Streszczenie treści zawartej na stronie nr. 1
Etherlink IIIB ISA Network
Interface Card (10BT)
3C509B-TP
Installation Guide
Streszczenie treści zawartej na stronie nr. 2
Notice The information contained in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. Hewlett-Packard assumes no responsibility
Streszczenie treści zawartej na stronie nr. 3
1 Connecting to a Netware 3.12 Server Windows for Workgroups 1 Connecting to a Netware 3.12 Server Windows for Requirements Workgroups • HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed. • 3COM Etherlink 3C509-B ethernet card and drivers disk ver. 5.0. DOS ODI - File Name: 3C5X9.COM Size: 42KB Date: 7/21/96 • DOS and MS-Windows for Workgroups 3.11 media. • Novell Netware server 3.12 that supports Net BEUI, NWLink IPX/SPX, and NWLink NetBIOS transfer protocols. • Netware client
Streszczenie treści zawartej na stronie nr. 4
1 Connecting to a Netware 3.12 Server Windows for Workgroups 4 Select “CONFIGURE NIC,” and verify the resource settings listed above under the heading “Device Configuration.” 5 If changes are required, save those changes and exit. 6 Remove the 3com cards driver diskette and insert Netware client for DOS and MS-Windows disk 1. 7 Execute INST_DOS.EXE and enter yes to accept the agreement if you are using a Vectra VL8, then go directly to step 8. If you are using a Vectra VL7 or VE7/VE8, compl
Streszczenie treści zawartej na stronie nr. 5
1 Connecting to a Netware 3.12 Server Windows for Workgroups 9 Select 16-bit LAN Drivers and hit the enter key. 10 Page down the Board Drivers list to “USER SPECIFIED 16 BIT DRIVER” and hit enter. 11 Insert the 3COM Etherlink 3C509 Ethernet card and drivers disk, set the path to “A:\NWCLIENT\” and press enter. 12 Select “3Com Etherlink III Parallel Tasking Family” and press enter. 13 Accept the default settings, press “F10” to continue, and verify the following entries for the “Installation C
Streszczenie treści zawartej na stronie nr. 6
1 Connecting to a Netware 3.12 Server Windows for Workgroups
Streszczenie treści zawartej na stronie nr. 7
1 Connecting to a Netware 3.12 Server Windows 95 SR2 Windows 95 SR2 Requirements • HP Vectra with Windows 95 SR2 installed. • 3COM Etherlink 3C509-B ethernet card and drivers disk ver. 5.0. • Vectra VL8 Driver Name: W95EL5X9.INF Size: 16KB Date: 6/11/97 • Vectra VL7 Driver Name: Elnk.VXD Size: 30KB Date: 7/18/96 • Vectra VE7/VE8 Driver Name: W95EL5X9.INF Size: 16KB Date: 6/11/97 • Windows 95 SR2 media. • Novell Netrware 3.12 server that supports Net BEUI, NWLink IPX/SPX, and NWLink NetBIOS t
Streszczenie treści zawartej na stronie nr. 8
1 Connecting to a Netware 3.12 Server Windows 95 SR2 5 If changes are required, save those changes and exit. 6 Remove the 3com cards driver diskette and restart the machine. 7 After windows loads, click on “Start,” to “Settings” and over to “Control Panel.” 8 Double click on “Network” and select “Add.” 9 Choose to add an adapter, click on “Add” then on “Have Disk.” 10 Insert the 3C509B drivers diskette and set path to “A:\” and hit enter. (If you have a Hewlett-Packard pre-loaded HDD, set the
Streszczenie treści zawartej na stronie nr. 9
2 Connecting to a Netware 4.11 Server Windows for Workgroups 2 Connecting to a Netware 4.11 Server Windows for Requirements Workgroups • HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed. • 3COM Etherlink 3C509-B ethernet card and drivers disk ver. 5.0. DOS ODI - File Name: 3C5X9.COM Size: 42KB Date: 7/21/96 • DOS and MS-Windows for Workgroups 3.11 media. • Novell Netware server 4.11 that supports Net BEUI, NWLink IPX/SPX, and NWLink NetBIOS transfer protocols. • Netware clien
Streszczenie treści zawartej na stronie nr. 10
2 Connecting to a Netware 4.11 Server Windows for Workgroups 6 Remove the 3COM cards driver diskette and insert Netware client for DOS and MS-Windows disk 1. If you are using a Vectra VL8, go straight to step 7. If you are using a VL7 or VE7/VE8, finish the installation by using the instructions below. a Execute INSTSTALL.EXE. b Specify the settings as listed below: • C:\NWCLIENT •Yes •Yes • C:\WINDOWS •No • 3Com Fast Etherlink/Etherlink III Bus Master for VE7/VE8, (or 3COM Etherlink III Pa
