Summary of the content on the page No. 1
STIGA PARK
4 WD
107 M
107 M HD
121 M
125 Combi Pro
B
INSTRUCTIONS FOR USE
£
»HC“P”K÷»fl œOÀ‹«Œ¬¿“EÀfl®
8211-0543-01
Summary of the content on the page No. 2
2 125 Combi Pro 1 125 Combi Pro 3 4 125 Combi Pro 121 M 107 M HD 125 Combi Pro B C 107 M HD B A 121 M 5 125 Combi Pro 6 125 Combi Pro Torx T30 E F Torx T30 7 121 M 8 121 M G H I 10 mm 10 mm
Summary of the content on the page No. 3
10 107 9 107 13 mm 13 mm 10 mm 12 107 M 11 107 M B D B A J K L 14 13 107 M HD 15 16 M
Summary of the content on the page No. 4
18 17 1/3 5 mm 20 19 21 125 Combi Pro 22 107 M HD M N 24 Nm P 24 Nm Q 9,8 Nm 23 24 24 Nm
Summary of the content on the page No. 5
EN ENGLISH 1 GENERAL 2 DESCRIPTION This symbol indicates WARNING. Seri- 2.1 General ous personal injury and/or damage to The cutting deck is intended for use on Stiga’s 4- property may result if the instructions wheel drive Park machines. are not followed carefully. The cutting deck is supplied in one of the follow- You must read these instructions for use ing versions: and the machine’s safety instructions • With manual adjustment of cutting height. carefully. • With electrical adjustment
Summary of the content on the page No. 6
EN ENGLISH 2.3.3 Rear mounting 2.5.3 Rear mounting The cutting deck’s rear section is secured with the The cutting deck’s rear section is secured with the pins in fig. 13. pins (7:I). 2.3.4 Mounting in implement lifter 2.5.4 Mounting in implement lifter The deck is mounted in the implement lifter with a The deck is mounted in the implement lifter with a chain and snap hooks. chain and snap hooks. One snap hook is intended for the working position One snap hook is intended for the working posi
Summary of the content on the page No. 7
EN ENGLISH 3. Install the deck arms in the cutting deck’s front 3.2 Installation of 107 M HD, 121 M corners. After tightening, it should be possible 1. Place the cutting deck in position in front of the to move the rear section of the cutting deck free- machine. ly up and down. 2. Install the following components on both wheel 4. Suspend the cutting deck in the implement lift- axles: er. See fig. 14. • Washer (3:B). • Deck mount (3:C). 3.3.1 Belt, 107 M • Washer (3:B). The cutting deck’s rea
Summary of the content on the page No. 8
EN ENGLISH 5. Undo the screws (7:H and 12:K) so that the • Mulching: composting and spreading. deck rests against the plank and the spacer. • Rear ejection: ejects the grass in a line behind Check that the deck does not lean sideways in the deck. relation to the machine. The deck is set for mulching on delivery. In order 6. Tighten the screws (7:H and 12:K) to 22 Nm. to eject the grass in a line behind the deck, the plug 7. Place the deck in transport position and remove in fig. 6 must be
Summary of the content on the page No. 9
EN ENGLISH 5.3 Service position 5.6 Replacing blades 1. Activate the parking brake. Wear protective gloves when changing 2. Set the implement lifter in transport position. blade(s) to avoid cutting yourself. 3. If the deck has electrical cutting height adjust- Check that the blades are always sharp. ment, disconnect the cable from the machine. This produces the best cutting results. See fig. 15. Always check the blade(s) after a collision. If the 4. 125 Combi Pro, 107 M HD, 107 M: blade syst
Summary of the content on the page No. 10
EN ENGLISH 6 SPARE PARTS 7 DESIGN REGISTRATION STIGA genuine spare parts and accessories are de- This product or parts thereof is covered by the fol- signed specifically for STIGA machines. Please lowing design registration: note that ‘non-genuine’ spare parts and accessories Sweden: 66 166 have not been checked or approved by STIGA: Germany: 499 11 740.9 The use of such parts and accessories France: 577 251-253, 577 439-443 can affect the function and safety of the USA: 435 564 machine. STIG
Summary of the content on the page No. 11
www.stiga.com GGP Sweden AB · Box 1006 · SE-573 28 TRANÅS
