Summary of the content on the page No. 1
User Guide
InRoom SC 50 Hz
ACPSC3000
TEMP MODE
InRoom SC
Summary of the content on the page No. 2
Summary of the content on the page No. 3
American Power Conversion Legal Disclaimer The information presented in this manual is not warranted by the American Power Conversion Corpora- tion to be authoritative, error free, or complete. This publication is not meant to be a substitute for a detailed operational and site specific development plan. Therefore, American Power Conversion Corpo- ration assumes no liability for damages, violations of codes, improper installation, system failures, or any other problems that could arise based o
Summary of the content on the page No. 4
Summary of the content on the page No. 5
Contents General Information........................................................ 1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Save these instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 About the InRoom SC Portable Cooling Unit . . . . . . . . . . . . . . . . . . 1 Performance Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Safety symbols that may be used in thi
Summary of the content on the page No. 6
Display Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Display Screen Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Function Button and Indicator Light Operation . . . . . . . . . . . . . . . 15 Remote Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Maintenance................................................................... 19 Clean the exterior . . . . . . . . . . .
Summary of the content on the page No. 7
General Information Overview Save these instructions This manual contains important instructions that must be followed during the installation of this equipment. About the InRoom SC Portable Cooling Unit InRoom SC cooling units are portable, compact air conditioners designed for spot-cooling, emergency- cooling, and after-hours cooling of server closets and data centers. If the building’s cooling system has night and weekend thermostat setbacks, is shut down during the off- season or maintenan
Summary of the content on the page No. 8
Safety symbols that may be used in this manual Electrical Hazard: Indicates an electrical hazard which, if not avoided, could result in injury or death. Danger: Indicates a hazard which, if not avoided, could result in severe personal injury or substantial damage to product or other property. Warning: Indicates a hazard which, if not avoided, could result in personal injury or damage to product or other property. Caution: Indicates a potential hazard which, if not avoided, could result in
Summary of the content on the page No. 9
Safety Electrical Hazard: Connect the equipment to a 220-240V, 50Hz, three prong grounded outlet (two poles plus a ground). The use of a time-delay fuse or time-delay circuit breaker is recommended. Connection to any other power source may result in a shock hazard or damage to the cooling unit. Do not cut or remove the ground from the power cord plug. Use the cooling unit with the supplied power cord only. Do not use an extension cord with this cooling unit. If the plug gets hot, call a quali
Summary of the content on the page No. 10
TEMP MODE InRoom SC Storing the Cooling Unit If the cooling unit will not be installed immediately, replace the packaging to protect from damage and dust. Store the cooling unit indoors in a climate controlled, dry place. Caution: Leaving the cooling unit uncovered and exposed to the elements can cause damage and voids the factory warranty. Cooling Unit Packaging Recycle the packaging material when possible. Do not discard packaging material until the cooling unit has been inspected. Rem
Summary of the content on the page No. 11
Inspecting the Cooling Unit Your cooling unit has been tested and inspected before shipment. To ensure that the cooling unit has not been damaged during transit, carefully inspect the cooling unit immediately upon receipt. Caution: Do not tip or place the unit on its side. Verify that all parts ordered were received as specified. See “Inventory” on page 6. Filing a claim If damage is identified on receipt of the cooling unit, note the damage on the bill of lading and file a damage claim wi
Summary of the content on the page No. 12