Streszczenie treści zawartej na stronie nr. 11
2 Connecting to a Netware 4.11 Server Windows for Workgroups 10 Page down the Board Drivers list to “USER SPECIFIED 16 BIT DRIVER” and hit enter. 11 Insert the 3COM Etherlink 3C509 Ethernet card and drivers disk, set the path to “A:\NWCLIENT\” and press enter. 12 Select “3Com Etherlink III Parallel Tasking Family” and press enter. 13 Accept the default settings, press “F10” to continue, and verify the following entries for the “Installation Configuration Summary”: ❒ YES ❒ C:\NOVELL\CLIENT32 ❒
Streszczenie treści zawartej na stronie nr. 12
2 Connecting to a Netware 4.11 Server Windows for Workgroups
Streszczenie treści zawartej na stronie nr. 13
2 Connecting to a Netware 4.11 Server Windows 95 SR2 Windows 95 SR2 Requirements • HP Vectra with Windows 95 SR2 installed. • 3COM Etherlink 3C509-B ethernet card and drivers disk ver. 5.0. Vectra VL8 and VE7/VE8 Driver Name : W95EL5X9.INF Size: 16KB Date: 6/11/97 • Vectra VL7 Driver Name: Elnk.VXD Size: 30KB Date: 7/18/96 • Windows 95 SR2 media. • Novell Netrware 4.11 server that supports Net BEUI, NWLink IPX/SPX, and NWLink NetBIOS transfer protocols. Device Configuration Vectra VL8 Vectra
Streszczenie treści zawartej na stronie nr. 14
2 Connecting to a Netware 4.11 Server Windows 95 SR2 6 Remove the 3com cards driver diskette and restart the machine. 7 After windows loads, click on “Start,” to “Settings” and over to “Control Panel.” 8 Double click on “Network” and select “Add.” 9 Choose to add an adapter, click on “Add” then on “Have Disk.” 10 Insert the 3C509B drivers diskette and set path to “A:\” and hit enter. (If you have a Hewlett-Packard pre-loaded HDD, set the path statement to “C:\MASTERS\LANDRV\3C509B\WIN95\”) 1
Streszczenie treści zawartej na stronie nr. 15
3 Connecting to a Windows NT Server 3.51 Windows for Workgroups Ver. 3.11 3 Connecting to a Windows NT Server 3.51 Windows for Requirements Workgroups Ver. 3.11 • HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed. • 3COM Etherlink 3C509-B ethernet card and drivers disk ver. 5.0. Driver Name: Elnk3.SYS Size: 27KB Date: 7/18/96 • Microsoft Windows NT Server 3.51 machine that suppo
Streszczenie treści zawartej na stronie nr. 16
3 Connecting to a Windows NT Server 3.51 Windows for Workgroups Ver. 3.11 7 After windows loads, open the “NETWORK” Program Group, and double- click on “Network Setup.” 8 Select the “Networks” button in the “Network Setup” dialog box. 9 Click on the “Install Microsoft Windows Network:” option, and click “OK.” 10 Click on the “Drivers” button from the “Network Setup” dialog box, and click on “Add Adapter”. 11 Click “OK” to accept the default choice of “Unlisted or Updated Network Adapter.” 12
Streszczenie treści zawartej na stronie nr. 17
3 Connecting to a Windows NT Server 3.51 Windows for Workgroups Ver. 3.11
Streszczenie treści zawartej na stronie nr. 18
3 Connecting to a Windows NT Server 3.51 Windows for Workgroups Ver. 3.11
Streszczenie treści zawartej na stronie nr. 19
3 Connecting to a Windows NT Server 3.51 Windows 95 SR2 Windows 95 SR2 Requirements • HP Vectra with Windows 95 SR2. • 3COM Etherlink 3C509-B Ethernet card and drivers disk ver 5.0. • Vectra VL8 and VE7/VE8 Driver Name: W95EL5X9.INF Size: 16KB Date: 6/11/97 • Vectra VL7 Driver Name: Elnk.Vxd Size: 30.2KB Date: 7/18/96 • Windows 95 media. • Microsoft Windows NT Server 3.51 machine that supports Net BEUI, TCP/ IP, NWLink IPX/SPX, and NWLink NetBIOS transfer protocols. Device Configuration Vect
Streszczenie treści zawartej na stronie nr. 20
3 Connecting to a Windows NT Server 3.51 Windows 95 SR2 under the heading “Device Configuration.” 6 If changes are required, save those changes and exit. 7 Remove the 3Com Software driver diskette and reboot the machine. 8 Click on “Start” and point to “Settings”, then select the “Control Panel.” 9 In the Control Panel group, double click on the “Network” icon . 10 In the “Network” dialog box , click on the “Add” button . 11 In the “Select Network Component Type” dialog box, highlight “Adapter
