MANUAL. leaving clumps of grass clippings. It may also be The special mulching blade will recut the grass clippings necessary to reduce ground speed
Summary of the content on the page No. 10
MAINTENANCE MAINTENANCE SCHEDULE FILL IN DATES AS YOU COMPLETE SERVICE DATES REGULAR SERVICE Check for Loose Fasteners Clean/Inspect Grass Catcher (If Equipped) Clean Lawn Mower M Clean Under Drive Cover O (Power-Propelled Mowers) W Check drive belt/pulleys E (Power-Propelled Mowers) R Check/Sharpen/Replace Blade 3 Lubrication Chart Clean Battery/Recharge (Electric Start Mowers) 4 Check Engine Oil Level E Change Engine Oil 1,2 N Clean Air Filter 2 2 G Inspect Muffler I Clean or Replace Spark Pl
Summary of the content on the page No. 11
MAINTENANCE 4. Install the blade bolt with the lock washer and hardened LAWN MOWER washer into blade adapter and crankshaft. Always observe safety rules when performing any mainte- 5. Use block of wood between blade and lawn mower nance. housing and tighten the blade bolt, turning clockwise. The recommended tightening torque is 35-40 ft. lbs. TIRES IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED. Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber. TO SHARPEN
Summary of the content on the page No. 12
MAINTENANCE GRASS CATCHER (If purchased as an accesssory) The grass catcher may be hosed with water, but must be dry when used. Check your grass catcher often for damage or deterio- ration. Through normal use it will wear. If catcher needs replacing, replace only with a manufacturer approved replacement catcher. Give the lawn mower model number when ordering. ENGINE Read the Maintenance section of your engine manual. LUBRICATION Use only high quality detergent oil rated with API service C
Summary of the content on the page No. 13
SERVICE AND ADJUSTMENTS CAUTION: BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: 1. Release control bar and stop engine. 2. Make sure the blade and all moving parts have completely stopped. 3. Disconnect spark plug wire from spark plug and place where it cannot come in contact with plug. LAWN MOWER TO ADJUST CUTTING HEIGHT See “TO ADJUST CUTTING HEIGHT” in the Operation section of this manual. REAR DEFLECTOR The rear deflector, attached between the rear wheels of your mower, is provided to minimi
Summary of the content on the page No. 14
STORAGE Immediately prepare your lawn mower for storage at the end of the season or if it will not be used for 30 days or more. OPERATOR PRESENCE CONTROL BAR LAWN MOWER UPPER HANDLE When lawn mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area. LOWER HANDLE 1. Clean entire lawn mower (See “CLEANING” in the Maintenance section of this manual). 2. Lubricate as shown in the Maintenance section of this
Summary of the content on the page No. 15
IMPORTANT: NEVER COVER MOWER WHILE ENGINE OTHER AND EXHAUST AREAS ARE STILL WARM. Do not store gasoline from one season to another. CAUTION: Never store the lawn mower Replace your gasoline can if your can starts to rust. with gasoline in the tank inside a build- Rust and/or dirt in your gasoline will cause problems. ing where fumes may reach an open If possible, store your unit indoors and cover it to give flame or spark. Allow the engine to cool protection from dust and dirt. before st
Summary of the content on the page No. 16
16 REPAIR PARTS ROTARY LAWN MOWER - - MODEL NUMBER 6022SH (6022SHB)
Summary of the content on the page No. 17
17 REPAIR PARTS ROTARY LAWN MOWER - - MODEL NUMBER 6022SH (6022SHB) KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 532 06 36-01 Locknut 1/4-20 47 532 75 05-50 Wheel Assembly (Front) 2 532 17 65-63 Control Bar 48 532 05 71-43 Washer 3 532 17 95-85 Rope Guide 50 532 07 74-00 Hubcap 4 532 17 36-93 Upper Handle (with Foam Grip) 51 874 76 05-14 Hex Head Bolt 5/16-18x 5 532 17 42-91 Lower Handle 52 532 15 04-06 Hex Head Thread Rolling Screw 3/8-16 x 1 6 532 06 36-01 Locknut 1/4-20 55
Summary of the content on the page No. 18
NOTES 18