MODE TIMER Tools Required Phillips head screwdriver Inventory Item Description Item Description Cooling unit Wrench (for casters) 1 7 Remote control Drain hose 2 8 Ceiling adapter Phillips head screw, ST4.2 x 9.5 (for hose clip) 3 9 Exhaust cap Exhaust hose Hose Clip 4 : Phillips head screw ST4.2 x 9.5 (2) Hose Clamp (2) 5 ; Exhaust hose Rubber drain plug 6 < 6 InRoom SC 50 Hz User Guide SEND DRY Hr. + °C - °C Min ON/OFF SLEEP MODE TEMP InRoom SC FAN na3368a
Summary of the content on the page No. 13
E DE T MP MO InRoom SC MODE TIMER SEND DRY Hr. + °F i - °F M n / ON OFF SL EEP FAN Component Identification ACPSC3000 Item Description Control panel 1 Air louver 2 Remote control sensor 3 Remote control / storage 4 Air filter / upper air intake (evaporator) 5 Air outlet (heat exchanger) 6 Power cord 7 Lower air intake (condenser) 8 Water outlet drain 9 Caster : Lower air intake (condenser) ; Handle < InRoom SC 50 Hz User Guide 7 MP MO E n oom S TE D I R C na3365a
Summary of the content on the page No. 14
> 500 (20) Installation Location Requirements When deciding where to locate the cooling unit, consider cooling needs, air flow, and the location of the electrical outlet. The cooling unit can be no more than 2.4 m (8 ft) from the electrical outlet. Cooling needs. Position the cooling unit as close as possible to the main heat source that requires cooling. Air flow. Position the cooling unit at least 500 mm (20 in) away from a wall or other equipment on any side to avoid impeding air f
Summary of the content on the page No. 15
TEMP MODE InRoom SC Exhaust Duct Assembly Dry Mode. Exhaust air must be allowed to return to the room in order for dehumidification to take place. Do not connect the exhaust hose to vent it outside the room. Continuous drainage for the condensate drain pan must be provided or it will fill up and the unit will automatically shut down until it is emptied. Cool Mode. Exhaust air must vent outside the room when using the cool mode. Note: Leave the door to the room slightly ajar to equalize pre
Summary of the content on the page No. 16
Installation. Exhaust air can be vented to the outside through the ceiling. The cooling unit should be positioned a minimum of 500 mm (20 in) from any wall; either at the back or on the sides. In a dropped ceiling, the ceiling adapter can be installed in place of one of the ceiling tiles. 1. Position the end of the exhaust hose so the small tabs line up with the holes in the ceiling adapter. 1 Insert the exhaust hose into the ceiling adapter and 2 turn the exhaust hose counterclockwise sli
Summary of the content on the page No. 17
Window Installation. Exhaust air can be vented to the outside through a window. The ceiling adapter can be placed into a window opening and the window can be pulled down to hold the panel in place. Install the exhaust hose to the adapter panel as done on the previous page. Wall Installation. Exhaust air can be vented to the outside through a wall. Adhere to local restrictions and regulations. The cooling unit should be positioned a minimum of 500 mm (20 in) from any wall; either at the b
Summary of the content on the page No. 18
TEMP MODE InRoom SC Drain Kit Installation The InRoom SC utilizes evaporative technology, which eliminates the need for a condensate tank. To manage any excess condensation, a drain pan is located in the bottom of the unit. When the drain pan is full, a light will flash on the display and an alarm will sound to alert you. The cooling unit will automatically shut down. To avoid a shut down, install the drain kit and route the hose to a drain. See “Inventory” on page 6 for a description of the
Summary of the content on the page No. 19
Operation Control Panel TEMP MODE InRoom SC Function Button Locations Item Function Description Temp Up and down arrow buttons adjust the thermostat. 1 Display interface LCD user interface displays instructions and functions. 2 Mode selection Three mode control settings: Cool, Dehumidify, and Fan. 3 The settings are adjusted by pressing the Mode Control Button. Fan speed control Press the Fan Speed Control button to move through the three settings: 4 Low, Medium and High. Power control Tur
Summary of the content on the page No. 20
Display Interface FAN COOL DRY SLEEP °C ON LOW MED HIGH OFF SET TEMP AUTO SET TIME Display Screen Information Item Function Description Sleep mode indicator Sleep mode is an undercooling mode that is used during times of non- 1 peak heat. Sleep mode is activated by setting the timer. The set temperature will automatically increase at intervals until the timer turns off the Sleep mode. Cool mode indicator Cool mode cools the room. Temperature and fan speed are set by the user. 2 Fan mode ind
