Our goal is to provide you with a quick access to the content of the user manual for JBL gto755.6 II. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with JBL gto755.6 II.
If looking through the JBL gto755.6 II user manual directly on this website is not convenient for you, there are two possible solutions:
Explore the detailed user manual for JBL remarkable creation, Model gto755.6 II. Gain valuable insights and instructions to maximize your device's capabilities and optimize your user experience. Uncover the full potential of your JBL gto755.6 II device through this comprehensive user manual, offering step-by-step guidance and expert tips for effortless operation and enjoyment.
Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual JBL gto755.6 II but the selected pages only. paper.
Below you will find previews of the content of the user manuals presented on the following pages to JBL gto755.6 II. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.
for purchasing a JBL Grand Touring Series II amplifier.
In order that we may better serve you should you
require warranty service for your new amplifier, please
retain your original purchase receipt and return the
enclosed warranty registration card.
INSTALLATION WARNING: Playing loud music in an • Before drilling or cutting holes, use a POWER CONNECTIONS Speaker Connections automobile can hinder your ability to hear utility knife to remove unwanted fabric The GTO amplifiers are capable of Refer to the application guides on the traffic and permanently damage your or vinyl to keep material from snagging delivering extremely high power levels, pages that follow. Speaker connections hearing. We recommend lis
APPLICATIONS – GTO301.1 II, GTO601.1 II AND GTO1201.1 II The GTO subwoofer amplifiers are single-channel amplifiers. There are two sets of terminals to make it easy to connect multiple woofers. Either set of (+/–) terminals may be used when connecting woofers. To the right are two application diagrams to help plan your subwoofer GTO Amplifier GTO Amplifier (partial end panel) (partial end panel) system installation. Figures 2 and 3 show how to configure the GTO +
APPLICATIONS – GTO75.4 II The GTO75.4 II can be set up for stereo – 4-channel, 3-channel or bridged + 2-channel operation, as shown in Figures 6 through 8. NOTE: For simplicity, Figures 6 through 8 do not show power, remote and input connections. NOTE: Minimum speaker impedance for stereo operation is 2 ohms. GTO75.4 II Minimum speaker impedance for (partial end panel) + bridged operation is 4 ohms. – Figure 6. GTO75.4 II amplifier in 4-channel (stereo) operation to drive f
APPLICATIONS – GTO755.6 II Rear Front The GTO755.6 II can be configured for Subwoofer Right Right 6-channel, 5-channel or 3-channel – – + operation, as shown in Figures 9 + through 11. Input Mode Switch: • Use INT (internal mode) to send a signal from the front and rear inputs to the subwoofer. • Use EXT (external mode) when sending a dedicated signal to the GTO755.6 II subwoofer inputs; e.g., if your source (partial end panel) unit has a subwoofer output. – – + + N
INSTALLATION AND SETUP SETTING THE SETTING INPUT REMOTE LEVEL CONTROL INSTALLING NEON TUBES CROSSOVER(S) SENSITIVITY The GTO755.6 II and all three GTO (OPTIONAL) Determine your system plans and set the 1. Initially turn the INPUT LEVEL control(s) subwoofer amplifiers have inputs for 1. Using a Phillips screwdriver, remove all crossover mode switch accordingly. If to minimum (counter clockwise). an optional remote level control (RLC). screws on the amplifier’s output/p
INSTALLATION AND SETUP To Neon Power Supply To Neon Power Supply Figure 13. Installing neon tubes in a JBL GTO amplifier. TROUBLESHOOTING SYMPTOM LIKELY CAUSE SOLUTION SYMPTOM LIKELY CAUSE SOLUTION No audio No voltage at BATT+ Check voltages at No audio Voltage more than 16V Check vehicle (POWER LED or REM terminals, amplifier terminals (PROTECT or less than 8.5V on charging system for is off) or bad or no ground with VOM LED is on) BATT+ connection defective voltage connection r
SPECIFICATIONS GTO301.1II GTO601.1II GTO1201.1II • 204W RMS x 1 channel at 4 ohms and ≤1% THD + N • 424W RMS x 1 channel at 4 ohms and ≤1% THD + N • 787W RMS x 1 channel at 4 ohms and ≤1% THD + N • Signal-to-noise ratio: 77dBA (reference 1W into 4 ohms) • Signal-to-noise ratio: 72dBA (reference 1W into 4 ohms) • Signal-to-noise ratio: 70dBA (reference 1W into 4 ohms) • 294W RMS x 1 channel at 2 ohms, 14.4V supply and • 580W RMS x 1 channel at 2 ohms, 14.4V supply and • 1114W RM
|1||JBL CS60.4 User manual||Car Amplifier||459|
|2||JBL GTO3501 User manual||Car Amplifier||94|
|3||JBL GT5A3011OM User manual||Car Amplifier||10|
|4||JBL GTO601.1 User manual||Car Amplifier||18|
|5||JBL CS60.2 User manual||Car Amplifier||209|
|6||JBL GTO301.1 User manual||Car Amplifier||37|
|7||JBL GTO755.6 User manual||Car Amplifier||104|
|8||JBL GTO14001 User manual||Car Amplifier||291|
|9||JBL A6000GTi User manual||Car Amplifier||47|
|10||JBL GTO5355 User manual||Car Amplifier||379|
|11||JBL CS300.1 User manual||Car Amplifier||67|
|12||JBL GTO75.2 User manual||Car Amplifier||105|
|13||JBL GTH400-20107 User manual||Car Amplifier||183|
|14||JBL CS Series User manual||Car Amplifier||64|
|15||JBL GTO1201.1 User manual||Car Amplifier||26|
|16||Sony XM-1600GSD User manual||Car Amplifier||34|
|17||Adcom GFA-4304 User manual||Car Amplifier||3|
|18||Sony XM-2000R User manual||Car Amplifier||21|
|19||Sony XDP-210EQ User manual||Car Amplifier||38|
|20||Samsung T500-1BD User manual||Car Amplifier||0|